StarTech.com 5port Manuel utilisateur

Installation Manual

5PORT

Ethernet Hub

5 Port 10BaseT Micro Hub

Overview

The StarTech.com 5 Port 10BaseT micro hub may be small in size, but it is not small on

value. With 5 UTP/STP ports, and the ability to be daisy chained with up to 4 other

hubs, the 5PORT delivers lots of expandability for the future.

Features

• Fully conforms to IEEE 802.3 10BaseT repeater specifications

• Automatic bad port partitioning isolates problem-causing workstations

• Allows data recovery without signal distortion

• LED indicators provide Link/Activity, Collision, Power status

• Uplink port allows for cascade expansion

• Ultra-compact size minimizes equipment space requirements

• Includes AC power adapter (120V) and wall-mounting screws

• 2-year Warranty

Specifications

Getting Started

This section is designed to help you prepare the 5PORT for installation. Please read

through this section carefully before attempting to install the card.

Unpacking the 5PORT

This package should contain:

1 x 5 Port 10BaseT Micro Hub

1 x External power adapter

Standards

Data Transfer Rate

10Mbps Ports

Uplink Port

LEDs

Power

Dimensions

Weight

Operating Humidity

Certification

IEEE 802.3/10BaseT

10Mbps

(5) RJ-45

(1) RJ-45

(5) Link/Activity, Collision, Power

12V DC 0.5A external power adapter

127 x 83 x 30 mm (5.0 x 3.27 x 1.18 inches)

180g (0.4lb)

10~95% (Noncondensing)

FCC Class B, CE Mark

Installation

Physical Description

Operating Environment

This hub must be installed and operated within the limits of the specified operating

temperature and humidity (see Specifications). Do not place objects on top of the unit.

Do not obstruct any vents at the sides of the unit. Do not position the hub near any

heating source such as a heater radiator or in direct exposure to the sun. Prevent water

and moisture from entering into the unit. If necessary, use a dehumidifier to reduce

humidity.

5 Port Ethernet Hub

5PORT

Collision LED

Power LED Link/Activity LED

Power Connector RJ45 Connector Uplink Port

Panel

LED

Power

COL

LNK/ACT

(Link/Activity)

Lit

Off

Lit

Off

Lit

Flash

Off

Power is supplied

No Power

Collision detected

in this segment

No Collision

A valid link is

established

Data packets received

No link is established

One for the whole Hub

One

One for each port

Status Description Number of LED

LED

Connecting Network Devices

1. Connect a Category 5 patch cable to the RJ45 jack on your computer’s network card.

(The RJ45 jack looks like an oversized phone jack)

2. Connect the other end of the cable to port 1, 2, 3, 4 or 5 on the hub (not the uplink

port)

3. Repeat steps 1 and 2 for all the computers you want to network.

Uplink to Another Hub

Use the Uplink port (the first port) to connect to another hub. Connecting cables must

comply with EIA.TIA 568 specifications and Category 3, 5 standards to connect hubs.

Connecting the Power

Connect the power cord to the power socket on the external power adapter. Connect the

DC power jack to the DC power socket on the rear panel of the hub. Connect the power

cord to the power outlet. The Power LED on the front panel should be lit.

Troubleshooting

1. Power LED is not lit

• Check if the power cord is properly connected to the external power adapter and the

power outlet. Make sure the DC power jack is firmly plugged into the power socket

of the hub.

2. Link Status LED is not lit

• Check the power switch of the network devices attached to the hub; make sure they

are turned ON. Check the network cables; make sure they are properly connected to

the hub and network devices.

• Check the network cables; make sure the cables are comply with EIA/TIA 568

specification. Use straight-through Category 3 or 5 cables for connection.

3. The first port’s Link Status LED is not lit when it is uplinked to another hub

• Make sure the cable is connected to the uplink port.

• Check the network cable; make sure it is properly connected to both hubs. One end

of the cable should be connected to the uplink port while the other end of the cable

should be connected to a regular port. Do not connect the cable to both uplink ports.

• Check the network cable; make sure the cable complies with EIA/TIA

568 specifications.

4. Collision LED flashes constantly

• Remove all the network cables; connect the cables back on by one to isolate the

source of collision.

• Check the network cable. Inferior cable quality will result in excessive collision and

error packets.

Table des matières

Autres manuels StarTech.com Changer

StarTech.com

StarTech.com ICUSB23216FD Manuel utilisateur

StarTech.com

StarTech.com HB30C4AIB Manuel utilisateur

StarTech.com

StarTech.com VS410RVGAA Manuel utilisateur

StarTech.com

StarTech.com SV211DPUA4K Manuel utilisateur

StarTech.com

StarTech.com VS420RDVIA Manuel utilisateur

StarTech.com

StarTech.com HB20A7AME Manuel utilisateur

StarTech.com

StarTech.com ConvergeAV VS410HDMIE Manuel utilisateur

StarTech.com

StarTech.com SV431DPDDUA2 Manuel utilisateur

StarTech.com

StarTech.com 8 Port StarView CAT5 UTP KVM Manuel utilisateur

StarTech.com

StarTech.com SV221NANOU Manuel utilisateur

StarTech.com

StarTech.com SV211 Manuel

StarTech.com

StarTech.com ICUSB2321X Manuel utilisateur

StarTech.com

StarTech.com VS221HD4KA Manuel utilisateur

StarTech.com

StarTech.com SV431DUSBU Manuel utilisateur

StarTech.com

StarTech.com IES5102 Manuel utilisateur

StarTech.com

StarTech.com MSTCDP123HD Manuel utilisateur

StarTech.com

StarTech.com VS721MULTI Manuel utilisateur

StarTech.com

StarTech.com HB30C3A1GEA Manuel utilisateur

StarTech.com

StarTech.com SV231DVIUDDM Manuel utilisateur

StarTech.com

StarTech.com VS221HDQ Manuel utilisateur

StarTech.com

StarTech.com SV231DPU34K Manuel utilisateur

StarTech.com

StarTech.com ConvergeAV VS410HDMIE Manuel utilisateur

StarTech.com

StarTech.com DS52000 Manuel utilisateur

StarTech.com

StarTech.com ICUSB2324I Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur