Tripp Lite SmartOnline SU1000RT2UHV Manuel utilisateur

1111 W. 35th Street

Chicago, IL 60609 USA

Customer Support: (773) 869-1234

www.tripplite.com

Installation: p. 3 - 5

Basic Operation: p. 6 - 9

Storage & Service: p. 11

Specifications: p. 11 - 12

Important Safety Instructions: p. 2

Owner's Manual

SMARTONLINE™

Rack/Tower Mount

Online UPS Systems

ESPAÑOL: p. 13

FRANÇAIS: p. 25

DEUTSCH: p. 37

Battery Replacement: p. 10

CUS

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions and warnings that should be

followed while installing, operating & storing all Tripp Lite UPS Systems.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive

contaminants, dust or direct sunlight.

• For best performance, keep the indoor temperature between 32° F and

104° F (between 0° C and 40° C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS to a properly grounded AC power outlet. Do not remove or

modify the ground connector of your UPS's plug. Do not use two-prong

adapters with the UPS's plug.

• Do not plug your UPS into itself; this will damage the UPS and void your war-

ranty.

• If you are connecting your UPS to a motor-powered AC generator, the genera-

tor must provide clean, filtered computer-grade output.

Equipment Connection Warning

• Do not use Tripp Lite UPS Systems for life support applications in which

a malfunction or failure of a Tripp Lite UPS System could cause failure or

significantly alter the performance of a life-support device.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS

except to replace batteries. There are no user-serviceable parts inside.

• Battery replacement should be performed by qualified service personnel.

Because the batteries present a risk of electrical shock and burn from high

short-circuit current, service personnel should observe proper precautions.

Use tools with insulated handles, remove all metal hand jewelry and when

possible work with only one hand to reduce the danger of shock. Replace the

existing batteries with an equal number of new batteries of the same type. Do

not open the sealed lead-acid batteries. Do not short or bridge the battery ter-

minals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal require-

ments or in the USA only call 1-800-SAV-LEAD (1-800-728-5323) for com-

plete recycling information. Do not dispose of the batteries in a fire.

• The UPS contains its own energy source (battery). The output terminals may

be live even when the UPS is not connected to an AC supply.

• Only connect Tripp Lite battery packs of the correct voltage to your UPS’s

external battery connectors.

• Do not connect or disconnect external battery packs while the UPS is operat-

ing from battery.

• Do not operate your UPS without batteries.

Mounting

Rackmount

1) Loosen the wingnuts on each of the

two UPS Side Supports; adjust the

length of the supports to match the

depth of your rack; tighten wingnuts.

2) Mount both UPS Side Supports in

your rack on the inside surfaces of the

rack rails.

Note: Both support ledges should face inward. The side

supports' front and back holes are threaded and do not

require nuts to secure rack bolts.

3) Attach mounting ‘ears’ to the front

end of the UPS’s sides using the screws

provided.

4) Lift UPS and slide it onto the UPS

Side Supports within your rack. Mount

the UPS by screwing rack bolts through

the UPS mounting ‘ears’, through the

rack rails and through the UPS Side

Supports.

Note: The side supports' front holes are threaded and do

not require nuts to secure rack bolts.

Vertical Tower Mount

1) Cover the rackmount screw holes on

the UPS's sides with supplied snap-in

hole-cover caps.

2) Place the UPS upright in a flat, sta-

ble location with its control panel on

the high corner facing forward. Position

stabilizer feet 4 in. from each end of the

UPS.

Installation

SU2200RT2U Shown

Connection & Start-Up

Plug your UPS's Line

Cord into an electrical

outlet.

If your model features a detachable line cord,

first plug the female end into your UPS’s AC

Input Receptacle.

Your UPS must be connected to a dedicated

circuit of sufficient amperage—check the

“Recommended Utility Amps” rating of your

model in the specifications. Note, however,

that the select models may be fitted with differ-

ent plug types. Refer to the “OP Rating/Plug

Rating” chart printed on the top of your UPS.

Once your UPS is plugged in, the fan and all

Indicator Lights will turn ON. The “LINE” and

“LOAD ACTIVE METER” LEDs will illuminate

and the UPS will emit a beep to indicate nor-

mal operation. However, power is not supplied

to your UPS's AC outlets until the UPS is turned

on.

Plug your equipment into

your UPS.

Your UPS is designed to support computer

equipment only. You will overload your UPS if

you connect household appliances or laser

printers to the UPS's outlets.

Turn your UPS ON:

• Press the “ON/TEST”

Switch

• Hold it for several

seconds until you

hear a beep

• Release it

Your UPS will begin providing AC power to its

outlets. The "ON LINE" LED will illuminate.

SU2200RT2U Plug (NEMA 5-20) Shown

SU2200RT2U Shown

Your UPS will function properly without

these connections.

Serial Port Connection

Using the serial cable provided, connect a seri-

al port on your computer to the serial port of

your UPS. Install Tripp Lite's PowerAlert soft-

ware (provided on CD) on the computer .

External Battery Pack

Connection

Check to ensure that the external batteries you

are connecting match the voltage listed on your

UPS’s battery connector. Plug either end of the

battery connection cable (supplied with the bat-

tery pack) into the UPS’s External Battery

Connector and the other end into the Battery

Output Connector on the rear panel of the

external battery pack.

Since your UPS has internal batteries, external

batteries are only needed to extend runtime.

Adding external batteries will increase recharge

time as well as runtime. Make sure that each

end of the cable is fully inserted into its con-

nector. Several small sparks may result during

battery connection; this is normal.

Optional Connections

SU2200RT2U Shown

Basic Operation

“ON/TEST” Switch: This switch controls four separate UPS functions:

UPS Power ON

To turn the UPS on, press this switch, hold it for several seconds until

you hear a beep, then release it. The “ON LINE” LED will illuminate.

UPS Self-Test

During normal on-line operation, press this switch and hold it until you

hear a beep. This initiates a 10-second self-test of the battery. The UPS

will shift to battery power (the “ON BATT” and “BATT ACTIVE METER”

LEDs will illuminate) for ten seconds.

Alarm Silence

To silence the UPS “on-battery” alarm, press this switch and hold it until

you hear a beep.

UPS Cold Start

To use your UPS as a stand-alone power source when AC power is

unavailable (i.e. during a blackout), press this switch and hold it until

you hear a beep. The UPS will then provide battery power to its out-

lets.*

* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating from battery power.

“OFF” Switch: This switch turns power OFF at the UPS receptacles.

Press this switch, hold it until you hear a beep, then release it. The UPS

will continue charging and the fan will continue to cool internal com-

ponents even after you turn the UPS receptacles off. To turn the UPS

OFF completely, including the charger, disconnect the UPS’s power cord

after pressing the “OFF” switch.

“ON LINE” LED: This green light will illuminate constantly to indicate

the UPS is performing normal on-line operation (filtering and resyn-

thesizing incoming AC line voltage to provide pure sine wave output).

When this light is illuminated, you can monitor the load level of your

UPS on the “LOAD ACTIVE METER” LEDs.

“LINE” LED: This green light will illuminate constantly to indicate the

utility supplied AC line voltage at your wall outlet is nominal. It will

flash if the line voltage is outside the nominal range (either too low or

two high). No action is required on your part when the LED flashes; the

UPS continuously and automatically filters AC line power to provide

your equipment with pure sine wave AC power, regardless of brownout

or overvoltage conditions. If this light is off, then AC line voltage is not

present (blackout) or is at an extremely high voltage, and the UPS will

provide connected equipment with power from battery.

Front Panel Switches

Front Panel Indicator Lights

“BYPASS” LED: This yellow light will illuminate to indicate that the

UPS’s DC/AC inverter is deactivated and the UPS is in the “Bypass”

mode. During normal operation this LED will light briefly when the

unit is plugged in, but if an internal fault occurs this light will illumi-

nate constantly to show that connected equipment will receive filtered

AC mains power, but will not receive battery power during a blackout.

In this case, contact Tripp Lite for service.

“FAULT” LED (Select Models Only): This red light will flash when

your UPS detects an internal fault (overheating, overvoltages, etc.) or

when it detects a wiring fault in your wall outlet (reversed phases,

missing ground, etc.) If the light persists after restarting the UPS, con-

tact an electrician to check the AC line. Your UPS will identify the

presence of most (but not all) wiring faults.

“LOAD ACTIVE METER” LED: This green light will illuminate when

your UPS is receiving AC power to indicate that the set of four dual-

function LEDs is displaying the load level of your UPS.

“BATT ACTIVE METER” LED: This green light will illuminate when

your UPS is operating from battery power to indicate that the set of

four dual-function LEDs is displaying the battery charge level of your

UPS. Note: the “ON BATT” LED will also be illuminated.

“OVERLOAD” LED: This red light will illuminate constantly to indi-

cate that your UPS’s capacity has been exceeded while it is in on-line

operation. The UPS alarm will beep continuously. Immediately

remove overload until light and alarm goes off. If you do not immedi-

ately remove the overload, the UPS will transfer from on-line to

bypass operation.

“BATT LOW” LED: This yellow light will illuminate when your UPS’s

battery charge level is low. The UPS alarm will beep until either the

battery charge is depleted or the batteries are adequately recharged.

“ON BATT” LED: This green light will illuminate constantly to indicate

that AC line voltage is not present and your UPS is providing your

equipment with battery power. The UPS will also beep every two sec-

onds, unless silenced by the “ON/TEST” Switch. When this light is

illuminated, you can monitor the battery charge level of your UPS on

the “BATT ACTIVE METER” LEDs.

“REPLACE BATT” LED: This red light will illuminate constantly and

the UPS alarm will sound three beeps* if your UPS’s microprocessor

detects a battery fault or if your UPS fails the automatic self-test (after

you turn your UPS ON) and the UPS battery is less than fully charged.

Turn the UPS OFF and let it charge for 12 hours and turn it back ON

to perform a second self test. If the light continues to stay on, contact

Tripp Lite for service.

*After the initial alarm, the UPS will beep once every hour until the problem is corrected.

Front Panel Indicator Lights (Continued)

Rear Panel

Accessory Slot: Remove the small cover panel from this slot to use

optional accessories to remotely monitor and control your UPS.

Contact Tripp Lite Customer Support at (773) 869-1234 for more

information, including a list of available SNMP, network management

and connectivity products.

“SMART” Serial Port: This serial port connects your UPS to any work-

station or server. Use with Tripp Lite software and cabling to monitor

and manage network power and automatically save open files and shut

down equipment during a blackout. The port uses RS-232 communi-

cations to transmit UPS and power conditions. Contact Tripp Lite

Customer Support at (773) 869-1234 for more information, including

a list of available SNMP, network management and connectivity prod-

ucts.

External Battery Pack Connector: Use to connect optional Tripp Lite

Battery Packs for additional runtime. Contact Tripp Lite Customer

Support at (773) 869-1234 for the appropriate Tripp Lite battery pack

to connect. Refer to instructions available with the Battery Pack for

complete connection information and safety warnings.

Fan: The fan cools the UPS’s internal components. It is always on when

line power is present.

TVSS Cover Plate (Reserved for future use): Optional modem/network

surge protection modules may be available for purchase by special

arrangement with Tripp Lite.

Input Circuit Breaker Switch: This resettable breaker prevents high

input current from damaging the UPS or the attached load. If this

breaker trips, make sure your UPS is connected to AC power of the

proper voltage before resetting the circuit breaker by pushing the

breaker switch in.

Input Receptacle (Select Models Only): Connect one end of the detach-

able line cord into this receptacle and the other into your wall outlet.

Rear Panel (Continued)

Output Circuit Breakers Switches (Select Models Only): These reset-

table circuit breakers protect your UPS from output overload. If one

or both breakers trip, remove some of the load on the circuit(s) and

allow the UPS to cool before pressing the breaker switch(es) in to

reset.

Input Cord (Select Models Only): This permanently attached power

cord connects your UPS to a power outlet.

AC Receptacles (NEMA 5-15R) (Varied by Model):

These 15-, 20- and 30-amp receptacles provide your connected

equipment with pure sine-wave AC output from the AC line during

normal operation and from battery power during blackouts and

severe brownouts. Power provided at these outlets is filtered to pro-

tect connected equipment against damaging surges and line noise.

The receptacles are divided into numbered load banks, as labelled

on the unit. Using PowerAlert software and cabling, load banks one

and two may be individually turned off and on from a remote loca-

tion, allowing users to reset or reboot connected equipment. See

Serial Port Connection under Optional Connections.

NEMA 5-15R

NEMA 5-15/20R

Under normal conditions, the original battery in your UPS will last several years.

Contact Tripp Lite for information about replacement batteries.

Battery replacement should be performed only by qualified service personnel.

The batteries are hot-swappable: it is not necessary to turn off or disconnect the

UPS and its connected load to replace the UPS’s batteries. However, when it is

convenient to do so, service personnel may simplify the replacement procedure

by pressing the OFF switch to turn power off at the UPS outlets and disconnect-

ing the UPS’s power cord from the wall outlet.

When replacing the batteries, qualified service personnel should refer to “Battery

Warnings” in the Safety section and follow this procedure:

1) Place the UPS horizontal with the Control Panel on the right side.

2) Remove both snap-on cover panels (A).

3) Unscrew and remove rack handle plates (B) on either side of the UPS.

4) Disconnect the microprocessor circuit board plug (C) located on the right

side of the UPS.

5) Disconnect battery connectors (D). Note: while batteries are disconnected,

the UPS will not provide battery backup.

6) Unscrew and remove the battery retaining bracket (E).

7) Grasp pull-tab and pull out sliding battery tray (F). WARNING! On the

SU2200RT2U, the batteries are arranged in an “L” shape on the tray. Since

the tray is heaviest on the front and on the left, provide adequate support

to keep the tray from tipping.

8) Make a detailed sketch of the batteries and the polarity, color and connec-

tion of all cables. Disconnect used batteries and dispose of them properly.

Connect replacement batteries in exactly the way original batteries were

connected. Reassemble the UPS by reversing steps 1-7. Note: you may not

receive full runtime until your replacement batteries have fully charged.

Small sparks arcing between battery connectors during battery replacement

are normal.

Battery Replacement

SU2200RT2U SHOWN

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite SmartPro SMART1500RMXL2Ua Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART3000RMXL2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro 3U Manuel utilisateur

Tripp Lite

Tripp Lite BC Internet Manuel utilisateur

Tripp Lite

Tripp Lite SUINT1000LCD2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU10KRT1X Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU80KTV Guide d'installation

Tripp Lite

Tripp Lite Keyspan TuneView BC Pro Manuel utilisateur

Tripp Lite

Tripp Lite OMNISMART1400HG Instructions d'installation et d'utilisation

Tripp Lite

Tripp Lite INTERNET350U Manuel utilisateur

Tripp Lite

Tripp Lite SMART1500CRMXL Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU3000XL Manuel utilisateur

Tripp Lite

Tripp Lite 1400VA Manuel utilisateur

Tripp Lite

Tripp Lite UPS System AVRX550U Manuel utilisateur

Tripp Lite

Tripp Lite SM1000RMNAFTA Manuel utilisateur

Tripp Lite

Tripp Lite OmniSmart OMNISMART1050 Manuel utilisateur

Tripp Lite

Tripp Lite AVR750U Manuel utilisateur

Tripp Lite

Tripp Lite BCINTERNET500 Manuel utilisateur

Tripp Lite

Tripp Lite AGBC5755 Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU2200XLNAFTA Manuel utilisateur

Tripp Lite

Tripp Lite SUPDM11 Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART1500RMXL2Ua Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMX700HG Manuel utilisateur

Tripp Lite

Tripp Lite SM3000RMNAFTA Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur