Ubiquiti PBM3 Manuel utilisateur

Carrier-Class

airMAX®BaseStation

Models:

PBM3, PBM365, PBM5

Introduction

Thank you for purchasing the Ubiquiti Networks™

PowerBridge™M. This Quick Start Guide is designed to guide

you through the installation, and show you how to access the

airOS® Configuration Interface. This Quick Start Guide also

includes the warranty terms and is for use with the following

models:

Model Operating Frequency

PowerBridgeM3 3300 - 3700 MHz

PowerBridgeM365 3650 - 3675 MHz

PowerBridgeM5 Worldwide: 5170 - 5875 MHz

USA: 5745 - 5850 MHz

Package Contents

PowerBridgeM Pole Brackets

(Qty. 2)

Pole Clamps

(Qty. 2)

Carriage Bolts

(M8X135,

Qty. 4)

Carrier-Class

airMAX™BaseStation

Models:

PBM3, PBM365, PBM5

Flange Bolts

(M8X20,

Qty. 4)

Flange Nuts

(M8, Qty. 4)

PoE Adapter

(24V, 1A)

Power Cord Quick

Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Ports

Ethernet Port

(10/100) Mbps

Reset

Button

Port Cover U-Brackets

Ethernet Port The Ethernet port is a 10/100 Mbps port used

for data and supplies power to the PowerBridgeM. Power can

be provided by any of the following:

• PoE adapter (included)

• Ubiquiti Networks TOUGHSwitch™PoE

• Ubiquiti Networks EdgeRouter™PoE

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the

PowerBridgeM is already poweredon.

LEDs

Power The Power LED will light green when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light red when the wireless signal

strength is above -94 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light green when the wireless signal

strength is above -65 dBm.

Installation Requirements

• 13 mm or ½" wrench

• Flathead screwdriver

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Installation

To install the PowerBridgeM, perform the following steps:

1. The Port Cover is hinged to the PowerBridgeM and locked

with a screw. Use a flathead screwdriver to turn the locking

screw counter-clockwise until it is loose. Open the cover by

sliding it down and raising it up.

*720-00065-02*

720-00065-02

2. Connect an Ethernet cable to the Ethernet Port.

3. Close the Port Cover and lock it in place by turning the

locking screw clockwise.

4. Insert two Carriage Bolts into each Pole Bracket.

5. Connect the Pole Brackets to the U-Brackets using the four

Flange Bolts.

6. Mount the PowerBridgeM to the pole:

a. Position the Carriage Bolts around the pole at the

mounting location.

b. Slide a Pole Clamp onto each pair of Carriage Bolts.

c. Hand-tighten a Flange Nut on each Carriage Bolt.

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

7. Rotate the PowerBridgeM to the correct azimuth towards

the other end of the wireless link.

8. Adjust the elevation angle as needed:

a. Loosen the four Flange Bolts on the U-Brackets.

b. Adjust the PowerBridgeM to the desired elevation tilt.

c. Tighten all bolts and nuts to approximately

25 N-m (18 lb-ft).

Flange

Bolts

Powering the PowerBridgeM

The PowerBridgeM can be powered by the included PoE

Adapter or any of the following compatible PoE switches:

• TOUGHSwitch PoE, model TS-5-POE

• TOUGHSwitch PoE PRO, model TS-8-PRO

• EdgeRouter PoE, model ERPoe-5

Connecting to the PoE Adapter

1. Connect the other end of the Ethernet cable from the

PowerBridgeM to the Ethernet port labeled POE on the

PoEAdapter.

2. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the PoE Adapter.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ubiquiti Matériel réseau

Ubiquiti

Ubiquiti UBB Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam M5 Manuel utilisateur

Ubiquiti

Ubiquiti airVision-C Manuel utilisateur

Ubiquiti

Ubiquiti UniFi US-24-250W Manuel utilisateur

Ubiquiti

Ubiquiti 0810354025402 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Cloud Key Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam M PBE-M2-400 Manuel utilisateur

Ubiquiti

Ubiquiti RocketDish RD-5G30 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi NVR Manuel utilisateur

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Manuel utilisateur

Ubiquiti

Ubiquiti UF-OLT-4 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manuel utilisateur

Ubiquiti

Ubiquiti uFiber OLT 4 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi US-24-250W Manuel utilisateur

Ubiquiti

Ubiquiti UBB Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UAP Manuel utilisateur

Ubiquiti

Ubiquiti PowerBeam airMAX AC Gen2 PBE-5AC-Gen2 Manuel utilisateur

Ubiquiti

Ubiquiti Rocket R5AC-Lite Manuel utilisateur

Ubiquiti

Ubiquiti UniFi LED ULED-AT Manuel utilisateur

Ubiquiti

Ubiquiti UniFi US-48-500W Manuel utilisateur

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Manuel utilisateur

Ubiquiti

Ubiquiti PBE-5AC-GEN2-5-EU Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur