Texas Instruments CC2543EMs Manuel utilisateur

SWRU315

April 2012

Web sites: www.ti.com/lprf

E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

CC2543-CC2544 Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test Application

1. Kit Contents

2 x SmartRF05 Evaluation Boards (EB)

2 x CC2543 Evaluation Modules (EM)

2 x Pulse W1010 Antennas

1 x CC2544 USB Dongle

Cables

Documentation

The RF boards in this kit are FCC and IC

certified and tested to comply with ETSI/R&TTE

over temperature from 0 to +35°C. The antenna,

W1010 from Pulse, is a ¼ wave dipole antenna

with 2 dBi gain.

Caution! The kit contains ESD

sensitive components. Handle with

care to prevent permanent damage.

2. Hardware Requirements

To run the PER test described in this Quick Start

Guide, you would need either two CC2543EMs

mounted on SmartRF05 Evaluation Boards

(SmartRF05EB - Rev 1.8.1 or later) or one single

CC2543EM mounted on a SmartRF05EB and a

CC2544 Dongle (powered through USB). Both

the dongle and SmartRF05EB are included in the

CC2543-CC2544DK.

More information about the SmartRF05EB can

be found in www.ti.com/lit/swru210.

The CC2543EM boards can also be plugged into

a battery board (see www.ti.com/tool/soc-bb) for

standalone operation.

The source code for the PER test can be

downloaded from the CC2543-CC2544DK

product page (www.ti.com/tool/cc2543-

cc2544dk).

3. Hardware Setup

Connect the antenna to the SMA connector on

the CC2543EM. Tighten the antenna’s screw

firmly on to the SMA connector. If not properly

connected, you might see reduced RF

performance.

Next, mount the CC2543EMs firmly on to

connectors P5 and P6 on the SmartRF05EB.

The CC2544 Dongle can be connected to any

USB port to power the device.

Caution! To minimize risk of injury, avoid

touching components during operation if

symbolized as hot.

4. Power Options

There are several ways of applying power to the

SmartRF05EB.

USB (5V)

2 x 1.5 V AA Alkaline Batteries

External Power Supply (4-20V)

For the batteries, USB and external power supply

via the DC jack, there are voltage regulators on

the EB that will set the on-board voltage to 3.3 V.

Warning! To minimize risk of injury or property

damage, never use rechargeable batteries to power

the board. Always select a power source that is

suitably rated for use with this EVM, not exceeding

20 VDC, with a current output rating between 0 and

1500 mA. Note that there should only be one active

power source at any one time.

5. Power the Boards

Locate the power

source header P11 just

above the LCD on the

EB. Connect pins 1 and

2 if you are using

battery power. Connect

pins 2 and 3 if you are using USB or an external

power supply.

Once you have set P11,

find switch P8 just next to

the DC jack on the EB. To

power up the boards, flip

the switch from the “OFF”

position to “ON”.

Do not leave the EVM powered when

unattended.

6. Start-up Screen

The CC2543EMs and the CC2544 Dongle will

be pre-loaded with a Packet Error Rate (PER)

test application. The LCD screens on the two

SmartRF05EBs should display the messages

below:

A green led (LED2 on CC2544Dongle, LED1 on

SmartRF05EB) will be lit on power on. For a

master device in beacon mode the led will blink

at a slow pace.

7. Choosing Mode

The application can be used between two

CC2543EM’s or between a single CC2543EM

and the CC2544 Dongle. There are two

operating modes: “Remote” and “Master”.

After button S1 is pushed at the start up screen,

the mode selection screen (showed below) will

appear. The Remote mode is shown by default.

Press the joystick up and down to change

between master and remote mode and press

button S1 to confirm. The CC2544 Dongle is set

to master by default as it is the only option for

this device in this application.

In the Remote mode all the parameters for the

current PER test must be set up before the test

begins (go to step 10).

8. Master Mode (Beacon)

In “Master” mode, the radio will repeatedly (once

every 10 milliseconds) send out a “beacon”

signal (250 kbps, GFSK modulation, 160 kHz

deviation, 2402 MHz) and listen for a response

from the remote device. The Green LED1 will

blink continuously.

No more actions are needed from the user for

the master device to work.

9. Master Mode (PER test)

Once the beacon is acknowledged by the

“Remote”, the actual PER test begins. The PER

test configuration is included in the payload of

the acknowledge packet. The Master device

extracts this information and configures the radio

parameters accordingly. During the PER test,

packets are sent at a fixed repetition rate of 10

msec.

During the test the number of sent packets will

be updated on the LCD display as well as the link

status between the Master and Remote device.

10. Frequency Selection

When the Remote mode is chosen, a series of

settings must be configured to set up the link for

the PER test. The frequency must be selected

first (the selectable frequency range is from 2402

MHz to 2480 MHz). Move the joystick up or down

to change the frequency (channel) and press S1

to confirm the choice.

11. Modulation Setup

There are 7 different modulation schemes

available. The different bitrates are 250 Kbps,

500 Kbps, 1Mbps and 2 Mbps. MSK modulation

is available for 250 Kbps and 500 Kbps data rate

while GFSK has all of the mentioned above.

Move the joystick up or down to change the

scheme and press S1 to confirm the choice.

12. Packet Length

The packet length can be set to 10, 16, 32 or 63

bytes. Move the joystick up or down to change

the packet length and press S1 to confirm the

choice.

13. Number of Packets

The total number of packets to be sent for each

run can be set to 100, 1000, 10000, 100000 and

1000000. Move the joystick up or down to

change the number of packets and press S1 to

confirm the choice.

14. LNA Gain

For the 2Mbps data rates the AGC is enabled,

while for lower rates the LNA gain must be set to

HIGH or LOW. Move the joystick up or down to

change between LOW and HIGH gain and press

S1 to confirm the choice. After confirming the last

choice the configuration packet will be sent to the

Master device and the PER test begins.

15. Results I

The packet error rate (PER) is presented as the

sum of lost packets and packets with CRC error

per thousand. The received signal strength

indication (RSSI) is presented as a running

average of the eight last samples. The number of

received packets is continuously updated on the

LCD display while the test is running.

13. Results II

When the test is complete a small downward

facing arrow will show in the bottom right of the

LCD screen. This indicates that the test is

complete and that there is an additional results

screen “below”. Move the joystick up and down

to jump between the two test result screens.

Press the S1 button to exit the test results.

14. Repeat Test

After exiting the test results the user is presented

with two choices. If “Restart Test” is chosen the

same test as previously run will be repeated. The

test can also be restarted at any time during the

test by pushing the S1 button. Move the joystick

up or down to switch between the two commands

and press S1 to confirm the choice.

15. New Test

If “New Test” is chosen the application will return

to setting up the configuration for a new test,

starting at frequency selection. The test can also

be stopped at any time during the test by pushing

on the joystick like a button.

Additional Tools and Links

SmartRF™Studio

SmartRF Studio allows you to configure the radio,

run RF performance tests, and run link tests

between two SmartRF05EBs with CC543EMs.

SmartRF Studio can be downloaded from

www.ti.com/smartrfstudio

SmartRF Flash Programmer

Texas Instruments has a simple tool which can

be used to program the flash on the CC2543

and CC2544 devices.

SmartRF Flash Programmer can be

downloaded from www.ti.com/tool/flash-

programmer

IAR Embedded Workbench

To develop software, program, and debug the

CC2543 and CC2544, you should use IAR

Embedded Workbench for 8051.

More information on IAR EW8051, including a

free evaluation version download, can be found at

www.iar.com/ew8051.

Useful Links

CC2543-CC2544DK Product Page:

www.ti.com/tool/cc2543-cc2544dk

CC2543-CC2544DK User’s Guide:

www.ti.com/lit/swru318

CC2543/44/45 User’s Guide:

www.ti.com/lit/swru283

More Useful Links

CC2543 Product Page:

www.ti.com/product/cc2543

CC2544 Product Page:

www.ti.com/product/cc2544

For additional help, visit the TI E2E Forums:

www.ti.com/lprf-forum

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following

conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user

indemnifies TI from all claims arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/ kit may

be returned within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED

WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF

THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide

prior to handling the product. This notice contains important safety information about temperatures and

voltages. For additional information on TI's environmental and/or safety programs, please visit

www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to

any machine, process, or combination in which such TI products or services might be or are used. TI

currently deals with a variety of customers for products, and therefore our arrangement with the user is not

exclusive. TI assumes no liability for applications assistance, customer product design, software

performance, or infringement of patents or services described herein.

Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may

not be subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for

ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not

considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can

radiate radio frequency energy and has not been tested for compliance with the limits of computing devices

pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against

radio frequency interference. Operation of the equipment may cause interference with radio communications,

in which case the user at his own expense will be required to take whatever measures may be required to

correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in

legally allocated frequency and power limits. Any use of radio frequencies and/or power availability of this

EVM and its development application(s) must comply with local laws governing radio spectrum allocation and

power limits for this evaluation module. It is the user’s sole responsibility to only operate this radio in legally

acceptable frequency space and within legally mandated power limitations. Any exceptions to this is strictly

prohibited and unauthorized by Texas Instruments unless user has obtained appropriate

experimental/development licenses from local regulatory authorities, which is responsibility of user including

its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the

user guide with the maximum permissible gain and required antenna impedance for each antenna type

indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for

that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la

conformité ont pu vider l’autorité de l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans

le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le

type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne

énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque

type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain

maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

【Important Notice for Users of this Product in Japan】

This development kit is NOT certified as Confirming to Technical Regulations of

Radio Law of Japan!

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with

respect to this product:

(1) Use this product in a shielded room or any other test facility as defined in the notification #173

issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of

Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan,

(2) Use this product only after you obtained the license of Test Radio Station as provided in Radio

Law of Japan with respect to this product, or

(3) Use of this product only after you obtained the Technical Regulations Conformity Certification as

provided in Radio Law of Japan with respect to this product.

Also, please do not transfer this product, unless you give the same notice above to the transferee.

Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law

of Japan. Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjukku-ku, Tokyo, Japan

http://www.tij.co.jp

【ご使用にあたっての注意】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますの

でご注意ください。

（１）電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた

電波暗室等の試験設備でご使用いただく。

（２）実験局の免許を取得後ご使用いただく。

（３）技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転でき

ないものとします。

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated,

this EVM is not a finished electrical equipment and not intended for consumer use. It is intended solely for

use for preliminary feasibility evaluation in laboratory/development environments by technically qualified

electronics experts who are familiar with the dangers and application risks associated with handling electrical

mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but

not limited to Food and Drug Administration regulations, if applicable) which relate to your products and

which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM

for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all

such laws and other applicable regulatory requirements, and also to assure the safety of any activities to

be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM.

Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the

EVM and any human body are designed with suitable isolation and means to safely limit accessible

leakage currents to minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property

damage, injury or death, even if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing

materials

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and

environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not

limited to input and output voltage, current, power, and environmental ranges) may cause property damage,

personal injury or death. If there are questions concerning these ratings please contact a TI field

representative prior to connecting interface electronics including input power and intended loads. Any loads

applied outside of the specified output range may result in unintended and/or inaccurate operation and/or

possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide

prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please

contact a TI field representative. During normal operation, some circuit components may have case

temperatures greater than 60 C as long as the input and output are maintained at a normal ambient

operating temperature. These components include but are not limited to linear regulators, switching

transistors, pass transistors, and current sense resistors which can be identified using the EVM schematic

located in the EVM User's Guide. When placing measurement probes near these devices during normal

operation, please be aware that these devices may be very warm to the touch. As with all electronic

evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics

normally found in development environments should use these EVMs

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its

licensors and their representatives harmless from and against any and all claims, damages, losses,

expenses, costs and liabilities (collectively, "Claims") arising out of or in connection with any use of the EVM

that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims arise

under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or

expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in

safety critical applications (such as life support) where a failure of the TI product would reasonably be

expected to cause severe personal injury or death, such as devices which are classified as FDA Class III or

similar classification, then you must specifically notify TI of such intent and enter into a separate Assurance

and Indemnity Agreement.

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO

BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH

ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This

notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety

programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and

therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal

Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer

use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will

be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and

power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local

laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this

radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory

authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SPACER

【【Important Notice for Users of this Product in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this

product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with

respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note

that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

http://www.tij.co.jp

【ご使用にあたっての注】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SPACER

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments SimpleLink CC2650 Manuel utilisateur

Texas Instruments

Texas Instruments CC2431ZDK Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad CC1312PSIP Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6725A Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F4152IPM Manuel utilisateur

Texas Instruments

Texas Instruments TIDA-00830 Manuel utilisateur

Texas Instruments

Texas Instruments CC2531 Manuel utilisateur

Texas Instruments

Texas Instruments AM571 Series Manuel utilisateur

Texas Instruments

Texas Instruments SWRU351 Manuel utilisateur

Texas Instruments

Texas Instruments TPS3703 Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0G350 Series Manuel utilisateur

Texas Instruments

Texas Instruments MSP-EXPCC430RF Series Manuel utilisateur

Texas Instruments

Texas Instruments MSP432P401R Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6736 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320DM357 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6726 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6768 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6733 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320 2806 Series Manuel du produit

Texas Instruments

Texas Instruments MSP430 series Manuel utilisateur

Texas Instruments

Texas Instruments MSP43 series Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67781 Manuel utilisateur

Texas Instruments

Texas Instruments TPS929120EVM Manuel utilisateur

Texas Instruments

Texas Instruments LP-MSPM0L1306 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur