StarTech.com SV211 Manuel

Keyboard/video/mouse

sharing switch

SV211

SV211K

SV411

SV411K Instruction Guide

The Professionals’ Source For Hard-to-Find Computer Parts

KVM SWITCH

* Actual product may vary from photo

* SV411 shown

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Using Your KVM Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Introduction

Thank you for purchasing a StarTech.com economy KVM switch. Now you can control

multiple IBM-compatible computers using just one keyboard, monitor, and mouse. Ideal

for SOHO environments, this StarView switch lets you switch between computers using

either the convenient push-button or a simple hot-key combination. These switches also

support hot-plugging, allowing you to add or remove PCs without resetting the switch.

With the SV211K and SV411K, StarTech.com’s 3-in-1 KVM cables are provided. The

SV211 and SV411 allow you to purchase a 3-in-1 cable in the length of your choice.

Features

• Allows you to control two (SV211, SV211K) or four (SV411, SV411K) PCs from one

PS/2 mouse, PS/2 keyboard, and VGA monitor

• Provides keyboard and mouse emulation to prevent boot-up errors

• Supports hot-plugging

• Capable of up to 1920 x 1440 VGA resolution

• DDC2B compatible

•SV211K/SV411K only: Includes high-quality StarTech.com 3-in-1 cables

• Backed by StarTech.com’s one-year warranty

Before You Begin

To ensure a quick and easy device installation, please read through this section carefully

before attempting to install the switch.

System Requirements

• Two (SV211, SV211K) or four (SV411, SV411K) IBM-compatible computers

• A PS/2 mouse, PS/2 keyboard, and VGA monitor

•SV211, SV411 only: Each computer requires a 3-in-1 KVM cable (not included)

NOTE: StarTech.com carries a wide range of 3-in-1 cables, KVM converters, and other

KVM accessories. Visit www.startech.com for details.

Contents

• 1 x KVM sharing switch

•SV211K/SV411K only: StarTech.com 5.9ft (1.8m) 3-in-1 KVM cables

Installation

This section will guide you through the installation of your KVM switch. Please read

through this section carefully and complete each step in the order listed.

Connecting Your Console

1. Make sure that all devices are turned off and unplugged.

2. Plug your PS/2 keyboard into the purple mini-DIN-6 port on the switch. On the

SV211 and SV211K, the keyboard port is located on the back of the switch. On the

SV411 and SV411K, the keyboard port is located on the right side of the switch.

3. Plug your PS/2 mouse into the green mini-DIN-6 port on the switch. On the SV211

and SV211K, the mouse port is located on the back of the switch. On the SV411 and

SV411K, the mouse port is located on the right side of the switch.

4. Plug your monitor into the HD-DB-15 monitor port located on the right side of the

back of the switch.

NOTE: The KVM switch uses negligible power and is designed to run without an

external power source. You can, however, plug a DC9V power adapter (not included)

into the device’s optional power port.

Connecting Your Computers

The KVM switch requires the use of StarTech.com 3-in-1 KVM cables (included with the

SV211K and SV411K). The “single” end of the cable connects to the KVM switch, the

“triple” end connects to your computer.

1. Make sure all computers are turned off.

2. Plug the single HD-DB-15 connector into one of the PC ports on the back of the

switch.

3. Plug the blue HD-DB-15 connector into your PC’s monitor port.

4. Plug the purple keyboard connector into your PC’s keyboard port.

5. Plug the green mouse connector into your PC’s mouse port.

6. Repeat steps 2 to 5 for each computer you want to connect to the switch.

7. Turn on all computers.

NOTE: You can hot-plug additional computers to the KVM switch any time after the

initial power up.

Using Your KVM Switch

The LEDs on the switch indicate which PC is active. You can scroll between PCs by either

pressing the push-button on the top of the switch or by using a hotkey command. A

hotkey command is a short sequence of keystrokes beginning with two left Ctrl

keystrokes followed by another keystroke. Use only the left Ctrl key and do not use the

keypad at the right of the keyboard.

Selecting a Computer

Auto-Scan Mode

Auto-scan mode will be suspended if the switch detects any keyboard or mouse activity.

When the activity ceases, auto-scan mode will resume. The auto-scan interval can be set

to 3seconds (default setting, represented by one beep), 8seconds (two beeps), 15 seconds

(three beeps), and 30 seconds (four beeps).

Keyboard Typematic Rate

The keyboard typematic rate set on the KVM will over-ride any typematic rate set by the

PC’s BIOS or operating system. The typematic rate can be set to 10 characters/second

(represented by one beep), 15 characters/second (two beeps), 20 characters/second

(three beeps), or 30 characters/second (four beeps).

Command Hotkey sequence

Select computer 1 Left Ctrl + Left Ctrl + 1

Select computer 2 Left Ctrl + Left Ctrl + 2

Select computer 3 Left Ctrl + Left Ctrl + 3 (SV411, SV411K only)

Select computer 4 Left Ctrl + Left Ctrl + 4 (SV411, SV411K only)

Scroll between powered-on Left Ctrl + Left Ctrl + F2 + Up/Down arrow

computers

Command Hotkey sequence

Start auto-scan Left Ctrl + Left Ctrl + F1

End auto-scan Left Ctrl + Left Ctrl

Select auto-scan interval Left Ctrl + Left Ctrl + F3

Command Hotkey sequence

Adjust typematic rate Left Ctrl + Left Ctrl + F4

Troubleshooting

If you are experiencing any difficulties, first make sure that all your cables are connected

to their proper ports and are firmly seated.

My keyboard or mouse does not work.

The keyboard or mouse may not have initialized properly. Press and hold the push

button for three seconds to re-initialize the keyboard and mouse. If problems persist,

unplug the mouse or keyboard, wait a few seconds, then plug them back in.

My keyboard strokes are shifted.

The computer was left in a shifted state when last switched. Press both Shift keys.

The Up and Down arrow keys do not work in manual scan mode.

You may only have one computer turned on. Manual scan will only scroll through

powered-on computers.

My KVM switch occasionally fails to function.

Your computers might not be providing enough power for the switch to function

correctly. Plug a DC9V 500mA (minimum) power adapter into the power port on the

switch.

My auto-scan interval keeps returning to the default.

If all computers connected to the KVM switch are turned off, the KVM will return to its

default settings. If you want to keep your auto-scan interval, make sure that at least one

of your computers is on at all times.

The LED on my SV411/SV411K keeps flashing.

The LED on the SV411/SV411K will flash while in Auto-Scan or Manual Scan modes.

There is nothing wrong with the switch.

Technical Specifications

Number of computers supported SV211, SV211K: Two

SV411, SV411K: Four

Front panel control button One

Auto-scan interval 3, 8, 15, 30 seconds

Typematic rate 10, 15, 20, 30 characters/second

Cable length (max) 5.9 ft (1.8m)

VGA 1920 x 1440, DDC2B

Computer connector HD-DB-15 female

Console keyboard connector PS/2 female

Console mouse connector PS/2 female

Console monitor connector HD-DB-15 female

Dimensions (L x W x H) SV211, SV211K: 2.76 x 6.30 x 0.83in. (70x160x21mm)

SV411, SV411K: 3.39 x 7.28 x 0.87in. (86x185x22mm)

Certifications FCC, CE, VCCI

Technical Support

The following technical resources are available for this StarTech.com product:

On-line help:

We are constantly adding new information to the Tech Support section of our web site. To

access this page, click the Tech Support link on our homepage, www.startech.com. In the

tech support section there are a number of options that can provide assistance with this

card.

Knowledge Base - This tool allows you to search for answers to common issues using

key words that describe the product and your issue.

FAQ - This tool provides quick answers to the top questions asked by our customers.

Downloads - This selection takes you to our driver download page where you can

find the latest drivers for this product.

Call StarTech.com tech support for help: 1-519-455-4931

Support hours: Monday to Friday 9:00AM to 5:00PM EST (except holidays)

Warranty Information

This product is backed by a one-year warranty. In addition StarTech.com warrants its

products against defects in materials and workmanship for the periods noted below,

following the initial date of purchase. During this period, the products may be

returned for repair, or replacement with equivalent products at our discretion. The

warranty covers parts and labor costs only. StarTech.com does not warrant its products

from defects or damages arising from misuse, abuse, alteration, or normal wear and

tear.

Limitation of Liability

In no event shall the liability to StarTech.com Ltd. (or its officers, directors, employees or

agents) for any damages (whether direct or indirect, special, punitive incidental,

consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss,

arising out of related to the use of the product exceed the actual price paid for

the product.

Some states do not allow the exclusion or limitation of incidental or consequential

damages. If such laws apply, the limitations or exclusions contained in this statement

may not apply to you.

Revised: February 19, 2003

Autres manuels pour SV211

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels StarTech.com Changer

StarTech.com

StarTech.com P4A20132-KM-SWITCH Manuel utilisateur

StarTech.com

StarTech.com SV231DDVDUA Manuel utilisateur

StarTech.com

StarTech.com IES51000POE Manuel utilisateur

StarTech.com

StarTech.com 8ST35BAYUSB3S4 Manuel utilisateur

StarTech.com

StarTech.com SV831DUSBGB Manuel utilisateur

StarTech.com

StarTech.com StarView SV231USBGB Manuel utilisateur

StarTech.com

StarTech.com HB30C3APDW Manuel utilisateur

StarTech.com

StarTech.com USB2HDCAPS Manuel utilisateur

StarTech.com

StarTech.com ST7300USBME Manuel utilisateur

StarTech.com

StarTech.com SV431DLU3A Manuel utilisateur

StarTech.com

StarTech.com VS221HD4K Manuel utilisateur

StarTech.com

StarTech.com MSTCDP123DP Manuel utilisateur

StarTech.com

StarTech.com 8STST7300USBME Manuel utilisateur

StarTech.com

StarTech.com HDVGADP2HD Manuel utilisateur

StarTech.com

StarTech.com IES101002SFP Manuel utilisateur

StarTech.com

StarTech.com SV221MICROUA Manuel utilisateur

StarTech.com

StarTech.com SV831DUSBA Manuel utilisateur

StarTech.com

StarTech.com IES101002SFP Manuel utilisateur

StarTech.com

StarTech.com ST7200USB Manuel utilisateur

StarTech.com

StarTech.com SV231MDPU2 Manuel utilisateur

StarTech.com

StarTech.com SV431USBAE Manuel utilisateur

StarTech.com

StarTech.com SDOCK2U33HFW Manuel utilisateur

StarTech.com

StarTech.com ST7202USBGB Manuel utilisateur

StarTech.com

StarTech.com CPNT410IR Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur