Advantech AIMB-707 Manuel d'installation et d'exploitation
AIMB-707 Startup Manual 1
AIMB-707 LGA1200 Intel® Core™ i9/i7/i5/i3 ATX with
Dual Display, M.2, USB 3.2, and DDR4
Startup Manual
Specications (Cont.)
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our sup-
port website for AIMB-707 at:
http://advt.ch/aimb707spt
Register your products on our website and get 2 months
extra warranty for free at:
http://www.register.advantech.com
This manual is for the AIMB-707 series Rev. A1.
Part No. 2041070701
Printed in China
2nd Edition
February 2023
• M.2 socket: One M.2 socket supports up to PCIe x2 M-
Key 2280 type storage devices.
• SATA interface: Four onboard Serial ATA 3.0 connectors
support data transmission rates of up to 600 MB/s. All
four SATA 3.0 ports support Advanced Host Controller
Interface (AHCI) technology.
• PCIe and PCI slots: One PCIe x16 expansion slot, 2x
PCIe x4 expansion slots (x1 link), 4x PCI slots 32-bit / 33
MHz PCI 2.2 compliant
• USB 3.2/2.0: Six USB 3.2 Gen 1 ports (6 rear), 4x USB
2.0 ports (2x via header, 2x internal Type-A)
• LPC interface: Advantech-designed LPC connector
supports dTPM 2.0 module and COM port extension
modules.
• Serial ports: Up to 6x serial ports: COMD1, COMD2 and
COM 4 ~ 6 are RS-232; COM3 is RS-232/422/485 with
jumper and BIOS menu options.
• Keyboard/mouse connector: The motherboard is not
equipped with a rear PS/2 connector for keyboard/mouse.
A 6-pin onboard header is supported for an optional PS/2
keyboard/mouse cable.
• Watchdog timer: 255 sec timer intervals
Graphics Interface
• Chipset: CPU integrated graphics controller.
• Display memory: One GB maximum shared memory
with 2x GB and above system memory installed
• DVI-D: Resolution up to 1920 x 1200 @ 60 Hz refresh
rate
• VGA: Resolution up to 1920 x 1200 @ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:
Intel®
I219-V;
LAN2 (G2 SKU only):
Intel®
I210-AT
Mechanical and Environmental
• Dimensions (L x W): 304.8 x 244 mm (12 x 9.6 in)
• Power supply voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
• Power consumption:
Intel® Core™ i9-10900E; DDR4 32 GB x 2.
Maximum: +3.3 V at 0.72 A, +5 V at 1.29 A, +12 V at 6.5
A, +5 Vsb at 0.11 A, -12 V at 0.04 A
• Operating temperature: 0 ~ 60 °C/32 ~ 140 °F (depend-
ing on the CPU)
• Weight of board: 0.7 kg (1.54 lb)
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x AIMB-707 motherboard
• 1 x AIMB-707 Startup Manual
• 2 x Serial ATA HDD data cables
• 1 x I/O port bracket
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Standard Functions
• CPU: LGA1200 socket supporting 10th Gen Intel®
Core™ i9/i7/i5/i3 and Pentium™/Celeron™ processors
• BIOS: AMI 128 Mbit SPI BIOS
• Chipset: Intel® H420E PCH
Note: Legacy platforms are not supported.
• System memory: Up to 64 GB in two 288-pin DIMM
sockets, supporting dual-channel DDR4 2400/2666/2933
SDRAM.AIMB-707supportsnon-ECCunbueredDIMMs
anddoesnotsupportanymemorycongurationthat
mixesnon-ECCwithECCunbueredDIMMs.
Specications
2 AIMB-707 Startup Manual
The board has a number of jumpers that allow you to con-
gureyoursystemtosuityourapplication.Thetablebelow
lists the function of each jumper and connector.
Connector / Jumper List
Label Function
LAN1 LAN1
LAN2 LAN2 (G2 SKU only)
USB3C1, USB3C3 4x USB 3.2 Gen 1 port
USB3C2 2x USB 3.2 Gen 1 port (G2 SKU
only)
USB2A1 USB 2.0 internal Type-A port
USB2A2 USB 2.0 internal Type-A port (G2
sku only)
USB2H1 2x USB 2.0 port (10-pin header)
VGA1+DVI1 VGA connector / DVI-D connector
(DVI1 for G2 SKU only)
COMD1+COMD2 Serial port: RS-232 (DB-9 con-
nector)
COM4 ~ COM6 Serial port: RS-232 (9-pin header,
G2 SKU only)
COM3 Serial port: RS-232/422/485 (9-pin
header, G2 SKU only)
KBMS1 External keyboard/mouse connec-
tor (6-pin header)
CPUFAN1 CPU fan connector (4-pin)
SYSFAN1 ~
SYSFAN3 System fan connector (4-pin)
JFP3
Keyboard lock and power LED
Suspend:fastash(ATX/AT)
Systemon:ON(ATX/AT)
Systemo:OFF(ATX/AT)
JFP2 External speaker / HDD LED con-
nector / SMBus connector
JFP1 Power switch / reset connector
AUDIO1+AUDIO2 Audio connector (Line-Out, Mic-In)
VOLT1 Alarm board power connector
JCASE1 Case open connector
LANLED1 Front panel LAN indicator con-
nector
NVME1 M.2 2280 M-Key socket (G2 SKU
only)
SATA0 ~ SATA3 Serial ATA 3.0 port
PCI1 ~ PCI4 PCI slot
PCIE1 PCIe x16 slot
PCIE2 ~ PCIE3 PCIe x4 slot (x1 link)
DIMMA1 Channel A DIMM1
DIMMB1 Channel B DIMM1
ATX12V1 ATX12Vauxiliarypowerconnec-
tor (for CPU)
EATXPWR1 ATX24-pinmainpowerconnector
(for system)
SPDIF_OUT1 SPDIF audio out pin header
GPIO1 8-bit GPIO from super I/O
SMBUS1 SMBus connector from PCH
FPAUD1 Front panel audio connector
LPC1
Low pin count connector for
Advantech dTPM 2.0 and RS232
modules
JCMOS1: Clear CMOS
JME1: Intel® ME Update
Closed Pins Result
1-2 *Keep CMOS data
*ME normal mode
2-3
Clear CMOS data
ME recovery mode
* Default
*Keep CMOS data Clear CMOS data
*ME normal mode ME recovery mode
JWDT1+JOBS1: Watchdog Timer Output and OBS Alarm
Closed Pins Result
2-4, 8-10 Watchdogtimerdisable(2-4)
OBS beep (8-10)
4-6, 8-10 *Watchdogtimerreset(4-6)
OBS beep (8-10)
* Default
Watchdogtimerdisable(2-4)*Watchdogtimerreset(4-6)
OBS beep (8-10) OBS beep (8-10)
1 2 3
1 2 3
Jumpers and Connectors Jumpers and Connectors (Cont.)
AIMB-707 Startup Manual 3
PSON1: ATX/AT Mode Selection
Closed Pins Result
1-2 AT mode
2-3 *ATXmode
* Default
ATmode*ATXmode
JUSB_1 (Rear USB), JUSB_2 (Onboard USB): USB
Power Source Switch Between +5V and +5V_DUAL
Closed Pins Result
1-2 *USB +5V_DUAL power
2-3 USB +5V power
* Default
*USB +5 V_DUAL power USB +5 V power
SMB1 (Clock), SMB2 (Data): PCIe SMBus Connection
Setting
Closed Pins Result
1-2 *Enable PCIe SMBus connection
2-3
Disable PCIe SMBus connection
* Default
*Enable PCIe SMBus connection Disable PCIe SMBus connection
Note: Both SMB1 and SMB2 jumpers should be
switched to the same setting, either 1-2 closed
or 2-3 closed.
JT1(TX Signal), JR1(RX Signal): COM3 RS-422/485
Termination Resistor
Closed Pins Result
1-2 Disable termination
2-3 *Enable termination
* Default
Disable termination *Enable termination
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
JSETCOM3: COM3 RS-232/422/485 Jumper Settings
Closed Pins Result
5-6, 7-9, 8-10,
13-15, 14-16 *RS-232
3-4, 9-11,
10-12, 15-17,
16-18
RS-422
1-2, 9-11,
10-12, 15-17,
16-18
RS-485
* Default
Note: BIOS setting changes are necessary if RS-422
or RS-485 is selected. Please refer to Chapter 3
of the user manual for additional settings.
JFV1: VGA Dummy Load Setting
Closed Pins Result
1-2 Enable VGA dummy load
2-3 *Disable VGA dummy load
* Default
Enable VGA dummy load *Disable VGA dummy load
Note: Wereccomendleavingthisfunctiondisabledif
you use DVI/DP as your main display.
1 2 3
1 2 3
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)
4 AIMB-707 Startup Manual
Declaration of Conformity
Board Layout
This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Caution! The computer is supplied with a battery-powered realtime clock circuit. There is a danger of explosion if the
battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
SATA1 SATA3
SATA0 SATA2
DIMMB1
DIMMA1
PCI3
PCIE3
PCIE1
Intel H420E PCH
Intel LGA1200 Core i9/i7/i5/i3
USB2A1
COM3
USB2H1
AUDIO1+AUDIO2
LAN2
USB3C2
LAN1
USB3C1
VGA1
DVI1
COMD1
COMD2
SYSFAN1
SYSFAN3
VOLT1 EATXPWR1 PSON1 GPIO1 SMBUS1
JCASE1
COM4
COM5
COM6
LPC1
JT1, JR1
JWDT1+JOBS1 JFP3
JFP1+JFP2
CPUFAN1
PCI1
PCIE2
PCI2
PCI4
SPDIF_OUT1 FPAUD1
KBMS1
SYSFAN2
ATX12V1
JUSB_1
JFV1
USB3C3
LANLED1
SMB1, SMB2
JUSB_2
JCMOS1
JME1
USB2A2
JSETCOM3
NVME1
3 6 9 12
25811
PWRSW RESET
HDDLED
SNMP
JFP1
&
2 5 8 11
1 4 7 10
HDDLED
SM_BUS
SPEAKER
JFP2
&
PWRLED & KEYLOCK
12345
JFP3
Figure 1: Board Layout: Jumper and Connector Locations
Autres manuels pour AIMB-707
2
Autres manuels Advantech Matériel informatique
Advantech
Advantech PCA-6143P Manuel utilisateur
Advantech
Advantech ASMB-610V3 Manuel d'installation et d'exploitation
Advantech
Advantech MIC-715 Manuel utilisateur
Advantech
Advantech PCE-5130 Manuel utilisateur
Advantech
Advantech PCM-3641P Manuel d'installation et d'exploitation
Advantech
Advantech PCA-6742 Series Manuel utilisateur
Advantech
Advantech PCI-1710 Manuel utilisateur
Advantech
Advantech PPC-IPS Manuel utilisateur
Advantech
Advantech UNO-238 V2 Manuel d'installation et d'exploitation
Advantech
Advantech ASMB-H90 Manuel d'installation et d'exploitation
Advantech
Advantech MIO-5375 Manuel utilisateur
Advantech
Advantech PCE-5B09-06 Manuel d'installation et d'exploitation
Advantech
Advantech ECU-P1522LPE Manuel d'installation et d'exploitation
Advantech
Advantech PPC-6150A Manuel utilisateur
Advantech
Advantech LGA 1700 Manuel utilisateur
Advantech
Advantech MIO-2363 Manuel utilisateur
Advantech
Advantech ARK-10 Manuel utilisateur
Advantech
Advantech MIC-300 Manuel d'installation et d'exploitation
Advantech
Advantech PCIE-1756 Manuel utilisateur
Advantech
Advantech AdvLinuxTU Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
