Wali M002LM Manuel utilisateur

M002LM

WARNING

！

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.

Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect

assembly or inappropriate use.

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

Measure the thickness of your mounting surface or desk

Option A : Clamp Installation Option B: Grommet Base Installation

4A 4B

1 2

Dual Monitor Desk Mount

75x75\100x100

VESA Plate

A (x2)

Arm

B (x1)

C-Clamp

C (x1)

Pole

D (x1) Pole Cover

E (x1)

Tool Holder

F (x1)

Grommet Base Plate

G (x1)

Anti-skid Pad

J (x5)

M3x7 Bolt

I (x2)

Nut

H (x2)

M6x12 Bolt

K (x3)

Support Plate

L (x1)

Allen Key 4mm

M (x1)

Allen Key 6mm

N (x1)

Allen Key 5mm

O (x1)

M4x12 Bolt

M-A (x8)

M4x16 Bolt

M-B (x8)

M5x12 Bolt

M-C (x8)

M5x16 Bolt

M-D (x8)

D5 Washer

M-E (x8)

Spacer

M-F (x8)

Fit clamp: 0.39”- 3.3”

Grommet: 0.39”- 3”

C-Clamp Brace

Clamp

M0.39”-3.3”

Hand knob

Press Pole Cover Einto the top of Pole D.

1.Connect Pole Dand C-Clamp Brace from the bottom using M6x12 Bolt Kand tighten

with Allen Key 4mm M.Tear off the protect paper and attach Anti-Skid Pads Jto the

bottom designated position of C-Clamp Brace as image shown.

2. Connect C-Clamp to C-Clamp Brace using the bolts and tighten with Allen Key 4mm M.

Rotate the hand knob clockwise to fasten for stability.

1. Loosen the screw to release the hand

knob using a screwdriver as image shown.

(Screwdriver not included)

2. Tear off the protect paper and attach Anti-Skid

Pads Jto the bottom designated position of

Grommet Base Plate Gas image shown.

Loosen the bolts on C-Clamp Cusing Allen Key 4mm M.

INSTALLATION MANUAL

1-844-SATTLER (18447288537)

[email protected]

www.walielectric.com

8kg/17.6lbs

RATED

MAX 27”

TIPOVER WARNING

● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.

● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

Supplied Parts List

Manually swivel, tilt, and rotate the monitor for the best viewing angle. Adjust the height of VESA

Plate Ausing Allen Key 6mm N.

Guide the cable through the Tool Holder Fand wire clips. Store the Allen Keys in the Tool

Holder F.

For safety, please do not extend the arms too far forward or backward. This may cause

instability and tip over.

3a.Existing Grommet Hole Installation 3b.Self-drilled Grommet Hole Installation 5

0.39”-3”

ø 10mm

(ø ")3/8

M4x12 M5x12

Hand thread screws

into the threaded

inserts on the back of

your TV to determine

which screw diameter

(M4x12 or M5x12) to use.

M-C M-A

M-E M-E

M-E

M-F

M-B

M-D A

Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at

the marked position through the mounting surface. Place the Grommet Base Plate Gand

Pole Dto the grommet hole. Insert the hand knob through the center hole of Support Plate

Land desk hole, rotate the hand knob clockwise to fasten for stability.

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface

before installing the desk mount. Place the Grommet Base Plate Gand Pole Dto the

grommet hole. Insert the hand knob through the center hole of Support Plate Land desk hole,

rotate the hand knob clockwise to fasten for stability.

Put the Tool Holder Fand Arm Bthrough the Pole D, adjust the preferred height and

tighten using Allen Key 6mm N.

Put the assembled TV/Monitor onto the Arm Band ensure stability.Tighten the VESA plate

using Nut Hand M3x7 Bolt Iwith a screwdriver. Adjust the tilt angle using Allen Key 6mm N.

(Screwdriver not included)

0.39”-3”

Step 5.1

Select TV Screws

Step 5.2

Select Spacers ( if needed )

Step 5.3a

Step 5.3b

Select M4x12 Bolt M-A or M5x12 Bolt M-C according to your TV/Monitor, connect

VESA Plate Atogether with D5 Washer M-E into the mounting holes on the back of

TV/Monitor, tighten with a screwdriver. (Screwdriver not included)

Select M4x16 Bolt M-B or M5x16 Bolt M-D according to your TV/Monitor, connect

VESA Plate Atogether with D5 Washer M-E and Spacer M-F into the mounting

holes on the back of TV/Monitor, tighten with a screwdriver. (Screwdriver not included)

Flat Back Monitor

Curved Back Monitor

0.8” Height Adjustment

Note: Please make sure two arms are aligned and balanced.

Autres manuels Wali Support et étagère

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur