SIGMA TEK AO 046 Manuel utilisateur

AO 046

S-DIAS Analog Output Module

Instruction Manual

Date of creation: 06.06.2017

Version date: 26.07.2023

Article number: 20-010-046-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

tributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi-

ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through

use of this handbook.

S-DIAS ANALOG OUTPUT MODULE AO 046

26.07.2023 Page 1

S-DIAS Analog Output Module AO 046

with 4 outputs (voltage/current switchable)

The S-DIAS AO 046 analog output module has four ±10.8 V or

0-21.6 mA analog outputs with a resolution of 16 bits. The analog out-

puts are powered by an external +24 V supply. The analog output sys-

tem is galvanically separated from the potential of the S-DIAS bus.

AO 046 S-DIAS ANALOG OUTPUT MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Analog Output Voltage Specifications.....................................13 
5.2 Output Accuracy Analog Outputs Voltage...............................13 
5.3 Analog Output Current Specifications.....................................14 
5.4 Output Accuracy Analog Outputs Current...............................14 
5.5 Settling Time of the Analog Outputs........................................15 
5.6 Electrical Requirements.............................................................16 
5.7 Voltage Monitoring External +24 V Supply..............................18 

 S-DIAS ANALOG OUTPUT MODULE AO 046 
 
07.2023 Page 3 
8 Miscellaneous .............................................................................18 
9 Environmental Conditions.........................................................18 
6Mechanical Dimensions........................................................19 
7Connector Layout..................................................................20 
1 Status LEDs.................................................................................21 
2 Applicable Connectors...............................................................22 
3 Label Field...................................................................................23 
8Wiring.....................................................................................24 
1 Wiring Example...........................................................................24 
2 Note..............................................................................................25 
9Assembly/Installation ...........................................................26 
1 Check Contents of Delivery.......................................................26 
2 Mounting......................................................................................27 
Addressing.............................................................................29 
Transport/Storage.................................................................32 
Storage...................................................................................32 
Maintenance...........................................................................33 
1 Service.........................................................................................33 
2 Repair...........................................................................................33 

AO 046 S-DIAS ANALOG OUTPUT MODULE 
 
Page 4 26.07.2023 
Disposal..................................................................................33 
Hardware Class AO046..........................................................34 
1 General.........................................................................................35 
2 Analog Outputs [1-4] ..................................................................36 
3 Time Offset Mode........................................................................38 
4 Communication Interfaces.........................................................38 
5 Internal Properties......................................................................39 
5.1 Time Offset Mode for Analog Outputs...............................................39 
5.2 Limitations of this Mode.....................................................................39 
 

S-DIAS ANALOG OUTPUT MODULE AO 046

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x AO 046

AO 046 S-DIAS ANALOG OUTPUT MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the speci-

fied measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS ANALOG OUTPUT MODULE AO 046

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require atten-

tion.

AO 046 S-DIAS ANALOG OUTPUT MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the sub-

sequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine opera-

tor is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If neces-

sary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product descrip-

tion. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this operat-

ing manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Table des matières

Autres manuels SIGMA TEK Unité de contrôle

SIGMA TEK

SIGMA TEK C-DIAS Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111-S Manuel utilisateur

SIGMA TEK

SIGMA TEK S-DIAS EC 121 Manuel utilisateur

SIGMA TEK

SIGMA TEK PIM 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK SRO 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK CSDI 162 Manuel utilisateur

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Manuel utilisateur

SIGMA TEK

SIGMA TEK PIM 041-W Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 112 Manuel utilisateur

SIGMA TEK

SIGMA TEK DC 061-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK MDD 111-2 Manuel utilisateur

SIGMA TEK

SIGMA TEK CCP 531 Manuel utilisateur

SIGMA TEK

SIGMA TEK ISE 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 102 Manuel utilisateur

SIGMA TEK

SIGMA TEK VI 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK BL 011 Manuel utilisateur

SIGMA TEK

SIGMA TEK NC 100 Manuel utilisateur

SIGMA TEK

SIGMA TEK KL 090 Manuel utilisateur

SIGMA TEK

SIGMA TEK MDP 102-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK AM 441 Manuel utilisateur

SIGMA TEK

SIGMA TEK TO 161 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111-2 Manuel utilisateur

SIGMA TEK

SIGMA TEK ST 011 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur