Atdec Spacedec Acrobat Swing Arm Double Manuel utilisateur

Component Checklist

Installation Instructions

SPACEDEC ACROBAT

SWING ARM DOUBLE

Swing Arm

Assembly (x2)

Cable Wrap

Applicator (x1)

Top Cap Tool (x1)

2.5mm Allen

Key (x1)

Cable Clip

(x4)

Extension

Clip (x8)

Bits Box

Mounting Fasteners

M4x10mm

Screw (x8)

M4x12mm

Screw (x8)

M4x16mm

Screw (x8)

16mm Cable

Wrap (x2) Washer (x1)

Base Casting (x1)

Spacer Tube

Assembly (x2) M8 Interscrew

(x1)

M8 Nyloc Nut (x1)

Cable Manager

Tube Clip (x1)

5mm Allen

Key (x1)

M4x16mm

Countersunk

Screw (x3)

Desk Clamp Box

M8 Desk Clamp

Screw (x1)

Pressure

Plate (x1)

Inner Tube Post

Desk Clamp

Bracket (x1)

Component Checklist

Threaded Rod

and Top Cap

(x1)

Component Checklist

Possible Configurations

Spacedec Acrobat Swing Arm Double can be

assembled in a number of different configurations

depending on the users requirements.

Two such examples are shown below and right.

Arm, Spacer, Arm, Spacer

Side by side displays

Arm, Arm, Spacer, Spacer

Back to Back displays

Spacer Tube (x2)

Internal Tube Post

Top Cap and

Threaded Rod

C.1. Desk Clamp

To assemble the Desk Clamp Assembly, first place the

M8 Nyloc Nut inside the Base Casting with the Plastic

Ring facing down, then screw the Base Casting on to the

Desk Clamp Bracket using the M4x16mm Countersunk

screws.

C.1.1. Assemble the Desk Clamp

C.1.2. Attaching the Desk Clamp

Tighten

Firmly

Base Casting

Desk Clamp

Assembly

Desk Top

Pressure Plate

M8 Desk Clamp Screw

5mm Allen Key

Adjust the Desk Clamp to suit your desk thickness by

turning the M8 Desk Clamp. Screw with the supplied

5mm Allen Key

Suits 12mm (1/2”)

to 38mm (11/2”)

thick work

surfaces

Pressure Plate

M8 Desk

Clamp Screw

C.1.3. Attaching the Swing Arm Post

Use the Top Cap Tool to tighten the Threaded

Rod into the Base Casting as shown below.

Top Cap

Tool

Threaded

Rod

Base

Casting

NOTE: Desk Clamp

Assembly is suitable

for square edged

desks only.

Tighten

Firmly

NOTE: It is

recommended

that the Desk

Clamp be

attached to

the rear or

side edge

of the work

surface

DESK CLAMP ADJUSTMENT RANGE

M4x16mm

Countersunk

Screw (x3)

Base

Casting

Desk

Clamp

Bracket

M8 Nyloc

Nut

Component Checklist

Check you have received all parts against the Component Checklist on the previous page.

Assemble the Arm

Threaded Rod

and Top Cap

Swing Arm

Assembly

(x2)

Internal Tube Post Spacer Tube

(x2)

Cable Manager

Tube Clip

B.2. Assemble

the Swing Arm

Assemble the Swing Arm in

the desired configuration

ensuring all components

are used as shown.

You will need to disassemble the Tube Assembly

before assembling the Swing Arm

B.1. Disassemble the Tube Assembly

Mounting Options

Attaching the Displays

75mm x 75mm (3” x 3”) mounting hole pattern

Display

4x10mm

Screws

75mm

(3”)

75mm (3”)

100mm x 100mm (4” x 4”) mounting hole pattern

NOTE:

Ensure that the

flat side of each

Extension Clip sits

against the back

of the display

Extension Clips

4x12mm or

4x16mm Screws

100mm

(4”)

100mm (4”)

Display

Installing Cable Management

E.1. Push the four supplied Cable Clips into the holes on the underside of the Swing Arm Double as shown.

E.2. Feed the cables into the Cable Wrap Applicator.

E.3. Insert the Cable Wrap Applicator into the Cable Wrap as shown.

E.4. Squeeze the nose of the Applicator and place inside the Cable Wrap ensuring that the opening edges of the Cable

Wrap face towards the nose of the applicator as shown in diagram.

E.1.

Push in

Clips

Nose

E.2. E.3. E.4.

C.2.1. Drill Mounting Hole

Drill a 13mm (½”) hole in your work surface at the desired location for your arm.

C.2.2. Install as shown

Insert the M8 Interscrew up through the hole in the work surface.

Using both hands, secure the M8 Interscrew with the 5mm

Allen Key supplied in the Desk Clamp Box and use the other

hand to tighten the Threaded Rod into the Interscrew with the

supplied Top Cap Tool. (see diagram C.2.3.)

5mm Allen Key

Top Cap Tool

Threaded Rod

Washer

Base Casting

M8 Interscrew

13mm (1/2”) Hole

Desk Top

Tighten

Firmly

C.2.3.

C.2. Bolt Through

Attaching the Cable Wrap to the Arm

F.1. Position the displays at their highest

possible position to ensure that there is

sufficient cabling at the end of the arm

so the cables are not stretched or pulled

out when the displays are moved.

BEFORE PROCEEDING TO THE NEXT STEP PLEASE NOTE:

Swing Arm Double will only work when a display is properly installed.

DO NOT adjust tension screws or gas strut until your display has been attached.

Cable Clips (x4)

Cable Tube

Manager Clip

Cable Wrap

Mounting Options Continued

As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the international VESA standards. Due

to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 08.11.07

Installation Complete

Ergonomic Guidelines

When mounting the Spacedec Acrobat

Swing Arm Double, ensure the correct

focal distance can be achieved for

ultimate visual comfort.

Recommended Mounting Position

Adjusting the Display

The Spacedec Acrobat Swing Arm Double comes factory set to support 6kg displays. Adjust the arm to suit the weight of

your display as shown in the following steps:

3kg

display

9kg

display

Arm

5mm

Allen key

Gas Strut

Raise Gas

Strut to suit

lighter

display

Lighter

Heavier

Lower Gas

Strut to suit

heavier

display

G.3.1. Depending on the weight of the display, it may be

necessary to adjust the arm. This can be done by using the

5mm Allen Key supplied in the Desk Clamp Box.

G.3.2. If the arm tends to automatically rise or fall when

the display is attached, it will be necessary to make small

adjustments to the gas strut. (see diagram on the right)

G.3.3. If the arm tends to rise, the gas strut position should be

raised. If the arm tends to fall, the gas strut position should be

lowered.

It is possible to control the amount of resistance in the Pivot Head to suit

your display.

To increase the resistance of the Pivot Head to suit heavier displays, use the

5mm Allen Key supplied in the Desk Clamp Box to tighten the interscrew in

a clockwise direction.

To decrease the resistance of the Pivot Head to suit lighter displays,

loosen the interscrew in an anti-clockwise direction.

NOTE: It is recommended the Pivot Head be left at the

factory setting for best performance.

Pivot Head

Interscrew

5mm Allen Key

Loosen Tighten

G.2. Adjusting the Pivot Head Resistance

G.3. Adjusting the Swing Arm/Gas Strut Resistance

Depending on the weight of the display, it may be necessary

to make adjustments to the Ball Joint Mechanism. If the

display doesn’t hold its position or is too resistant, adjust

the four tension screws located around the Ball Joint (see

diagram on the right) using the supplied 2.5mm Allen Key.

Check the display, and then adjust again if necessary.

NOTE: Be sure to adjust screws evenly.

Tighten

Loosen

Tension

Screws (x4)

Ball Joint

2.5mm

Allen Key

G.1. Adjusting the Ball Joint Resistance

Table des matières

Autres manuels Atdec Support et étagère

Atdec

Atdec AWM 710 Arm Manuel utilisateur

Atdec

Atdec SPACEDEC ACROBAT Instructions de fonctionnement

Atdec

Atdec VFS-DH Manuel utilisateur

Atdec

Atdec AF-MC Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-H Manuel utilisateur

Atdec

Atdec AWM-LTH Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AWMS-2-LTH75-H Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec Freestanding Quad Manuel utilisateur

Atdec

Atdec Levitate Instructions de fonctionnement

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AWM-X40 Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-G Manuel utilisateur

Atdec

Atdec A-STSWW-A Manuel utilisateur

Atdec

Atdec AD-TVC-70A Manuel utilisateur

Atdec

Atdec AWM-A13-B Manuel utilisateur

Atdec

Atdec AF Series Manuel utilisateur

Atdec

Atdec SYSTEMA SW6S Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec Telehook Manuel utilisateur

Atdec

Atdec TELEHOOK TH-3060-UT Manuel utilisateur

Atdec

Atdec Visidec Focus Micro Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur