Atdec AWM-A13 Manuel utilisateur

AWM-A13 Page 1 of 4

Installation Guide

AWM-A13

130 Arm

COMPONENT CHECKLIST

REQUIRED TOOLS

WEIGHT RANGE

Monitor Arm

(x1)

VESA Head

(x1)

Screw

M4x25mm

(x4)

Screw

M4x16mm

(x4)

Screw

M4x12mm

(x4)

Spacer

(x4)

Security

Screw

(x1)

4mm

Hex Key

(x1)

• Phillips Head Screwdriver

Flat Monitors

0 - 12kg

(0 - 26.5lbs)

Curved Monitors

0 - 8kg

(0 - 17.5lbs)

Monitor weight should be within the

weight range of all modular elements

that make up the complete monitor

mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Do not remove/ throw away the plastic cap on channel clamp.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec AWM Series products.

! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and

offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be

within the stated range. Please contact Atdec if you would like further information.

AWM-A13 Page 2 of 4

2. Remove rotation ring

1. Press

2. Lift

3. Place the rotation ring

in the desired postion

2. Set arm rotation to 180° (optional)

2.3. Remove plastic sleeve from

post clamp..

2.1. Loosen tilt head joint

screw.

2.2. Remove tilt head from channel

clamp.

2.4. Remove rotation ring. 2.5. Place

rotation ring

in desired

position

and replace

plastic sleeve.

NOTE: Place the rotation ring

depending on what post channel

the arm will be attached to. The tag

should always face toward the user.

1. Remove plastic sleeve

Note rotation is set to 360° by default.

180°

360°

Default

Position

Flipped

Position

Tag

2.6. Fit tilt head back

onto channel clamp.

2.7. Ensure tilt head is

fully pushed onto shaft.

2.8. Tighten joint screw.

1. Fix Arm to Post or Wall Channel

1.1. Ensure knob is undone. 1.2. Slide post clamp into channel.

Push knob to

aid insertion

1.3. Hold clamp in desired position on

channel and turn knob to lock in place.

NOTE: Check

the rotation is

smooth after

tightening.

NOTE: Ensure

plastic sleeve is

on shaft before

tting arm.

AWM-A13 Page 3 of 4

4. Mount monitor

5. Adjust tilt tension & Install security screw

3. Attach VESA head to monitor

3.2. Attach VESA head onto monitor with provided screws.3.1. Check VESA mounting

compatibility.

100mm

75mm

100mm

75mm

NOTE: For other sizes,

use a suitable adaptor

plate (sold separately).

Flush

Too long Too short

Spacer

5mm 12mm

NOTE: Be sure to use a screw

length that suits the monitor.

NOTE: Spacers may be

required for curved, recessed

or uneven monitor surfaces.

Monitor arm

4.1. Insert VESA head into the

monitor arm.

4.3. Push the lever down to

secure it to the arm assembly.

4.2. Ensure that the VESA head sits ush within

the monitor arm. There should be no gap.

Gap No gap

Tighten

Loosen

Tighten

Loosen

5.1. Use the allen key to adjust the tilt tension until the

monitor holds in a vertical position at the end of the arm.

NOTE: Support

monitor while

adjusting

5.2. (OPTIONAL) To install the optional security

screw tilt the head upwards.

AWM-A13 Page 4 of 4

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

6. Monitor arm cable management

Ensure enough

cable slack is

given to allow

for movement

of the monitor

6.1. Plug cables into the monitor and

route the cables down the arm using

the cable hooks and clips.

7. Post cable management

Load cables

into cable

cover

7.2. To route

cables down

post, start

by removing

the post’s

cable covers

and clips.

Recommended

Position

CABLE CLIPS

7.3. Load cables into cable clip.

7.4. Insert one

side of the

cable clip into

a channel on

the post, then

push in the

other side.

7.5.

(OPTIONAL)

Cable covers

can be clipped

on over the

cable clips.

7.1. Cable clips and covers can be clipped onto

any post channel however the rear channel is

recommended for good concealment.

Optional cable

cover positions

SQUEEZE

Cables can

exit from the

side of the

cable cover

PUSH

CABLE COVERS

7.6 Load cables

into cable cover.

7.7 Clip the cable

cover onto any of the

four post channels.

HINT: Cable covers have

greater cable capacity.

Autres manuels Atdec Support et étagère

Atdec

Atdec VFS-Q Manuel utilisateur

Atdec

Atdec VFS-DH Manuel utilisateur

Atdec

Atdec ADBS-3x1-30TW Manuel utilisateur

Atdec

Atdec AWM-P G Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AWM-A13-B Manuel utilisateur

Atdec

Atdec SD-AT-DW Manuel utilisateur

Atdec

Atdec AWMS-2-D13-C Manuel utilisateur

Atdec

Atdec 8060 Manuel utilisateur

Atdec

Atdec TH-1026-VF Manuel utilisateur

Atdec

Atdec Visidec VF-AT-NP Manuel utilisateur

Atdec

Atdec AWMS-DW6 Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-G Manuel utilisateur

Atdec

Atdec TH-1040-CTS Manuel utilisateur

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AD-WM-5060 Manuel utilisateur

Atdec

Atdec Visidec Focus Micro Instructions de fonctionnement

Atdec

Atdec ADBS-4x1-39TW Feuille d'instructions

Atdec

Atdec AF-AT-NBC Manuel utilisateur

Atdec

Atdec AF-WD Manuel utilisateur

Atdec

Atdec AWMS-2-4640-C Manuel utilisateur

Atdec

Atdec AV Cart 75 Manuel utilisateur

Atdec

Atdec AWMS-2-LTH75-H Manuel utilisateur

Atdec

Atdec Spacedec Acrobat Swing Arm Double Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur