Atdec AF-AT Manuel utilisateur

AF-AT Page 1 of 4

COMPONENT CHECKLIST

Monitor

arm

(x1)

Pole Assembly

(x1)

VESA

head

(x1)

Rotation

limiter

(x1)

Screw

M8 x 30mm

(x1)

Pole

top cap

(x1)

Bolt through

base

(x1)

5mm

Allen key

(x1)

Mounting

screws

M4 x 10mm

(x4)

Mounting

screws

M4 x 12mm

(x4)

Mounting

screws

M4 x 16mm

(x4)

Security Screw

M4 x 16mm

(x1)

Steel

washer

(x1)

Cable

stop

(x2)

Cable

clip

(x1)

Primary arm

cable cover

(x1)

Secondary arm

cable cover

(x1)

Desk clamp

assembly

(x1)

Screw

M8 x 60mm

(x1)

Installation Guide

AF-AT

Single Arm

Desktop Monitor Mount

REQUIRED TOOLS

WEIGHT RANGE

• Phillips Head Screwdriver

Flat Monitors

0 - 8kg

(0 - 17.6lbs)

Curved Monitors

0 - 5.5kg

(0 - 12lbs)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is compatible with the range of AF Poles and arms.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the

capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further

information.

AF-AT Page 2 of 4

1. Desk overview

The desk clamp bracket

can be repositioned to

suit different mounting

surface thicknesses.

2. How to reconfigure desk clamp

2.1 Remove screws

(M8 x 16mm Countersunk screw)

2.2 Remove clamp plate 2.3 Invert bracket 2.4 Replace clamp plate 2.5 Reattach bracket

Pressure Plate

M10 Desk Clamp Screw

5mm Allen Key

M8 x 30mm

Countersunk

screw Tighten

firmly

3.2 Place in desired location 3.3 Screw pressure plates in and tighten firmly.3.1 Attach clamp to post

3. Post mount configuration

Default Inverted

MIN THICKNESS - 0mm (0”)

MAX THICKNESS - 39mm (1.5”)

MIN THICKNESS - 35mm (1.4”)

MAX THICKNESS - 76mm (3”)

52mm

(2.1”)

55mm

(2.2”)

88mm

(3.5”)

140mm

(5.5”)

Desk Clamp

4. Bolt through - Drill Hole

9mm

(3/8”)

25mm

offset

5. Bolt Pole to work surface

Note orientation of

plate with pole

5mm

Allen Key

M8x60mm

Screw

Bolt

Through

Plate

4.1 Drill 9mm hole in

desired post position

on work surface.

AF-AT Page 3 of 4

Arm Assembly

6. Install VESA monitor head

7. Install arm assembly

Handgrip Tab

5mm

Allen Key

Pole

Top Cap

VESA monitor

head

Screen

M4x10/12/16mm

Phillips Head Mounting

Screws

6.1 Install VESA monitor head as shown.

7.1 Unlock handgrip and raise so

that handgrip tab protrudes

7.4 Slide the Arm Assembly and

Handgrip down the pole before locking

the handgrip at the desired height

7.5 Insert Pole Top

Cap into Pole. This is

also where the Allen

Key is stored.

7.3 Slip the Arm Assembly

over the Handgrip Tab and

then onto the Pole

7.2 OPTIONAL ROTATION LIMITER

Insert rotation limiter for 180�

rotation around mounting pole

100mm

75mm

100mm 75mm

8. Mounting Monitor

VESA monitor head

Arm Assembly

8.2 OPTIONAL SECURITY SCREW

Ensure the Monitor is supported, then loosen the Monitor head

screw with the 5mm Allen Key and tilt screen up before installing

the M4 x 16mm Security Screw into the Security Screw hole

Note: Support Screen

when adjusting tilt.

8.1 Insert VESA monitor head into

the receptacle in the Arm Assembly

5mm Allen Key

Phillips Head

Screwdriver

Loosen

Tighten

Security Screw

Hole

M4 x 16mm

Security Screw

Monitor head

screw

AF-AT Page 4 of 4

Cable

Stop

Cable

Clip

Note: Ensure enough cable

slack is given to allow for

movement.

Lock Slot

Elbow Joint

‘click’

Lock Slot

Elbow Joint

‘click’

9.1 Unlock Handgrip ensuring both the

screen and arm assembly are supported

10.1 After plugging in your cables,

install the Cable Covers.

Insert Cable Covers

up into Lock Slots.

10.2 Push Cable Covers away from

Elbow Joint to secure in place.

9.2 Lift/Lower the Screen to the desired

height. Move both Screen and Arm

assembly together

9.3 Lock Handgrip firmly

10.3 Cable Clips and Cable Stops can be installed

to further manage cables.

9. Adjusting Height

10. Cable Management

11. Insert Cable Stops

Note: Press down firmly onto

the other edge of the Cable

Stop and hold. This allows the

rear profile to flex in place

11.1 Insert Cable Stop on one edge

of the Pole Slot

11.2 Insert allen key into top cap

on pole

12. Adjusting the Display Bracket

Allen Key

Storage

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)

No Allen Key

necessary

No Allen Key necessaryNote: Support Screen when

adjusting tilt.

100mm

75mm

100mm 75mm

5mm Allen Key

Tighten

Loosen

VESA 75 x 75 / 100 x 100mm

Autres manuels Atdec Support et étagère

Atdec

Atdec AD-AC-PH Manuel utilisateur

Atdec

Atdec TH-3060-UF Manuel utilisateur

Atdec

Atdec Visidec Freestanding Double Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec Visidec Focus Articulated Arm Wall Instructions de fonctionnement

Atdec

Atdec AWM 710 Arm Manuel utilisateur

Atdec

Atdec AD-WM-5060 Manuel utilisateur

Atdec

Atdec TH-PFK Manuel utilisateur

Atdec

Atdec AWMS-2-4640-C Manuel utilisateur

Atdec

Atdec SD-AT-DW Manuel utilisateur

Atdec

Atdec VF-AT-NP Manuel utilisateur

Atdec

Atdec ADBS-3x1-30TW Manuel utilisateur

Atdec

Atdec AWMS-BT40 Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-H Manuel utilisateur

Atdec

Atdec Visidec Focus Micro Instructions de fonctionnement

Atdec

Atdec AWMS-2-D13-C Manuel utilisateur

Atdec

Atdec TH-1026-VF Manuel utilisateur

Atdec

Atdec AWM-FC Manuel utilisateur

Atdec

Atdec AD-TVC-70A Manuel utilisateur

Atdec

Atdec A F -AT-W Manuel utilisateur

Atdec

Atdec VFS-DV Manuel utilisateur

Atdec

Atdec AWM-LR Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec A-STSWW-A Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur