Texas Instruments CC110L Manuel utilisateur

SWRU292B

October 2013

Web sites: www.ti.com/lprf

E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

CC11xL 868/915 MHz Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test

1. Kit Contents

2 x SmartRF™Transciever EB (TrxEB)

2 x CC110LEM 868/915 MHz

1 x CC113LEM 868/915 MHz

1 x CC115LEM 868/915 MHz

1 x MSP430 Debug Probe (FET)

2 x Micro USB Cables

1 x Standard USB Cable

1 x 14-pin Flat Cable

The 868/915 MHz RF boards in this kit are FCC and IC certified

and tested to comply with ETSI/R&TTE over temperatures from

0 to +35°C.

FCC/IC Regulatory Compliance

FCC Part 15 Class A Compliant

IC ICES-003 Class A Compliant

(* picture may deviate)

2. TrxEB Overview

Caution! The kit contains ESD sensitive

components. Handle with care to

prevent permanent damage.

3. Plug the EM into the TrxEB

Insert a CC110LEM into the TrxEB. Do not use

excessive force on the EM.

The EM has a PCB antenna, so there is no need

for an external antenna.

You can also use CC113L and CC115L for the Per

test, but note that CC113L is a receiver only and

CC115L is a transmitter only.

4. Select Board Mode

Use the switches S1 and S2 to select the operating

mode of the board. For the sake of this quick start

guide, please select “Enable” and “UART”. This

configuration will make it possible to communicate

directly with the MSP430 over a virtual COM port

on the PC.

5. Power Options

There are several ways of applying power to the

TrxEB.

2 x 1.5V AA Non-Rechargeable Alkaline

Batteries

USB (5V through USB plug)

External Power Supply (requirements below)

MSP430 Debugger

When the power source is batteries or USB, the

voltage regulators on the TrxEB will set the on-

board supply voltage to 3.3VDC.

External Power Supply1Requirements:

Nom Voltage: 3.3VDC

Max Current: 800 mA

Efficiency Level V

Warning! To minimize risk of personal injury or

property damage, never use rechargeable

batteries to power the board.

6. Select Power Source

Depending on the power source, make sure you

connect jumpers to the appropriate pins on the

“Power Source” header. For instance, if you use

batteries, use a jumper to short-circuit pin 1 and 2

on the header. The last jumper in the row (pin 9-

10) should always be mounted, unless the

MSP430 FET is used as the power source.

Note that there should only be one active

power source at any one time. Do not leave the

board powered when unattended.

7. Welcome Screen

Turn on power with the Main Power switch. You

should now see the Texas Instruments logo and a

short description of the buttons on the LCD.

Pushing any of the five buttons on the board will

take you to the main menu.

NB! If you don’t see anything on the screen

make sure the mode switches are in the correct

positions (see step 4 above).

8. Packet Error Rate Test

Select the PER (Packet Error Rate) test by

highlighting the selection using the up/down

buttons. Confirm your selection by pressing Enter

(right button).

9. Select Test Mode

The PER test can be run is several modes. Easy

Mode sets up a one-way test and uses default

settings. This test is convenient for practical range

testing.

The other test modes are described in the “TrxEB

RF PER Test Software Example User’s Guide”,

available on the kit web page.

To proceed, highlight “Easy Mode” and press Enter

(right button).

When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and

safety certification requirements such as UL, CSA, VDE, CCC, and PSE.

Connectors

MSP430

Breakout

USB

Breakout

Main

Power

Switch

Power

Selection

Board Mode

Switches

LCD

Buttons

LEDs

MSP430

Debug

Interface

10. Select Frequency

Select which frequency to use for the test. Make

sure that the evaluation modules you have match

the selected frequency.

11. Select Mode

One of the boards must operate as the slave

(transmitter) and the other as master (receiver).

Select Slave on one board…

…and Master on the other board.

12. Establish Link

The slave node will now wait for a configuration

package from the Master. The configuration

contains the parameters used for the PER test.

The configuration package will be sent when you

select “link devices” on the master node.

13. Link Established

When the initial linking has completed, the slave

node will start the test by continuously transmitting

packets to the master.

14. Start the Receiver (master)

On the master node, you can select the number of

packets you want to receive in order to calculate

the packet error.

When selecting “Start PER Test”, the master

(receiver) will begin to count the number of

received packets and provide some statistics.

15. PER Test Results

The master will display a window that plots the

received signal strength (RSSI) for each packet.

Press the “Up” button to go to the detailed

statistical window.

16. PER Test Results

The statistics window will show the error rate

based on the number of lost or erroneous packets

divided by the total number of packets that should

have been received.

17. Troubleshooting

It you are experiencing problems with this test,

please check the following:

Nothing is shown in the display! Make sure the

mode switches are in the correct positions (see

step 4 above).

Please visit the kit web page and check for

updated SW and documentation. Updated SW

can be downloaded to the device using IAR

EW430 or SmartRF Flash Programmer.

If you get poor PER results at short distances,

try to move the transmitter and receiver further

apart. The CC11xL receiver may experience

saturation if it is too close to the other CC11xL

transmitting at full output power.

18. References

Please visit www.ti.com and

http://www.ti.com/tool/cc11xldk-868-915

On the kit product page, you will find additional

documentation, links to updated software

examples and software tools like SmartRF Studio.

You will also find a lot of information on the TI E2E

forum at http://e2e.ti.com

We hope that you will enjoy working with the

CC110L, CC113L and CC115L devices.

SmartRF™Studio

1. Download and Install

Before connecting SmartRF TrxEB to your PC,

download and install SmartRF Studio from

www.ti.com/smartrfstudio.

2. Launch SmartRF Studio

After installing the tool, connect the EB to the PC

using the USB cable and start SmartRF Studio.

Select the “Sub 1 GHz” tab and double click the

highlighted device icon (CC110L, CC113L or

CC115L).

3. Test the Radio

You can now configure the radio, export register

settings and run performance tests of the radio.

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO

BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH

ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This

notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety

programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and

therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal

Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer

use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will

be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and

power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local

laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this

radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory

authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SPACER

【【Important Notice for Users of EVMs for RF Products in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this

product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with

respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note

that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

http://www.tij.co.jp

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SPACER

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished

electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in

laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks

associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug

Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,

affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable

regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,

contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)

between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to

minimize the risk of electrical shock hazard.

3. Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,

CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine

and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable

safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to

perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the

user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and

environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact

a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the

specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or

interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the

load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures

greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include

but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the

EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please

be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable

in electronic measurement and diagnostics normally found in development environments should use these EVMs.

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives

harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in

connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims

arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such

as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices

which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate

Assurance and Indemnity Agreement.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments DV2031S2 Manuel utilisateur

Texas Instruments

Texas Instruments TMUX646EVM Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F67661 Manuel utilisateur

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuel du produit

Texas Instruments

Texas Instruments MSP430F5638 Manuel utilisateur

Texas Instruments

Texas Instruments C2000 LED BoosterPack Manuel utilisateur

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6767 Manuel utilisateur

Texas Instruments

Texas Instruments CC2533EMK Manuel utilisateur

Texas Instruments

Texas Instruments TDP0604 Manuel utilisateur

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Guide d'installation

Texas Instruments

Texas Instruments MSP430F6735A Manuel utilisateur

Texas Instruments

Texas Instruments CC3235MODASF Manuel utilisateur

Texas Instruments

Texas Instruments MSP432P401R Manuel utilisateur

Texas Instruments

Texas Instruments PurePath CC85XXDK-HEADSET Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F28004x Manuel du produit

Texas Instruments

Texas Instruments TMS370 Series Manuel utilisateur

Texas Instruments

Texas Instruments MSP430FG47x Manuel utilisateur

Texas Instruments

Texas Instruments DRV2605L Manuel utilisateur

Texas Instruments

Texas Instruments MSP430FG6626 Manuel utilisateur

Texas Instruments

Texas Instruments CC1110 Manuel utilisateur

Texas Instruments

Texas Instruments MSP430F6723A Manuel utilisateur

Texas Instruments

Texas Instruments CC1110 Manuel de programmation

Texas Instruments

Texas Instruments MSP430F6726 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur