StarTech.com 8 Port StarView CAT5 UTP KVM Manuel utilisateur

StarView CAT5 UTP KVM

8 Port StarView CAT5 UTP KVM

16 Port StarView CAT5 UTP KVM

Instruction Manual

*8 Port Model Shown

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver•

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected

names and/or symbols of third-party companies not related in any way to StarTech.com.

Where they occur these references are for illustrative purposes only and do not represent an

endorsement of a product or service by StarTech.com, or an endorsement of the product(s)

to which this manual applies by the third-party company in question. Regardless of any direct

acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowl-

edges that all trademarks, registered trademarks, service marks, and other protected names

and/or symbols contained in this manual and related documents are the property of their

respective holders.

Instruction Manual

Table of Contents

Safety Precautions ....................................................................... iii

Introduction.................................................................................... 1

Features ......................................................................................1

Package contents ........................................................................1

Hardware Guide ............................................................................. 2

Installation...................................................................................... 6

Stacking Switches and Rack Mounting .......................................6

Single Station Installation ............................................................8

Server Interface Module Installation............................................10

SV5PS2S (PS2 Module)..............................................................10

SV5USBS (USB Module) ............................................................10

Daisy Chaining ............................................................................11

Daisy Chain Installation Diagram ................................................12

Basic Operation............................................................................. 13

Port Selection ..............................................................................13

Hot Plugging................................................................................13

Powering Off and Restarting .......................................................14

Port ID Numbering.......................................................................15

OSD Operation............................................................................... 15

Overview......................................................................................15

OSD Navigation...........................................................................17

OSD Main Screen Headings .......................................................17

OSD Functions ............................................................................17

Hotkey Operation........................................................................... 27

Instruction Manual

Hotkey Port Control .....................................................................27

Auto Scanning .............................................................................28

Skip Mode....................................................................................29

Hotkey Beeper Control.................................................................. 30

Hotkey Summary Table................................................................30

Keyboard Emulation...................................................................... 32

Mac Keyboard..............................................................................32

Sun Keyboard..............................................................................33

Firmware Upgrades....................................................................... 34

Introduction..................................................................................34

Performing the Upgrade ..............................................................35

Server Interface Module Upgrade ................................................ 37

Performing the Upgrade ..............................................................38

Firmware Upgrade Recovery.......................................................39

Connection Tables ......................................................................... 40

Administrator Login Failure ......................................................... 42

OSD Factory Default Settings ...................................................... 43

Speciﬁcations ................................................................................ 44

Technical Support........................................................................46

Warranty Information ...................................................................46

Instruction Manual

iii

Safety Precautions

The following precautions should be employed to ensure safe, reliable

operation of this device:

Read the enclosed instructions, and save them for future reference

Do not place the device on an unstable surface. If the device falls,•

serious damage will result

Follow all warnings and instructions marked on the device (if•

applicable)

Do not use the device near water•

Do not place the device near or over any device that produces heat (i.e.•

radiators, heat registers etc.)

To ensure adequate ventilation and reliable operation, never block the•

vent openings

Do not place the device on a soft surface (i.e. bed, carpet, etc.) as this•

will block ventilation openings. Similarly, never place the device in a

built-in enclosure unless adequate ventilation is provided

Never spill liquid of any kind on the device•

Unplug the device from the wall, prior to cleaning. Do not use liquid or•

aerosol cleaners, instead use a damp cloth

The device should be operated from the type of power source indicated•

on the marking label. If you are unsure of the type of power available,

please contact your local power company

The device is equipped with a 3-wire grounding type plug. This is a•

safety feature that should be left intact at all times. If you are unable to

insert the plug into the outlet, contact your electrician to replace the

available (outdated) outlet. Do not attempt to defeat the purpose of or

bypass the grounding-type plug; always follow local wiring codes

Position system cables and power cables carefully. Do not allow•

anything to rest on the power cord or cables. Route the power cord

and cables so that they cannot be stepped or tripped on

If an extension cord is used with this device, make sure that the•

Instruction Manual

combined ampere rating of all products used on the cord does not

exceed the extension cord ampere rating. Make sure that the total of

all devices connected to the wall outlet does not exceed 15 amperes

To help protect your system from sudden, transient increases and•

decreases in electrical power, use a surge suppressor, line conditioner

or Uninterruptible Power Supply (UPS)

Follow all warnings and instructions marked on the device (if•

applicable)

When connecting or disconnecting power to hot pluggable power•

supplies, observe the following guidelines:

Install the power supply before connecting the power cable to the

power supply

Unplug the power cable before removing the power supply

If the system has multiple sources of power, disconnect power by

unplugging all power cables from the power supplies

Never push objects of any kind into or through cabinet slots. They

may touch dangerous voltage points or short out components,

risking ﬁre or electrical shock.

Do not attempt to service the device yourself. Please refer all servicing•

to qualiﬁed service personnel

Unplug the device from the wall outlet, and consult with a qualiﬁed•

service technician, if any of the following conditions occur:

The power cord is frayed or damaged

Liquid has been spilled into the device, or the device has been

exposed to rain or water

The device has been dropped, or the casing has been damaged

The device exhibits a distinct decline in performance, indicating a

Instruction Manual

need for service

The device does not operate normally, when following the operating

instructions

Only adjust controls that are described in the following operating•

instructions. Improper adjustment of other controls may result in

damage that could lead to extensive repair

Instruction Manual

Introduction

Thank you for purchasing a StarTech.com CAT 5 KVM switch. Allowing

control of up to 8 (SV831DUTP) or 16 (SV1631DUTP) computers over a

CAT 5 cable connection (between the switch and the slave computers),

this device provides a cost-effective solution that’s simple to install, and

equally easy to conﬁgure and control through pushbutton operation, hot-

key commands or the convenient On-Screen Display.

Features

Auto-scan function automates sequential computer selection•

Cascade conﬁguration expands system capability up to 256 computers•

(SV831DUTP) or 512 computers (SV1631DUTP)

Allows for easy computer selection using front panel pushbuttons,•

hotkeys and intuitive On-Screen Display

Hot Pluggable - add or remove computers without having to power•

down the switch

Package contents

1 x StarView CAT5 KVM Switch

1 x User Manual

1 x Power Adapter

1 x Mounting Bracket Kit

1 x Firmware Upgrade Cable

Please note that when accessing the Switch, you will be asked to supply

a Username and Password.

In the Username ﬁeld, press the Enter key on the connected keyboard.

In the Password ﬁeld, press the Enter key. You will then be logged into

the On Screen Display.

Instruction Manual

Hardware Guide

Front Panel View SV831DUTP

Front Panel View SV1631DUTP

1&2 734 5 6

1&2

3764 5

Please refer to the tables on pages 3 and 4 for descriptions

of the above illustrations.

Instruction Manual

Component Functions (Front Panel)

Component Description

Port

Selection

Switches

a. Press a switch to give the KVM focus to the

computer attached to its corresponding port.

b. Simultaneously pressing buttons 1 and 2 for 3

seconds performs a Keyboard and Mouse Reset.

c. Simultaneously pressing buttons 7 and 8 starts Auto

Scan Mode.

2 Port LEDs

The Port LEDs are built into the Port Selection Switches.

The upper ones are the On Line LEDs; the lower ones

are the Selected Port LEDs:

a. An On Line LED lights GREEN to indicate that the

computer attached to its corresponding port is up and

running. A ﬂashing LED indicates that the Port is being

used for cascading to another switch.

b. A Selected LED lights ORANGE to indicate that the

computer attached to its corresponding port is the one

that has the KVM focus.

The LED is steady under normal conditions, but ﬂashes

when its port is accessed under Auto Scan Mode.

3Reset

Switch

Pressing this switch in performs a system reset. Note:

The switch is recessed and must be pushed with a thin

object - such as the end of a paper clip, or a ballpoint

pen.

Firmware

Upgrade

Recovery

Switch

During normal operation and while performing a ﬁrmware

upgrade, this switch should be in the NORMAL position.

If a ﬁrmware upgrade operation does not complete

successfully, this switch is used to perform a ﬁrmware

upgrade recovery.

Table des matières

Autres manuels StarTech.com Changer

StarTech.com

StarTech.com 4PORT-8K-HDMI-SWITCH Manuel utilisateur

StarTech.com

StarTech.com MSTDP122DP Manuel utilisateur

StarTech.com

StarTech.com 8STMSTMDP123HD Manuel utilisateur

StarTech.com

StarTech.com C2-DD46-UA2-CBL-KVM Manuel utilisateur

StarTech.com

StarTech.com STARVIEW SV831SUN Manuel utilisateur

StarTech.com

StarTech.com SV431HU34K6 Manuel utilisateur

StarTech.com

StarTech.com ICUSB23216FD Manuel utilisateur

StarTech.com

StarTech.com SV1115IPEXT Manuel utilisateur

StarTech.com

StarTech.com ST4100USBBL Manuel utilisateur

StarTech.com

StarTech.com SV231QDVIUA Manuel utilisateur

StarTech.com

StarTech.com CAB831HDU Manuel utilisateur

StarTech.com

StarTech.com IES81000POE Manuel utilisateur

StarTech.com

StarTech.com ICUSB2322X Manuel utilisateur

StarTech.com

StarTech.com SV431DL2DU3A Manuel utilisateur

StarTech.com

StarTech.com SV441HDIE Manuel utilisateur

StarTech.com

StarTech.com D86A2-2-PORT-8K-KVM Manuel utilisateur

StarTech.com

StarTech.com MSTMDP123DP Manuel utilisateur

StarTech.com

StarTech.com ST3504USB Manuel utilisateur

StarTech.com

StarTech.com HB30AM4AB Manuel utilisateur

StarTech.com

StarTech.com SV231DVIUAHR Manuel utilisateur

StarTech.com

StarTech.com 5G4AIBS-USB-HUB-EU Manuel utilisateur

StarTech.com

StarTech.com StarView SV211KA Manuel

StarTech.com

StarTech.com SV441DUSBI Manuel utilisateur

StarTech.com

StarTech.com 8STMSTMDP124DP Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur