SMART SBID 8084i-G4 Manuel utilisateur

1 smarttech.com/kb/170597 1022737 Rev 01

Important

Before you configure your

SMARTBoard® 8084i-G4

interactive flat panel

You need to set the computer (or Microsoft®Lync® appliance) input’s operating mode to “PC” after

you turn on your SMARTBoard® 8084i-G4 interactive flat panel for the first time but before you

configure and use the interactive flat panel.

I M P O R T A N T

If you do not complete this procedure, the following could occur:

lThe interactive flat panel might not display the outer edges of the computer’s display.

lUsers might notice higher than normal video display latency.

To set the computer input’s operating mode to “PC”

1. Turn on the interactive flat panel.

2. If you’re installing the interactive flat panel as part of a SMARTRoomSystem™ for

MicrosoftLync, set the Lync Room Reset option as described in chapter 3 of the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

3. On the remote control, press INPUT (a), and then press the red button (b),

which is below the BACK button.

The Input Label menu appears.

I M P O R T A N T

Before you configure your SMARTBoard 8084i-G4 interactive flat panel

2 smarttech.com/kb/170597 1022737 Rev 01

4. Using the left and right arrow buttons on the remote control, select the input that the computer is

connected to, and then press OK.

N O T E

If you’re installing the interactive flat panel as part of a SMARTRoomSystem, select

HDMI3/PC.

5. Using the left, right, up and down arrow buttons on the remote control, select PC, and then

pressOK.

6. Press the down arrow on the remote control to select Close, and then press OK.

In the Input List menu, the computer input’s icon indicates that its operating mode is “PC.”

7. Calibrate and orient the interactive flat panel as documented in the SMARTBoard 8000i-G4

interactive flat panel setup and maintenance guide (smarttech.com/kb/170446) or the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

N O T E

In most situations, the only time you need to make this change is during the initial

configuration of the interactive flat panel. However, if you subsequently complete a

FactoryReset or LyncRoomReset, you need to complete this procedure afterward.

smarttech.com/support

smarttech.com/contactsupport

© 2013SMARTTechnologiesULC. All rights reserved. SMARTBoard, SMARTRoomSystem, smarttech, the SMART logo and all SMART taglines are trademarks or

registered trademarks of SMARTTechnologiesULC in the U.S. and/or other countries. Microsoft and Lync are either registered trademarks or trademarks of Microsoft

Corporation in the U.S. and/or other countries. All other third-party product and company names may be trademarks of their respective owners. Contents are subject to

change without notice. 10/2013.

Table des matières

Autres manuels SMART Tableau blanc interactif

SMART

SMART 2000i-DVS Manuel utilisateur

SMART

SMART Table 230i Manuel utilisateur

SMART

SMART SMART Board Manuel utilisateur

SMART

SMART KAPP42 Manuel utilisateur

SMART

SMART Board 6000 Series Manuel utilisateur

SMART

SMART M600i6 Manuel utilisateur

SMART

SMART Board 600i3 Manuel utilisateur

SMART

SMART 8070i Manuel utilisateur

SMART

SMART Podium 500 Series Manuel utilisateur

SMART

SMART 8084i-G4-SMP Manuel utilisateur

SMART

SMART Board 685ix Manuel utilisateur

SMART

SMART 8070i-SMP Manuel utilisateur

SMART

SMART SBX885 Manuel utilisateur

SMART

SMART kapp 84 Manuel utilisateur

SMART

SMART 8070i-SMP Manuel utilisateur

SMART

SMART Smart Board 480 Manuel utilisateur

SMART

SMART Inforce 67X1 Manuel utilisateur

SMART

SMART SmartBoard 600i2 Manuel utilisateur

SMART

SMART UF45-680 Manuel utilisateur

SMART

SMART Podium ID422w Manuel utilisateur

SMART

SMART SBID8055i-G5-SMP Manuel de service

SMART

SMART SBX880 Manuel utilisateur

SMART

SMART SB880i5-MP Manuel utilisateur

SMART

SMART Board 6065 Manuel d'utilisation

Manuels Tableau blanc interactif populaires d'autres marques

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Manuel utilisateur

Buhl

Buhl LyteBoard Manuel utilisateur

SMART Board

SMART Board 680 Manuel utilisateur

Legamaster

Legamaster e-SCREEN ETX Manuel utilisateur

SMART Board

SMART Board SBM685ix2 Manuel utilisateur

Seneca

Seneca eno Manuel utilisateur

BenQ

BenQ RP840G Manuel utilisateur

Olivetti

Olivetti OLIBOARD Manuel utilisateur

Turning Technologies

Turning Technologies MOBIVIEW Manuel utilisateur

Panasonic

Panasonic UB-5335 Manuel utilisateur

Dukane

Dukane ITP84 Manuel utilisateur

Bretford

Bretford EDUIMS Guide de configuration

Panasonic

Panasonic Panaboard UB-5315 Manuel utilisateur

Plus

Plus M-11S Manuel utilisateur

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Manuel utilisateur

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Manuel utilisateur

AVer

AVer CP series Manuel utilisateur

Genee

Genee 56" Manuel utilisateur