Wali M00LP Manuel utilisateur

2. Remove the screw, washer and top plate from the M10 Hand Knob m , then connect the M10 Hand

Knob m and C-clamp b with the screw, washer and top plate that were just removed.

Select the preferred height according to your desk thickness. Connect C-clamp b to C-clamp Brace c

using M8x12 Bolt g , and tighten with Allen Key 5mm i . Rotate the Hand Knob m clockwise to fasten

for stability.

M00LP/M00LP-W

Laptop Tray Desk Mount

75x75\100x100

INSTALLATION MANUAL

1-844-SATTLER (18447288537)

[email protected]

www.walielectric.com

(10kg/22lbs)

RATED

WARNING

！

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.

Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect

assembly or inappropriate use.

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

TIPOVER WARNING

Supplied Parts List

Laptop : 17'' Max

Monitor：27'' Max

Option A : Clamp Installation

1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and

tighten with Allen Key 3mm o .

Option B : Grommet Base Installation

1. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14 Bolt

and tighten with Allen Key 3mm .

Stick the EVA pad B to

the C-Clamp Brace c

3mm

Wire Clip

l (x2)

Wire Clip

k (x1)

Grommet Base Plate

q (x1)

Support Plate

p (x1)

M10 Hand Knob

m (x1)

EVA Pad A

n (x1)

EVA Pad B

o (x1)

Pole

a (x1)

VESA Plate

e (x1)

M5x14 Bolt

f (x3)

M4x12 Bolt

j (x4)

Swivel Arm

d (x1)

Anti-skid Pad

u (x4)

M4x12 Bolt

s (x4)

Laptop Tray

r (x1)

D4 Nut

t (x4)

C-Clamp

b (x1)

C-Clamp Brace

c (x1)

Stick the EVA pad A o to

the Grommet Base Plate

v (x1)

Wrench

M6 Nut

h (x1)

M8x12 Bolt

g (x2)

Allen Key

i (x1)

6Manually swivel, tilt, and rotate the tray for the best viewing angle.

5Guide the cable through the Wire Clips ( h , i ) and store the Allen Keys o in the

Wire Clip . Adjust the tilt angle using Allen Key 5mm n .

15°

Put the Wire Clip h and Swivel Arm c through the Pole a , adjust the preferred height and

tighten using Allen Key 6mm o . Attach the Wire Clips l to the Swivel Arm c .

Option A : Laptop Tray Installation

Using M4x12 Bolt u and D4 Nut v to attach the VESA Plate e to the Laptop Tray r and

tighten with a screwdriver. Put the Anti-skid Pad u on the designated position on the tray.

(Screwdriver not included)

Option B : Monitor Mount Installation

Laptop Tray Holder

Notice: For safety, please remove your laptop when making adjustments.

Remove the screw, washer and top plate from the M10 Hand Knob m . Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm)

diameter hole at the marked position through the mounting surface.

Position the Pole a on the mounting surface and connect the hand knob mthrough the Support Plate p and the self-drilled hole with the Pole a .

Rotate the hand knob mclockwise to fasten for stability.

Remove the screw, washer and top plate from the M10 Hand Knob m . If the existing grommet hole comes with a plastic protector, remove it to

ensure a flat surface before installing the desk mount.

Position the Pole a on the mounting surface and connect the hand knob Nthrough the Support Plate p and the grommet hole with the Pole a .

Rotate the hand knob Nclockwise to fasten for stability.

2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole Installation

ø 10mm

(ø ")3/8

Notice: Please make sure the security nut

is installed before you rotate the monitor/laptop.

Put the assembled laptop tray onto the Swivel Arm d and install the security M6 Nut h as the

image shown. Tighten the M6 Nut h

using the Wrench for stability.

Ce manuel convient aux modèles suivants

Autres manuels Wali Support et étagère

Wali

Wali SON003-W Manuel utilisateur

Wali

Wali MF003 Manuel utilisateur

Wali

Wali MF002 Manuel utilisateur

Wali

Wali CS203 Manuel utilisateur

Wali

Wali TVDVD-01 Manuel utilisateur

Wali

Wali SBR201 Manuel utilisateur

Wali

Wali M001LM Manuel utilisateur

Wali

Wali MATI001-G Manuel utilisateur

Wali

Wali M003S Manuel utilisateur

Wali

Wali STT001D-B Manuel utilisateur

Wali

Wali SWM-EH-01B Manuel utilisateur

Wali

Wali CS201 Manuel utilisateur

Wali

Wali PTT007T-B Manuel utilisateur

Wali

Wali GSDM003S Manuel utilisateur

Wali

Wali MF001-P Manuel utilisateur

Wali

Wali M002XLS Manuel utilisateur

Wali

Wali TVF001XL Manuel utilisateur

Wali

Wali GSMP002 Manuel utilisateur

Wali

Wali CS202 Manuel utilisateur

Wali

Wali M001-W Manuel utilisateur

Wali

Wali GSDM002-P Manuel utilisateur

Wali

Wali TVDVD-5 Manuel utilisateur

Wali

Wali GSDM001-P Manuel utilisateur

Wali

Wali MF002XLS Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur