Atdec AF-M Manuel utilisateur

AF-M Page 1 of 4

Cable Clip

(x1)

Pole

Top Cap

(x1)

Bolt Through

Base

(x1)

2mm

Allen key

(x1)

5mm

Allen key

(x1)

Security Screw

M4 x 16mm

(x1)

Mounting

screws

M4 x 10mm

(x4)

Mounting

screws

M4 x 12mm

(x4)

Mounting

screws

M4 x 16mm

(x4)

Desk clamp

assembly

(x1)

Screw

M8 x 60mm

(x1)

Screw

M8 x 30mm

(x1)

Steel

Washer

(x1)

Cable

Stops

(x2)

Pole

Assembly

(x1)

VESA

head

(x1)

Installation Guide

AF-M

Micro Desktop Monitor Mount

COMPONENT CHECKLIST

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is compatible with the range of AF Poles and arms.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the

capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further

information.

REQUIRED TOOLS

WEIGHT RANGE

• Phillips Head Screwdriver

Flat Monitors

0 - 8kg

(0 - 17.6lbs)

Curved Monitors

0 - 5.5kg

(0 - 12lbs)

AF-M Page 2 of 4

1. Desk overview

The desk clamp bracket

can be repositioned to

suit different mounting

surface thicknesses.

2. How to reconfigure desk clamp

2.1 Remove screws

(M8 x 16mm Countersunk screw)

2.2 Remove clamp plate 2.3 Invert bracket 2.4 Replace clamp plate 2.5 Reattach bracket

Pressure Plate

M10 Desk Clamp Screw

5mm Allen Key

M8 x 30mm

Countersunk

screw Tighten

firmly

3.2 Place in desired location 3.3 Screw pressure plates in and tighten firmly.3.1 Attach clamp to post

3. Post mount configuration

Default Inverted

MIN THICKNESS - 0mm (0”)

MAX THICKNESS - 39mm (1.5”)

MIN THICKNESS - 35mm (1.4”)

MAX THICKNESS - 76mm (3”)

52mm

(2.1”)

55mm

(2.2”)

88mm

(3.5”)

140mm

(5.5”)

Desk Clamp

4. Bolt through - Drill Hole

9mm

(3/8”)

25mm

offset

5. Bolt Pole to work surface

Note orientation of

plate with pole

5mm

Allen Key

M8x60mm

Screw

Bolt

Through

Plate

Steel

Washer

4.1 Drill 9mm hole in

desired post position

on work surface.

AF-M Page 3 of 4

100mm

6. Install VESA monitor head

VESA monitor

head

Screen

M4x10/12/16mm

Phillips Head Mounting

Screws

6.1 Install VESA monitor head as shown.

7. Mounting Monitor

8. Unlock/Lock Arm Rotation (Note: Focus Micro comes assembled in the “Locked” Position.)

Pole

2mm Allen Key

Grub ScrewMicro Arm

2mm Allen Key

Grub Screw

Grub Screw Hole

Slot in Pole

VESA monitor head

Arm Assembly

7.2 OPTIONAL SECURITY SCREW

Ensure the Monitor is supported, then loosen the Monitor head

screw with the 5mm Allen Key and tilt screen up before installing

the M4 x 16mm Security Screw into the Security Screw hole

Note: Support Screen

when adjusting tilt.

7.1 Insert VESA monitor head into the

receptacle in the Arm Assembly

Unlock

If you wish your Focus Micro Arm to have 360º rotation

about the Pole you will need to unlock the arm’s rotation

Step 1: Unlock the arm by turning the Grub Screw

anti-clockwise removing the Grub Screw completely

Note: Store the Grub Screw in a safe place if you are to

return the arm to the Locked position

Lock

If you have unlocked your Focus Micro Arm, but wish to

fix rotation around the Pole, you will need to lock the arm

Step 1: Ensure the hole for the Grub Screw in the Micro

Arm is lined up with the centre of the Slot in the Pole

Step 2: Re-insert the Grub Screw

previously removed. Turn the Grub

Screw clockwise until it is tight.

Do not over-tighten

5mm Allen Key

Phillips Head

Screwdriver

Loosen

Tighten

Security Screw

Hole

M4 x 16mm

Security Screw

Monitor head

screw

AF-M Page 4 of 4

9.1 Unlock Handgrip ensuring both

screen and arm assembly are supported

9.2 Lift/Lower Screen to the desired

height. Move both Screen and Arm

assembly together.

9.3 Lock Handgrip firmly.

9. Adjusting Height

Note: If Focus Micro

is to be used in a multi

user environment, use

the supplied Cable Clip

to secure the display’s

cables to the Pole.

Cable Stop

Cable Clip

Note: Ensure enough

cable slack is given to

allow for movement.

Note: If Focus Micro

is to be used in a multi

user environment, use

the supplied Cable Clip

to secure the display’s

cables to the Pole.

Cable Stop

Cable Clip

Note: Ensure enough

cable slack is given to

allow for movement.

10.2 After connecting cables,

Cable Clips and Cable Stops can

be installed to further manage

cables. Please See Over.

10. Cable Management

11. Insert Cable Stops

Note: Press down firmly onto

the other edge of the Cable

Stop and hold. This allows the

rear profile to flex in place

11.1 Insert Cable Stop on one

edge of the Pole Slot

11.2 Insert allen key into top cap

on pole

12. Adjusting the Display Bracket

Allen Key

Storage

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)

No Allen Key

necessary

No Allen Key necessaryNote: Support Screen when

adjusting tilt.

100mm

5mm Allen Key

Tighten

Loosen

VESA 75 x 75 / 100 x 100mm

Table des matières

Autres manuels Atdec Support et étagère

Atdec

Atdec VFS-Q Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec TH-3060-UF Manuel utilisateur

Atdec

Atdec A-STSWW-A Manuel utilisateur

Atdec

Atdec Levitate L-PB Manuel utilisateur

Atdec

Atdec AF-WD Manuel utilisateur

Atdec

Atdec Visidec VF-AT-NP Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AWM-X40 Manuel utilisateur

Atdec

Atdec AWM 710 Arm Manuel utilisateur

Atdec

Atdec Visidec Freestanding Double Manuel utilisateur

Atdec

Atdec AF Series Manuel utilisateur

Atdec

Atdec Visidec Focus Articulated Arm Wall Instructions de fonctionnement

Atdec

Atdec Focus VF-AT-NP Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-H Manuel utilisateur

Atdec

Atdec 8060 Manuel utilisateur

Atdec

Atdec AWM 460 Arm Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-FS Manuel utilisateur

Atdec

Atdec AWMS-3-137140-C Manuel utilisateur

Atdec

Atdec VFS-DH Manuel utilisateur

Atdec

Atdec AD-WM-5060 Manuel utilisateur

Atdec

Atdec AWMS-2-LTH75-H Manuel utilisateur

Atdec

Atdec AWMS-2-4640-C Manuel utilisateur

Atdec

Atdec AD-TVC-45 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur