Texas Instruments CC1125 Manuel utilisateur

SWRU317

March 2012

Web sites: www.ti.com/lprf

E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

CC1125 Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test

1. Kit Contents

2 x SmartRF Transceiver Evaluation Boards

(TrxEB)

2 x CC1125 ETSI Cat1 868 MHz Boards

(CC1125EM-CAT1-868)

2 x W5017 Pulse Antennas

1 x MSP430 Debug Probe (FET)

2 x Micro USB Cables

1 x Standard USB Cable

1 x 14-pin Flat Cable

4 x 1.5 Volt AA Batteries

Documentation

2. TrxEB Overview

3. Plug the EM into the TrxEB

Insert a CC1125EM board into the TrxEB as

shown above. Connect the antenna to the SMA

connector on the EM.

Caution! The kit contains ESD sensitive

components. Handle with care to

prevent permanent damage. To

minimize risk of injury, avoid touching

components during operation if

symbolized as hot.

The hardware in this kit is tested and complies with

ETSI/R&TTE over temperature from 0 to +35°C. The

W5017 whip antenna from Pulse has a gain of 2 dBi.

The CC1125 is a receiver category 1 device, c.f. ETSI

EN 300 220-1, §4.1.1.

4. Select Board Mode

Use the switches S1 and S2 to select the

operating mode of the board. For the sake of this

quick start guide, please select “Enable” and

“UART”. This configuration will make it possible

to communicate directly with the MSP430 over a

virtual COM port on the PC.

5. Power Options

There are several ways of applying power to the

TrxEB.

USB (5V)

2 x 1.5 V AA batteries

External regulated power supply

MSP430 debugger

For the batteries and USB, there are voltage

regulators on the TrxEB that will set the on-board

voltage to 3.3 V.

Warning! To minimize risk of injury or property

damage, never use rechargeable batteries to

power the board. Always select a power source

that is suitably rated for use with this EVM, not

exceeding 3.6 VDC, with a current output

rating between 0 and 500 mA.

6. Select Power Source

Depending on the power source, make sure you

connect jumpers to the appropriate pins on the

“Power Source” header. For instance, if you use

batteries, use a jumper to short-circuit pin 1 and

2 on the header. See back side of board for

explanation of the jumpers..

Note that there should only be one active

power source at any one time. Do not leave

the EVM powered when unattended.

7. Welcome Screen

Turn on power with the Main Power switch. You

should now see the Texas Instruments logo and

a short description of the buttons on the LCD.

Pushing any of the five buttons on the board will

take you to the main menu.

NB! If you don’t see anything on the screen

make sure the mode switches are in the

correct positions (see step 4 above).

8. Packet Error Rate Test

Select the PER (Packet Error Rate) test by

highlighting the selection using the up/down

buttons. Confirm your selection by pressing

Enter (right button).

9. Select Test Mode

The PER test can be run is several modes. Easy

Mode sets up a one-way test and uses default

settings. This test is convenient for practical

range testing.

The other test modes are described in the

“Software Examples for CC112x, CC11xL and

CC1101 User’s Guide”.

To proceed, highlight “Easy Mode” and press

Enter (right button).

Connectors

MSP430

Breakout

USB

Breakout

Main

Power

Switch

Power

Selection

Board Mode

Switches

LCD

Buttons

LEDs

MSP430

Debug

Interface

connector

10. Select Frequency

Select which frequency to use for the test. Make

sure that the evaluation modules you have

match the selected frequency.

11. Select Mode

One of the boards must operate as the slave

(transmitter) and the other as master (receiver).

Select Slave on one board…

…and Master on the other board.

12. Establish Link

The slave node will now wait for a configuration

package from the Master. The configuration

contains the parameters used for the PER test.

The configuration package will be sent when you

select “link devices” on the master node.

13. Link Established

When the initial linking has completed, the slave

node will start the test by continuously

transmitting packets to the master.

14. Start the Receiver (master)

On the master node, you can select the number

of packets you want to receive in order to

calculate the packet error.

When selecting “Start PER Test”, the master

(receiver) will begin to count the number of

received packets and provide some statistics.

15. PER Test Results

The master will display a window that plots the

received signal strength (RSSI) for each packet.

Press the “Up” button to go to the detailed

statistical window.

16. PER Test Results

The statistics window will show the error rate

based on the number of lost or erroneous

packets divided by the total number of packets

that should have been received.

17. Troubleshooting

It you are experiencing problems with this test,

please check the following:

Nothing is shown in the display! Make sure

the mode switches are in the correct

positions (see step 4 above).

Please visit the kit web page and check for

updated SW and documentation. Updated

SW can be downloaded to the device using

IAR EW430 or SmartRF Flash Programmer.

If you get poor PER results at short

distances, try to move the transmitter and

receiver further apart. The CC1125 receiver

may be saturated if it is too close to the other

CC1125 transmitting at full output power.

18. References

Please visit www.ti.com and

http://www.ti.com/tool/cc1125dk

On the kit product page, you will find additional

documentation, links to updated software

examples and software tools like SmartRF

Studio.

You will also find a lot of information on the TI

E2E forum at http://e2e.ti.com

We hope that you will enjoy working with the

CC1125 device.

SmartRF™Studio

1. Download and Install

Before connecting SmartRF TrxEB to your PC,

download and install SmartRF Studio from

www.ti.com/smartrfstudio.

2. Launch SmartRF Studio

After installing the tool, connect the EB to the PC

using the USB cable and start SmartRF Studio.

Select the “Sub 1 GHz” tab and double click the

highlighted CC1125 device icon.

3. Test the Radio

You can now configure the radio, run

performance tests, export register settings and

run link tests with another CC1125 on a

SmartRF TrxEB connected to the PC.

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following

conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user

indemnifies TI from all claims arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/ kit may

be returned within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED

WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF

THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide

prior to handling the product. This notice contains important safety information about temperatures and

voltages. For additional information on TI's environmental and/or safety programs, please visit

www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to

any machine, process, or combination in which such TI products or services might be or are used. TI

currently deals with a variety of customers for products, and therefore our arrangement with the user is not

exclusive. TI assumes no liability for applications assistance, customer product design, software

performance, or infringement of patents or services described herein.

Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may

not be subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for

ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not

considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can

radiate radio frequency energy and has not been tested for compliance with the limits of computing devices

pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against

radio frequency interference. Operation of the equipment may cause interference with radio communications,

in which case the user at his own expense will be required to take whatever measures may be required to

correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in

legally allocated frequency and power limits. Any use of radio frequencies and/or power availability of this

EVM and its development application(s) must comply with local laws governing radio spectrum allocation and

power limits for this evaluation module. It is the user’s sole responsibility to only operate this radio in legally

acceptable frequency space and within legally mandated power limitations. Any exceptions to this is strictly

prohibited and unauthorized by Texas Instruments unless user has obtained appropriate

experimental/development licenses from local regulatory authorities, which is responsibility of user including

its acceptable authorization.

SSZZ027 December 2011

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

SSZZ027 December 2011

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the

user guide with the maximum permissible gain and required antenna impedance for each antenna type

indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for

that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la

conformité ont pu vider l’autorité de l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans

le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le

type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne

énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque

type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain

maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SSZZ027 December 2011

【Important Notice for Users of this Product in Japan】

This development kit is NOT certified as Confirming to Technical Regulations of

Radio Law of Japan!

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with

respect to this product:

(1) Use this product in a shielded room or any other test facility as defined in the notification #173

issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of

Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan,

(2) Use this product only after you obtained the license of Test Radio Station as provided in Radio

Law of Japan with respect to this product, or

(3) Use of this product only after you obtained the Technical Regulations Conformity Certification as

provided in Radio Law of Japan with respect to this product.

Also, please do not transfer this product, unless you give the same notice above to the transferee.

Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law

of Japan. Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjukku-ku, Tokyo, Japan

http://www.tij.co.jp

【ご使用にあたっての注意】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますの

でご注意ください。

（１）電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた

電波暗室等の試験設備でご使用いただく。

（２）実験局の免許を取得後ご使用いただく。

（３）技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転でき

ないものとします。

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SSZZ027 December 2011

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated,

this EVM is not a finished electrical equipment and not intended for consumer use. It is intended solely for

use for preliminary feasibility evaluation in laboratory/development environments by technically qualified

electronics experts who are familiar with the dangers and application risks associated with handling electrical

mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but

not limited to Food and Drug Administration regulations, if applicable) which relate to your products and

which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM

for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all

such laws and other applicable regulatory requirements, and also to assure the safety of any activities to

be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM.

Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the

EVM and any human body are designed with suitable isolation and means to safely limit accessible

leakage currents to minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property

damage, injury or death, even if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing

materials

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and

environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not

limited to input and output voltage, current, power, and environmental ranges) may cause property damage,

personal injury or death. If there are questions concerning these ratings please contact a TI field

representative prior to connecting interface electronics including input power and intended loads. Any loads

applied outside of the specified output range may result in unintended and/or inaccurate operation and/or

possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide

prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please

contact a TI field representative. During normal operation, some circuit components may have case

temperatures greater than 60 C as long as the input and output are maintained at a normal ambient

operating temperature. These components include but are not limited to linear regulators, switching

transistors, pass transistors, and current sense resistors which can be identified using the EVM schematic

located in the EVM User's Guide. When placing measurement probes near these devices during normal

operation, please be aware that these devices may be very warm to the touch. As with all electronic

evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics

normally found in development environments should use these EVMs

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its

licensors and their representatives harmless from and against any and all claims, damages, losses,

expenses, costs and liabilities (collectively, "Claims") arising out of or in connection with any use of the EVM

that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims arise

under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or

expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in

safety critical applications (such as life support) where a failure of the TI product would reasonably be

expected to cause severe personal injury or death, such as devices which are classified as FDA Class III or

similar classification, then you must specifically notify TI of such intent and enter into a separate Assurance

and Indemnity Agreement.

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Table des matières

Autres manuels Texas Instruments Microcontrôleur

Texas Instruments

Texas Instruments MSP430F6735 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

Texas Instruments

Texas Instruments CC2540 Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad LP-CC1352P7-1 Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0G310 Series Manuel utilisateur

Texas Instruments

Texas Instruments Hercules TMS570LS31x Manuel utilisateur

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuel utilisateur

Texas Instruments

Texas Instruments CC2531 Manuel utilisateur

Texas Instruments

Texas Instruments AM437x Manuel utilisateur

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuel utilisateur

Texas Instruments

Texas Instruments CC3220 Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430F5529LP Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon Products CC2420 Manuel utilisateur

Texas Instruments

Texas Instruments OPT3002EVM Manuel utilisateur

Texas Instruments

Texas Instruments mmWaveICBoost Manuel utilisateur

Texas Instruments

Texas Instruments MSP430FG6425 Manuel utilisateur

Texas Instruments

Texas Instruments TI-InnovatorHub Manuel utilisateur

Texas Instruments

Texas Instruments MSP430G2533 Manuel utilisateur

Texas Instruments

Texas Instruments TMS570LS Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad C2000 F280015 Series Manuel utilisateur

Texas Instruments

Texas Instruments MSP430FG461x series Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink Ethernet MSP432E401Y Manuel utilisateur

Texas Instruments

Texas Instruments Errata MSP430F6746 Manuel utilisateur

Texas Instruments

Texas Instruments LaunchPad MSP430FR5994 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuel utilisateur

Mikroe

Mikroe click Proximity 2 Manuel utilisateur