ZKTeco PA22 Manuel utilisateur

PA22

Version: 1.0

Quick Start Guide

Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between

the actual product and the written information in this manual.

Side

Bottom

Back Plate

Reset Button

Speaker

USBSlot

Front

Back

2.4InchTFTLCD

Keypad&

RFCardArea

LEDIndicator

Near-infraredPalm

RecognitionSensor

Tamper switch

Terminal Block

Wiring Hole

Mounting Hole

Device Overview

6.29"

(159.8mm)

4.97"

(126.1mm)

3.18"

(80.7mm)

0.76"

(19.4mm)

1.61"

(41.0mm)

47.24"

(1.2m)

Baseline

124

Install on the Wall

(56.1mm)

2.21"

Device Dimensions

Device Installation

Attach the mounting template sticker to the wall, and drill the holes according

to the mounting paper.

Fix the back plate on the wall with using wall mounting screws.

Attach the device to the back plate from top to bottom.

Fasten the device to the back plate with a security screw.

485B

485A

GND

TXD

RXD

GND

WD1

WD0

RS485B

RJ45-1

RJ45-2

RJ45-3

RJ45-6

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

BEEP

GLED

RLED

IWD1

IWD0

GND

12VOUT

BEEP

Green LED

Red LED

GND

+12V

Ethernet

RS232

Lock

Power Out

Sensor

Button

Power In

Auxiliary

Bell

Alarm

Wiegand

Out

Wiegand

8 Pin Cable Connectors

7 Pin Cable Connectors

4 Pin Cable Connectors

12 Pin Cable Connectors

2 Pin Cable Connectors

Terminal Block

Standalone Installation

Alarm

Bell

Lock

TCP/ IP

Exit Button

Door Sensor

ALARM

Wireless Router

GND

+12V DC

12V DC Adaptor

Power Connection

Without UPS

GND

+12V DC

With UPS (Optional)

12V±10%, at least 3000MA.

Use an AC adapter with a higher current ratings to share the power with other

devices.

Recommended Power Supply:

Ethernet Connection

LAN Connection

Network Cable Adaptor

RJ45-1

RJ45-2

RJ45-3

RJ45-6

Default IP address: 192.168.1.201

Subnet mask: 255.255.255.0

IP address: 192.168.1.130

Subnet mask: 255.255.255.0

Door Sensor, Exit Button, Alarm & Bell Connection

Door Sensor

Bell

Alarm

Exit Button

12V DC Adaptor

+12V DCGND

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

Connect the device and the software over an Ethernet cable. An example is

shown below:

Click [Comm.] > [Ethernet] > [IP Address], input the IP address and click

[M/OK].

Note: In LAN, the IP addresses of the server (PC) and the device must be in the

same network segment when connecting to ZKBio Access IVS software.

Lock Relay Connection

12V DC Adaptor

Magnetic Lock

+12V DC GND

FR107

Device Not Sharing Power with the Lock

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

DO NOT REVERSE

THE CONNECTION.

V- V+

NC NO

COM

Magnetic Lock

FR107

Device Sharing Power with the Lock

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

V- V+

NC NO

COM

AC Adapter

DC 12V, 3A

GND

+12V

DO NOT REVERSE

THE CONNECTION.

The system supports both Normally Opened Lock and Normally Closed Lock. The

NO Lock (Normally Opened when powered) is connected with “NO” and “COM”

terminals, and the NC Lock (Normally Closed when powered) is connected with

“NC” and “COM” terminals. The power can be shared with the lock or can be used

separately for the lock, as shown in the example with NC Lock below:

RS485 Connection

RS485 Fingerprint Reader Connection

RS485 Fingerprint Reader

DIP Settings

485-

485+

GND

+12V

GND

Distance:

more than 200 meters

485B

485A

GND

TXD

RXD

GND

WD1

WD0

12V DC Adaptor

There are six DIP switches which are located on the back of RS485 ngerprint

reader: switches 1 to 4 are for RS485 address, switch 5 is reserved, switch 6 is for

noise reduction on long RS485 cable.

If the RS485 ngerprint reader is powered from the terminal, the length of

wire should be less than 100 meters or 330 feet.

The number 6 switch should be turned on if the cable length exceeds 200

metres or 600 feet as shown below.

Wiegand Output Connection

Controller

READER 1

BEEP

GLED

WD1

WD0

GND

+12V

485B

485A

GND

TXD

RXD

GND

WD1

WD0

Wiegand Input Connection

BEEP

GLED

RLED

IWD1

IWD0

GND

12VOUT

Wiegand Reader

BEEP

GLED

RLED

DATA1

DATA0

GND

+12V

AC Adapter

DC 12V, 3A

GND

+12V

Autres manuels pour PA22

Table des matières

Autres manuels ZKTeco Terminal tactile

ZKTeco

ZKTeco ma 300 Manuel utilisateur

ZKTeco

ZKTeco LockerPad-7B Manuel utilisateur

ZKTeco

ZKTeco F305 Manuel utilisateur

ZKTeco

ZKTeco ZKBio710 Series Manuel utilisateur

ZKTeco

ZKTeco RevFace15 Manuel utilisateur

ZKTeco

ZKTeco G2 Manuel utilisateur

ZKTeco

ZKTeco ZKAIO1000W Manuel utilisateur

ZKTeco

ZKTeco G5 Manuel utilisateur

ZKTeco

ZKTeco MB10-VL Manuel utilisateur

ZKTeco

ZKTeco LPRS2000 Manuel utilisateur

ZKTeco

ZKTeco FA2000 Manuel utilisateur

ZKTeco

ZKTeco U1000F Manuel utilisateur

ZKTeco

ZKTeco FaceDepot 7B Manuel utilisateur

ZKTeco

ZKTeco F Series Manuel utilisateur

ZKTeco

ZKTeco ZK3530 Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H13 Manuel utilisateur

ZKTeco

ZKTeco VT07-C22L Manuel utilisateur

ZKTeco

ZKTeco FaceKiosk-H10A Manuel utilisateur

ZKTeco

ZKTeco D3 Series Manuel utilisateur

ZKTeco

ZKTeco MB10-VL Manuel utilisateur

ZKTeco

ZKTeco D1s Manuel utilisateur

ZKTeco

ZKTeco EFace10 Manuel utilisateur

ZKTeco

ZKTeco uFace Plus Series Manuel utilisateur

ZKTeco

ZKTeco LFace10 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur