SIGMA TEK TO 161 Manuel utilisateur

TO 161

S-DIAS Digital Output Module

Operating Manual

Date of creation: 30.07.2013

Version date: 26.07.2023

Article number: 20-007-161-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: office@sigmatek.at

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS DIGITAL OUTPUT MODULE TO 161

26.07.2023 Page 1

S-DIAS Digital Output Module TO 161

with 16 short-circuit proof digital outputs

The S-DIAS TO 161 digital output module has 16 short-circuit proof

digital outputs in two groups (+24 V/0.5 A, short-circuit proof). The

supply voltage for each group is monitored for low voltage.

TO 161 S-DIAS DIGITAL OUTPUT MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Digital Output Specifications.....................................................13 
5.2 Electrical Requirements.............................................................14 
5.3 Voltage Monitor...........................................................................16 
5.4 Miscellaneous .............................................................................16 
5.5 Environmental Conditions.........................................................16 
6Mechanical Dimensions........................................................17 

 S-DIAS DIGITAL OUTPUT MODULE TO 161 
 
07.2023 Page 3 
7Connector Layout..................................................................18 
1 Status LEDs.................................................................................19 
2 Applicable Connectors...............................................................19 
3 Label Field...................................................................................20 
8Wiring.....................................................................................21 
1 General Information on the Digital Outputs.............................21 
2 Wiring Example...........................................................................22 
3 Note..............................................................................................23 
9Assembly/Installation ...........................................................24 
1 Check Contents of Delivery.......................................................24 
2 Mounting......................................................................................25 
Transport/Storage .................................................................27 
Storage...................................................................................27 
Maintenance...........................................................................28 
1 Service.........................................................................................28 
2 Repair...........................................................................................28 
Disposal .................................................................................28 
Addressing.............................................................................29 
Supported Cycle Times ........................................................30 
1 Cycle Times below 1 ms (in µs).................................................30 

TO 161 S-DIAS DIGITAL OUTPUT MODULE

Page 4 26.07.2023

15.2 Cycle Times equal to or higher than 1 ms (in ms)...................30

16 Hardware Class TO161..........................................................31

16.1 Interfaces.....................................................................................32

16.1.1 Clients ...............................................................................................32

16.1.2 Servers..............................................................................................32

16.1.3 Communication Interfaces.................................................................32

16.2 Example.......................................................................................33

S-DIAS DIGITAL OUTPUT MODULE TO 161

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x TO 161

TO 161 S-DIAS DIGITAL OUTPUT MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS DIGITAL OUTPUT MODULE TO 161

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

TO 161 S-DIAS DIGITAL OUTPUT MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Table des matières

Autres manuels SIGMA TEK Unité de contrôle

SIGMA TEK

SIGMA TEK ST 011 Manuel utilisateur

SIGMA TEK

SIGMA TEK S-DIAS EC 121 Manuel utilisateur

SIGMA TEK

SIGMA TEK SDM 081 Manuel utilisateur

SIGMA TEK

SIGMA TEK SRO 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK MDD 111-2 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111-S Manuel utilisateur

SIGMA TEK

SIGMA TEK SRO 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Manuel utilisateur

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 112-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK HZS 7321 Manuel utilisateur

SIGMA TEK

SIGMA TEK KL 090 Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 102 Manuel utilisateur

SIGMA TEK

SIGMA TEK SCP 111 Manuel utilisateur

SIGMA TEK

SIGMA TEK AI 0812 Manuel utilisateur

SIGMA TEK

SIGMA TEK AM 222 Manuel utilisateur

SIGMA TEK

SIGMA TEK PW 022 Manuel utilisateur

SIGMA TEK

SIGMA TEK ISE 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Manuel utilisateur

SIGMA TEK

SIGMA TEK SAI 041 Manuel utilisateur

SIGMA TEK

SIGMA TEK PL 221 Manuel utilisateur

SIGMA TEK

SIGMA TEK AM 441 Manuel utilisateur

SIGMA TEK

SIGMA TEK DC 061-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 112 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur