Atdec AWMS-46W35 Manuel utilisateur

AWMS-46W35 | Page 1 of 7

Installation Guide

AWMS-46W35

Single Monitor Arm on Wall Mount

COMPONENT CHECKLIST RANGE

CONTENTS

AWM-A46

460 Arm

(x1)

AWM-W35

350 Wall Channel

(x1)

350 Wall Channel

Page 2

Page 3

460 Arm

Page 4

Page 5

AWM-W35

Component Checklist

Channel Installation

AWM-A46

Component Checklist

Arm Installation

AWMS-46W35 | Page 2 of 7

AWM-W35

Wall Channel

COMPONENT CHECKLIST

REQUIRED TOOLS

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is compatible with Atdec modular (AWM) products.

! The manufacturer accepts no responsibility for incorrect installation.

Wall channel

(x1)

Nylon

Anchor (x3)

Top Cap

Screws

(x2)

Top Cap

(x1)

M6 x 50mm

Countersunk

Screw (x3)

• Power Drill

• 4mm (5/

32”) Drill Bit

• 8mm (5/

16”) Drill Bit

• Phillips Head Screwdriver

AWMS-46W35 | Page 3 of 7

3. Install top cap 4. Cable clips

4.1 Push the cable down into the Cable Clip.

4.2 Insert one side of the

Cable Clip into the Channel

on the Post assembly

or Wall Channel, before

pushing the other side in.

3.1 Attach Top Cap

Phillips Head

Screwdriver

Top Cap

1.1 Masonry 1.2 Timber stud

1. Install Wall Channel - Ensure all fasterners are installed

Note: Cable clips

sold separately in

packs of four.

8mm (5/

16”) holes

4mm (5/

32”) holes

Stud

Nylon anchors

M6 x 50mm

Screws M6 x 50mm

Screws

2. Fit channel clamp to wall channel

2.1 Ensure knob is undone. 2.2 Slide clamp into channel.

Push knob to

aid insertion

2.3 Hold clamp in desired position on post

and turn knob to lock in place.

1. Ensure Knob is undone

Tip: push knob

to aid insertion

2. Slide clamp into channel

3. Hold clamp in desired position on post and turn

knob to lock in place

AWMS-46W35 | Page 4 of 7

AWM-A46

460 Arm

COMPONENT CHECKLIST

Monitor Arm

(x1)

VESA Head

(x1)

Screw

M4x25mm

(x4)

Screw

M4x16mm

(x4)

Screw

M4x12mm

(x4)

Spacer

(x4)

Security

screw

(x1)

4mm

allen key

(x1)

Post Clamp

(x1)

REQUIRED TOOLS

WEIGHT RANGE

Flat Monitors

0 - 12kg

(0 - 26.5lbs)

Curved Monitors

0 - 8kg

(0 - 17.6lbs)

• Phillips Head Screwdriver

Monitor weight should be within the

weight range of all modular elements

that make up the complete monitor

mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec AWM Series products.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the

capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further

information.

AWMS-46W35 | Page 5 of 7

3. Place the rotation ring

in the desired postion

2. Set arm rotation to 180° (optional)

2.1 Remove plastic sleeve

from post clamp.

2.2 Remove rotation ring. 2.3 Place rotation ring in

desired position.

Note: rotation ring placement

depends on the position of the clamp

on the post. The tag on the ring

should always face toward the user.

1. Remove plastic sleeve

2. Remove rotation ring

1. Press

2. Lift

Note rotation is set to 360� by default.

180°

360°

Default

Position

Flipped

Position

Tag

1. Fix clamp to Post or Wall Channel

1.1 Ensure knob is undone. 1.2 Slide post clamp into channel.

Push knob to

aid insertion

1.3 Hold clamp in desired position on

channel and turn knob to lock in place.

1. Ensure Knob is undone

Tip: push knob

to aid insertion

2. Slide post clamp into channel

3. Hold clamp in desired position on post and turn

knob to lock in place

3. Fit arm onto post clamp

Note: Check the

arm rotation is

smooth after

tightening.

3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.

1. Push arm onto clamp

2. Ensure arm is fully pushed onto clamp

3. Tighten set screw

Tip: Check the

arm rotation is

smooth after

tightening.

AWMS-46W35 | Page 6 of 7

Tighten

Loosen

Tighten

Loosen

5. Mount monitor

Monitor arm

5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to secure

it to the arm assembly

5.2 Ensure that the VESA head sits flush within

the monitor arm. There should be no gap

Gap No gap

6. Adjust tilt tension & Install security screw

6.1 Use the allen key to adjust the tilt tension until the monitor

holds in a vertical position at the end of the arm.

Note: Support

monitor while

adjusting.

6.2 OPTIONAL security screw

To install the optional security screw tilt the head upwards

4. Attach VESA head to monitor

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

4.2 Screw the VESA head onto monitor

Note spacers may be required for curved,

recessed or uneven monitor surfaces.

4.3 Ensure the correct screw length is used

to attach the monitor.

4.1 VESA mounting compatibility

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: For other sizes, use a suitable

adaptor plate (sold separately).

AWMS-46W35 | Page 7 of 7

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Note: The cable cover shown

does not come with all posts

7.4 To reposition the cable cover, pull it

straight up and out of the post and insert

it into any of the available channels

Cable cover

Cable

Cover

Desk

Clamp

7.1 Push the cable down into the cable clip

Note: Cable clips do not

come with all posts

7.6 Feed remaining cable into cover

7.5 Loop cable and insert into cable cover

7.2 Push cable clip into post channel

7. Post cable management

7.3 Recommended post cable cover

position for double or triple arm set-ups

Note

Ensure enough cable

slack is given to allow for

movement of the monitor

Push

6. Monitor arm cable management

6.1 Plug cables into the monitor and route

the cables down the arm using the cable

hooks and clips

Alternative cable

cover positions

Table des matières

Autres manuels Atdec Support et étagère

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec VFS-DV Manuel utilisateur

Atdec

Atdec Visidec Focus Articulated Arm Wall Instructions de fonctionnement

Atdec

Atdec AWM-LTH Manuel utilisateur

Atdec

Atdec ADBS-3x1-30T3C Manuel utilisateur

Atdec

Atdec AD-TVC-70R Manuel utilisateur

Atdec

Atdec Levitate L-PB Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AWM-A71 Manuel utilisateur

Atdec

Atdec VF-AT-NP Manuel utilisateur

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-G Manuel utilisateur

Atdec

Atdec AWM-X40 Manuel utilisateur

Atdec

Atdec AWM-P G Manuel utilisateur

Atdec

Atdec SD-AT-DW Manuel utilisateur

Atdec

Atdec AD-WFP-5040 Manuel utilisateur

Atdec

Atdec TELEHOOK TH-3060-UT Manuel utilisateur

Atdec

Atdec ADBS-3x1-30TW Manuel utilisateur

Atdec

Atdec AWM-A13 Manuel utilisateur

Atdec

Atdec TH-3060-UF Manuel utilisateur

Atdec

Atdec AWM-P G Manuel utilisateur

Atdec

Atdec TH-1040-CTS Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur