NCR RealPOS 7460-2 Manuel

NCR RealPOS 7460-2xxx

Release 2.0

Site Preparation

200

B005-0000-1480

Issue A

The products described in this book are licensed products of NCR Corporation.

NCR is a registered trademark of NCR Corporation.

NCR RealPOS is a trademark of NCR Corporation in the United States and/or other countries.

Pentium is a registered trademark of Intel Corporation.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,

and firmware become available. NCR, therefore, reserves the right to change specifications without prior

notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the

world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,

consult with your NCR representative or NCR office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization,

and value of this book.

Written by Joseph N. Cole III

Address correspondence to:

Manager, Information Products

NCR Corporation

2651 Satellite Blvd.

Duluth, GA 30096

By NCR Corporation

Dayton, Ohio U.S.A.

Preface

This is a contractual document. It contains important warnings and

confers important legal rights and obligations. You are advised to read

it carefully.

It is the responsibility of the customer to assure that all installation

preparations are complete and in compliance with NCR specifications

and requirements and all applicable national, state, or local codes,

regulations, and laws.

Safety Requirements

The operator must connect this web kiosk to an AC outlet that is near

the terminal and is easily accessible.

Warning: This unit contains hazardous voltages and should only be

serviced by qualified service personnel.

The AC line voltage primaries are live at all times when the power cord

is connected. Therefore, disconnect the AC power cord before opening

the unit to install features or service this web kiosk.

Peripheral Usage

This web kiosk should be used only with peripheral devices that are

recommended by NCR Corporation and are certified by the

appropriate safety agency for the country of installation (UL, CSA,

TUV and VDE).

About this Book

This book provides site preparation information for terminal

components. Peripheral component and AC wiring site preparation

information is NOT provided in this book. The associated reference

documents are listed in the “Related Site Preparation Data” section.

This book contains the information necessary for the preparation of a

site that conforms to NCR specifications. It is very important that the

site complies with the requirements specified in the document because,

once the equipment has been installed, deficiencies in site preparation

or the problems caused by these deficiencies are much more difficult to

detect and correct. Further, failure to comply with these requirements

or to take proper steps to protect equipment against risks identified in

this document may cause serious damage to the equipment and to the

customer’s business.

In addition to the need to comply with the requirements specified,

electrical wiring and mechanical systems must also comply with all

relevant codes, laws, and regulations.

It is important that a customer or his agent who is fully conversant

with the special requirements of electronic equipment prepare the site.

The responsibility of ensuring that the site is prepared in compliance

with this document remains with the customer.

For information and guidance purposes only, a list is provided, in

general terms, of those matters for which the customer is responsible.

This list is not intended to be comprehensive, and in no way modifies,

alters, or limits the responsibility of the customer for all aspects of

adequate site preparation.

NCR staff will be available to answer questions relating to the contents

of this document except where:

•A customer has been notified that a full or partial consultant service

is available and/or that NCR will be willing to undertake a

preliminary or final site survey and

•The customer shall have entered into a formal contract with NCR

for provision of the same.

iii

No comment, suggestion, or advice offered or not offered about

preparation of the site, nor any inspection of the site, whether before of

after preparation, is to be taken as approval of the location of the site

and equipment or its preparation. NCR will not be liable in respect to

any comment, suggestion, or advice given by its staff or in respect to

any failure to give advice.

Finally, only the customer can know the full extent of damage that may

be caused to his business by reason of failure of the equipment which is

to be installed. For this reason, it is the customer’s responsibility to

ascertain the extent of any possible damage to his existing or planned

business, and to effect full insurance in for all eventualities.

References

•NCR RealPOS 7460-2xxx Site Preparation Guide

(B005-0000-1480)

•NCR RealPOS 7460-2xxx Hardware Service Guide

(B005-0000-1482)

•NCR RealPOS 7460-2xxx Parts Identification Manual

(B005-0000-1483)

Table of Contents

Introduction 1

Customer Responsibilities .................................................2

Where to Obtain Information Products ...........................3

AC Store Wiring Requirements ........................................3

LAN Communications .......................................................3

System Configuration Diagrams 4

Dimensions 5

7460 Terminal ......................................................................5

2183 Cash Drawer ...............................................................6

2189 Cash Drawer ...............................................................6

7197 Thermal Receipt Printer ............................................7

7167 Thermal Receipt/Impact Printer .............................7

7196 Thermal Receipt Printer ............................................8

5973 International VFD Customer Display ...................10

2336-K007 External CD-ROM Drive...............................11

Component Weights 12

Ventilation Clearance 13

Power Requirements 14

Maximum Input Power Specifications ....................14

Power Analysis for Terminal and Peripherals .......15

Cable Routing Considerations 16

Cables 17

Printers ...............................................................................19

7167, 7197 Printer (RS-232)........................................19

7167, 7197 Printer (USB) ............................................19

7196 Printer (RS-232) ........................................................20

Cash Drawers ....................................................................21

Cash Drawer, Extension Cable .................................21

PS/2 Y-Cable .....................................................................21

5964 to 7460 (RS-232/PS2/Power) .................................22

Remote Customer Displays .............................................22

5972 VFD (Parallel).....................................................22

5972 VFD (RS-232)......................................................23

5973/5974 VFD (Parallel) ..........................................23

Operator Display Cable (DVI to DVI)............................24

5945/5992 Cable (RS-232) ................................................24

Communications Cable....................................................25

Ethernet, 10/100BaseT...............................................25

Power Cables .....................................................................25

AC Power.....................................................................25

Environmental Requirements 26

Barometric Pressure..........................................................26

Temperature ......................................................................26

Humidity............................................................................26

AC Power Line Transient Protection 1

Data Line Transient Protection 2

vii

Revision Record

Issue Date Remarks

A Sept 02 First issue

viii

Radio Frequency Interference Statements

Federal Communications Commission (FCC)

Information to User

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

NCR is not responsible for any radio or television interference caused by unauthorized

modification of this equipment or the substitution or attachment of connecting cables

and equipment other than those specified by NCR. The correction of interference

caused by such unauthorized modification, substitution or attachment will be the

responsibility of the user. The user is cautioned that changes or modifications not

expressly approved by NCR may void the user’s authority to operate the equipment.

Canadian Department of Communications

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le

Règlement sur le brouillage radioélectriques édicté par le ministrère des

Communications du Canada.

Voluntary Control Council for Interference (VCCI)

Table des matières

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

Prestel

Prestel VCS-G2PRO Manuel utilisateur