TRENDnet TEG-448WS - Switch Manuel utilisateur
TEG-448WS
Quick Installation Guide
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
3
2
6
1. Before You Start
2. Hardware Installation ........................................................................
3. Web Management Utility ....................................................................
................................................................................
Table of Contents
Version 01.10.2007
System Requirements
Application
TEG-448WS
Quick Installation Guide
Utility and User Guide CD-ROM
2 mounting brackets with screws
Rubber Cushions
AC Power Cord
Web Browser: Internet Explorer (5.0 or above)
Computer with Network adapter installed
Optional 4 Mini-GBIC Modules (e.g. TEG-MGBSX, TEG-MGBS10)
Package Contents
1. Before You Start
English
1
1000Mbps
Multi-Mode Mini
GBIC Module
(TEG-MGBSX)
Multi-Mode Mini
GBIC Module
(TEG-MGBSX)
Workstations with 10/100Mbps
Fast Ethernet PCI Adapter
(TE100-PCIWN)
Serverss with
Copper Gigabit PCI Adapter
(TEG-PCITXR)
48-Port 10/100/1000Mbps Gigabit Web Smart Switch
(TEG-448WS)
Cable/DSL 4-Port
Broadband Router
(TW100-S4W1CA)
Internet
26-Port Gigabit Web Smart Switch
(TEG-224WSplus)
Workstations with
Copper Gigabit PCI Adapter
(TEG-PCITXR)
VLAN Group 2VLAN Group 1
Cable/DSL
Modem
LC Type Cable
2. Hardware Installation
English
2
2. Connect a CAT-5 network
cable from the computer to an
available Ethernet port of the
TEG-448WS.
1. Connect the Power Cord to the
rear of the TEG-448WS and
then to a power outlet.
Note: After hardware installation is complete, use the Web-based Smart Utility
to configure the TEG-448WS. To access the Web-based Smart Utility, open
your web browser, and enter the default IP Address and
default password "admin". Make sure your computer and the TEG-448WS are
configured to the same network segment.
http://192.168.0.1
English
3
3. Click Start > Programs >
web_management_utility, and
then click
web_management_utility.
3. Web Management Utility
For Windows User
1. Insert the Utility CD-ROM into
your computer's CD-ROM Drive
and then click Install Utility.
2. Follow the Installation Wizard
instructions. Click OK.
Note: If you would like to easily discover all the Web Management Switches on
the network, assign IP Address, change the password, and upgrade to new
firmware, then install the Web Management Utility. Follow the steps below.
English
4
4. Click Discovery, and then double-
click the Switch that appears in
the Discovery List.
5. Click the Switch in the Monitor
List and then click Configuration
setting.
6. Configure the IP Address, Subnet
mask, Gateway, and Password.
Click Set.
English
5
7. Click OK.
8. Click Access web.
9. Type in your Password and then
click Login.
For more information regarding the TEG-448WS configuration and advanced
settings, please refer to the User's Guide included on the Utility CD-ROM or
TRENDnet's website at www.trendnet.com
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
After connecting the TEG-448WS to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the TEG-448WS and the power
outlet. Also check that the power outlet is receiving power.
After installing the Web-Management Utility, I clicked Discovery and the Utility
is unable to discover the TEG-448WS. What should I do?
Make sure that the TEG-448WS is powered on and that all connections are
secure. Also check that your computer's IP address is on the same network
segment as the TEG-448WS. The default IP address of the TEG-448WS is
http://192.168.0.1 and the default password is "admin".
When I access the TEG-448WS using a web browser, I get a screen that tells
me “only one user can login”. What should I do?
Another computer is configuring the TEG-448WS. Please wait until the user
logs off. If the other user has already logged off and you still get the same screen,
then disconnect the power cord from the TEG-448WS, wait for 5 seconds,
reconnect the power cord to the TEG-448WS, allow 5 seconds for the Switch to
power on, and then attempt to access the web configuration page to login.
I forgot the administration password. How do I reset my TEG-448WS?
Press on the reset button using a pen or paperclip for 10 seconds. The
default password is admin.
If you still encounter problems or have any questions regarding the TEG-448WS, please
refer to the User's Guide included on the Utility CD-ROM or contact TRENDnet's
Technical Support Department.
6
Troubleshooting
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com
TRENDnet Technical Support
US Canada
24/7 Tech Support
Toll Free Telephone: 1(866) 845-3673
Europe (Germany France Italy Spain Switzerland UK)
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
Toll Free Telephone: +00800 60 76 76 67
.
. . . . .
Copyright ©2007. All Rights Reserved. TRENDnet.
20675 Manhattan Place
Torrance, CA 90501
USA
.
Autres manuels pour TEG-448WS - Switch
10
Table des matières
Autres manuels TRENDnet Changer
TRENDnet
TRENDnet TPE-3018L Manuel utilisateur
TRENDnet
TRENDnet TK-408K Manuel de la liste des pièces
TRENDnet
TRENDnet TPE-082WS Manuel utilisateur
TRENDnet
TRENDnet TK-400 Manuel utilisateur
TRENDnet
TRENDnet TK-207K - KVM Switch - USB Instructions de montage
TRENDnet
TRENDnet TK-204UK - DVI USB KVM Switch Manuel utilisateur
TRENDnet
TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manuel utilisateur
TRENDnet
TRENDnet TEG-40080ES Manuel utilisateur
TRENDnet
TRENDnet TE100-H24R Manuel utilisateur
TRENDnet
TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manuel utilisateur
TRENDnet
TRENDnet TE100-S16 - DATA SHEETS Manuel utilisateur
TRENDnet
TRENDnet TI-PG80 Manuel utilisateur
TRENDnet
TRENDnet TE-910 Manuel utilisateur
TRENDnet
TRENDnet TE100-SK3 Manuel du propriétaire
TRENDnet
TRENDnet TE-910plus Manuel utilisateur
TRENDnet
TRENDnet TE100-S16 - DATA SHEETS Manuel utilisateur
TRENDnet
TRENDnet TK-200K Manuel utilisateur
TRENDnet
TRENDnet TE100-S5 Manuel utilisateur
TRENDnet
TRENDnet TEG-448WS - Switch Manuel utilisateur
TRENDnet
TRENDnet TU3-H4 Manuel utilisateur
