Advantech PCE-5133 Manuel d'installation et d'exploitation

PCE-5133/5033 Startup Manual 1

Packing List

Before you begin installing your card, please make sure that

the following items have been shipped:

1. PCE-5133/5033 PICMG 1.3 single host board

2. PCE-5133/5033 startup manual P/N: 2041513300

3. Serial ATA HDD data cables P/N: 1700003194

4. COM cable with bracket P/N: 1701090401

If any of these items are missing or damaged, please con-

tact your distributor or sales representative immediately.

Note 1: For detailed contents of PCE-5133/5033, please

refer to user manual on the Advantech Website.

Note 2:  AcrobatReaderisrequiredtoviewanyPDFle.

Acrobat Reader can be downloaded at: get.

adobe.com/reader (Acrobat is a trademark of

Adobe)

PCE-5133/5033 - LGA1700 Intel®CoreTM i9/i7/i5/i3/

Pentium®ECC/non-ECC PICMG 1.3 Single Host

Board with DDR5/M.2 (2280)/Dual 2.5GbE LAN

Startup Manual

General

• LGA1700 12th Intel®Core™ i9/i7/i5/i3/Pentium®

• BIOS: AMI 256 Mb SPI BIOS

• Chipset:

- PCE-5133: Intel R680E

- PCE-5033: Intel H610E

• System memory:

- PCE-5133: Supports dual channel DDR5 4800

32GB per DIMM with ECC/non-ECC; Max. capacity is

up to 64GB

- PCE-5033: Supports dual channel DDR5 4800 32GB

per DIMM without ECC; Max. capacity is up to 64GB

Note: Please select Intel ECC supported processor to

enable ECC function.

Warning:Powermustbeturnedo󰀨beforeplugging/un-

plugging memory stick to avoid system crash or

damage of memory stick.

• SATA Ports:

- PCE-5133: 6 x SATA3.0 ports with SW Raid 0,1,5,10.

- PCE-5033: 4 x SATA3.0 ports without Raid function.

• M.2 Ports:

- PCE-5133: M.2 2280 type M module and compatible to

PCI Express 4.0

• Serial ports: 2 x RS-232 with pin headers

• Watchdog timer: 255 level timer intervals

• USB 2.0:

- PCE-5133/5033: 6*USB2.0 (USB Type A*1+Rear*1, 4

on backplane)

• USB 3.2:

- PCE-5133: 6*USB3.2 (Gen1) (Pin-header*6), 2*USB3.2

(Gen2) (type A, Rear I/O)

- PCE-5033: 2*USB3.2 (Gen1) (Pin-header*2), 2*USB3.2

(Gen1) (type A, Rear I/O)

• GPIO: One programmable 8-bit GPIO pin-header

• DP1 & DP2: DVI/Displayport/HDMI via optional cable

VGA Interface

• Chipset: Intel®UHD Graphics

• Shared system memory is subject to OS

Ethernet Interface

• Chipset supports:

- LAN 1: I225LM(PCE-5133); I226V(PCE-5033)

- LAN 2: I225LM(PCE-5133); I226V(PCE-5033)

• Connection: 2 x on-board RJ-45 connectors with LED

indicators.

Note:Powermustbeturnedo󰀨beforeinstalling/unin-

stalling any expansion modules.

Specications

For more information on this and other Advantech prod-

ucts, please visit our website at:

http://www.advantech.com

For technical support and service, please visit our sup-

port website at:

https://advt.ch/PCE-5133G2

https://advt.ch/PCE-5033G2

extra warranty for Free at:

http://www.register.advantech.com

This manual is for the PCE-5133/5033

Part No. 2041513300

Printed in China

1st Edition

January 2023

2 PCE-5133/5033 Startup Manual

Mechanical and Enviromental

• Dimensions: (L x W): 338 x 122 mm

• Power supply voltage: +12 V, +5 V, +3.3 V, +5 V

• Power requirements(Idle):

Voltage + 3.3V +5V +12V

Current 8.34A 4.13A 6.86A

Note: Testing conditions:

CPU: Processor: Intel®i9-12900E

Memory: 2 DDR5 4800 32GB

Operating temperature: 0 ~ 60° C (depending on

CPU)

• Weight: 0.5 kg (weight of board)

The board has a number of jumpers that allow you to con-

gureyoursystemtosuityourapplication.Thetablebelow

lists the function of each of the jumpers and connectors.

Connectors

Label Function

COM1 RS-232 (9-pin Box Header)

COM2 RS-232 (9-pin Box Header)

CPU FAN1 4-pin fan power connector for supporting

PWM or DC CPU fan

DP1 & DP2 Display port/DVI/ HDMI via optional

cables

eSPI eSPI expansion pin header for COM

module

HDAUD1 Advantech HD audio module expansion

pin-header

JFP1 Power switch/reset connector

JFP2 External speaker/HDD LED connector/

SMBus connector

JFP3

Power LED

Suspend:fastash(ATX/AT)

Systemon:on(ATX/AT)

Systemo󰀨:o󰀨(ATX/AT)

JPCICLK

PCI clock selection

LAN1 Intel i225LM (PCE-5133)

Intel i226V (PCE-5033)

LAN2 Intel i225LM (PCE-5133)

Intel i226V (PCE-5033)

LANLED1 LAN LED

NVMe M.2 M.2 key 2280 with PCIe Gen. 4

SATA0 &1 Port 0 & 1 (PCE-5133)

SATA4~7 SATA port 4, 5, 6, 7 (PCE-5133/5033)

SPI_TPM1 SPI expansion pin header for TPM

module

Sysfan1 4 PIN fan power connector for support-

ing PWM or DC fan

USB2A1 USB2 port 2

USB2C1 USB2 port1

USB3C1 USB3 port1

USB3C2 USB3 port2

USB3H1 USB3 port 3,4

USB3H2 USB3 port 7, 8 (PCE-5133)

USB3H3 USB3 port 5, 6 (PCE-5133)

VGA1 VGA connector

Jumpers

Label Function

JCMOS1 CMOS clear

JME1 Clear ME data

JPCICLK1

PCI clock selection

JWDT1+

JOBS1 Watchdog timer output and OBS alarm

JPCICLK: PCI clock selection

Closed Pins

Result

1-2

66 MHZ

2-3

*33 MHZ

*Default

66 MHZ 33 MHZ

JESPI1+JESPI2: eSPI-interface COM module setting

Closed Pins Result

JFV1 VGA dummy load setting

JUSB1/

JUSB2 USB power source switch

VGA dummy load setting USB power source switch

JCMOS1/JME1: Clear CMOS/ME data

Closed Pins Result

1-2 Keep CMOS/Enable ME data (Default)

2-3 Clear CMOS/Disable ME data

1 2 3

Specications(Cont.)

Jumpers and Connectors (Cont.)

Jumpers and Connectors

PCE-5133/5033 Startup Manual 3

Jumpers and Connectors (Cont.)

JWDT1+JOBS1: Watchdog timer output and OBS alarm

Closed Pins

Result

2-4, 8-10 Watchdog timer disable (2-4)

OBS beep (8-10)

4-6, 8-10 *Watchdog timer reset (4-6)

OBS beep (8-10)

* Default

Watchdog timer disable (2-4) *Watchdog timer reset (4-6)

OBS beep (8-10) OBS beep (8-10)

JESPI1+JESPI2: eSPI-interface COM module setting

Closed Pins

Result

1-2 Watchdog timer disable (2-4)

OBS beep (8-10)

2-3 *Watchdog timer reset (4-6)

OBS beep (8-10)

* Default

*COM module disabled COM module enabled

Note!

1. Do not change default settings if an eSPI-interface

COM module is not installed; otherwise system will not

turn on.

2. If start to use the COM module, please follow the proce-

dures to prevent system from not to boot up: install the

moduleafterpower-o󰀨,setJESPI1+JESPI2to2-3pins

closed,poweronsystemtoBIOSPOSTscreen,turno󰀨

AC power, then power on.

JFV1: VGA dummy load setting

Closed Pins

Result

1-2 Enable VGA dummy load

2-3 *Disable VGA dummy load

* Default

Enable VGA dummy load *Disable VGA dummy load

Note! It is recommended to leave this function disabled

if you use DVI/DP as your main display.

1 2 3

JUSB_1 & JUSB_2 (onboard USB): USB Power

source switch between +5V and +5V_Dual

Closed Pins

Result

1-2 *USB +5V_DUAL power

2-3 USB +5V power

* Default

*USB +5 V_DUAL power USB +5 V power

The drivers for the PCE-5133/5033 are located on the

Advatecho󰀩cialwebsites.Pleasevisittheo󰀩cialwebsite

for downloading.

https://support.advantech.com/support/new_default.aspx

Caution! The computer is supplied with a battery-powered

real-time clock circuit. There is a danger of explo-

sion if battery is incorrectly replaced. Replace

only with same or equivalent type recommended

by the manufacturer. Discard used batteries ac-

cording to manufacturer’s instructions.

This device complies with the requirements in Part 15 of

the FCC rules. Operation is subject to the following two

conditons:

1. This device may not cause harmful interference;

2. This device must accept any interference received,

including interference that may cause undesired opera-

tion.

1 2 3

Jumpers and Connectors (Cont.)

Software Installation

Declaration of Conformity

4 PCE-5133/5033 Startup Manual

Figure 1: Board Layout: Jumper and Connector Locations

Note: *PCE-5033 supports 4 SATA ports (SATA4~7) and one internal USB3.2 pin-header.

*PCE-5033 does not feature NGFF(M.2).

Figure 2: Board Layout - Jumpers and Connector Locations

Preliminary

System FAN1 DIMMA1

CPU1 DP1 PCH GPIO1 HDAUD1

DP2 COM2 COM1 SPI_TPM1

eSPI

M.2 NVMe

USB3H2 SATA0-1

LANLED1

CPU FAN1 DIMMB1

SATA4-7USB3H3

USB2A1

USB2C1

USB3H1

USB3C2

USB3C1

VGA1

LAN12

JFP1 & JFP2

JFP3

JUSB2

JUSB1

JWDT1 & JOBS1

JCMOS1 JME1

JCASE1

GPIO1

JFV1

JESPI1 & 2

ESPI1

Board Layout

Ce manuel convient aux modèles suivants

Autres manuels Advantech Matériel informatique

Advantech

Advantech AMAX-4870 Manuel d'installation et d'exploitation

Advantech

Advantech MIO-5270 Manuel d'installation et d'exploitation

Advantech

Advantech FWA-3700 Manuel utilisateur

Advantech

Advantech PCA-6186VE Manuel utilisateur

Advantech

Advantech ARK-1551 Manuel utilisateur

Advantech

Advantech MIC-75M11 Manuel d'installation et d'exploitation

Advantech

Advantech MIC-710AIL Manuel utilisateur

Advantech

Advantech AIMB-592 Manuel utilisateur

Advantech

Advantech PCA-6119P7 Manuel d'installation et d'exploitation

Advantech

Advantech SKY-MXM-A1000 Manuel utilisateur

Advantech

Advantech PCA-6010 Manuel utilisateur

Advantech

Advantech PCIE-1841 Manuel utilisateur

Advantech

Advantech ROM-8720 Manuel utilisateur

Advantech

Advantech PPC RFID 98R3P300010 Manuel d'installation et d'exploitation

Advantech

Advantech PCA-6186 Manuel utilisateur

Advantech

Advantech USM-500R Manuel utilisateur

Advantech

Advantech VEGA-3311 Manuel d'instructions

Advantech

Advantech COASTIPC PPC-412 Manuel utilisateur

Advantech

Advantech ARK-10 Manuel utilisateur

Advantech

Advantech AIMC-3421 Manuel d'installation et d'exploitation

Advantech

Advantech IPC-619 Manuel utilisateur

Advantech

Advantech PCM-23U1DG-CE Manuel d'installation et d'exploitation

Advantech

Advantech POC-W243 Series Manuel utilisateur

Advantech

Advantech PCM-3350 Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur