SIGMA TEK KL 180 Manuel utilisateur

KL 180

S-DIAS 0 V Potential Distributor

Module

Instruction Manual

Date of creation: 30.07.2013

Version date: 26.07.2023

Article number: 20-024-180-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180

26.07.2023 Page 1

S-DIAS 0 V Potential Distributor Module KL 180

with 18 0 V terminals

The KL 180 S-DIAS 0 V potential distributor module has 18 terminals.

The voltage tap is possible without an additional series terminal.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 4 
1.1 Target Group/Purpose of this Operating Manual......................4 
1.2 Important Reference Documentation .........................................4 
1.3 Contents of Delivery.....................................................................4 
2Basic Safety Directives .......................................................... 5 
2.1 Symbols Used...............................................................................5 
2.2 Disclaimer......................................................................................7 
2.3 General Safety Directives ............................................................8 
2.4 Software/Training .........................................................................9 
3Standards and Directives......................................................10 
3.1 Directives.....................................................................................10 
3.1.1 EU Conformity Declaration................................................................10 
4Type Plate...............................................................................11 
5Technical Data .......................................................................12 
5.1 0 V Supplies.................................................................................12 
5.2 Electrical Requirements.............................................................12 
5.3 Miscellaneous .............................................................................14 
5.4 Environmental Conditions.........................................................14 
6Mechanical Dimensions........................................................15 
7Connector Layout..................................................................16 

 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180 
 
07.2023 Page 3 
1 Applicable Connectors...............................................................17 
2 Label Field...................................................................................18 
8Wiring.....................................................................................19 
1 Wiring Example...........................................................................19 
9Assembly/Installation ...........................................................20 
1 Check Contents of Delivery.......................................................20 
2 Mounting......................................................................................21 
Transport/Storage .................................................................23 
Storage...................................................................................23 
Maintenance...........................................................................24 
1 Service.........................................................................................24 
2 Repair...........................................................................................24 
Disposal .................................................................................24 
 

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE

Page 4 26.07.2023

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x KL 180

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180

26.07.2023 Page 5

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE

Page 6 26.07.2023

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180

26.07.2023 Page 7

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE

Page 8 26.07.2023

2.3 General Safety Directives

The Safety Directives in the other sections of this operating manual must be observed.

These instructions are visually emphasized by symbols.

INFORMATION

According to EU Directives, the operating manual is a component of a

product.

This operating manual must therefore be accessible in the vicinity of

the machine since it contains important instructions.

This operating manual should be included in the sale, rental or transfer

of the product, or its online availability indicated.

Regarding the requirements for Safety and health connected to the use

of machines, the manufacturer must perform a risk assessment in

accordance with machine directives 2006/42/EG before introducing a

machine to the market.

Operate the unit with devices and accessories approved by

SIGMATEK only.

Table des matières

Autres manuels SIGMA TEK Unité de contrôle

SIGMA TEK

SIGMA TEK PIM 041-W Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 102 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111-S Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111 Manuel utilisateur

SIGMA TEK

SIGMA TEK CCP 531 Manuel utilisateur

SIGMA TEK

SIGMA TEK C-DIAS Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 011 Manuel utilisateur

SIGMA TEK

SIGMA TEK DM 167 Manuel utilisateur

SIGMA TEK

SIGMA TEK EZ 101 Manuel utilisateur

SIGMA TEK

SIGMA TEK PW 022 Manuel utilisateur

SIGMA TEK

SIGMA TEK AM 222 Manuel utilisateur

SIGMA TEK

SIGMA TEK DC 061-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK KL 090 Manuel utilisateur

SIGMA TEK

SIGMA TEK TO 161 Manuel utilisateur

SIGMA TEK

SIGMA TEK AI 047 Manuel utilisateur

SIGMA TEK

SIGMA TEK SRO 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111-S Manuel utilisateur

SIGMA TEK

SIGMA TEK SDM 081 Manuel utilisateur

SIGMA TEK

SIGMA TEK MDP 102-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK PIM 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK BL 011 Manuel utilisateur

SIGMA TEK

SIGMA TEK DC 061-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 112-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK PL 221 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur