Rosemount 3051SMV Manuel utilisateur

www.rosemount.com

¢00825-0100-4801J¤

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011 Rosemount 3051SMV

Rosemount 3051S MultiVariable™

Transmitter

Rosemount 3051SF Series Flowmeter

MultiVariable Transmitter

Step 1: Mount the Transmitter

Step 2: Consider Housing Rotation

Step 3: Set Switches

Step 4: Connect Wiring and Power Up

Step 5: Flow Configuration

Step 6: Verify Device Configuration

Step 7: Trim the Transmitter

Product Certifications

Start

End

4803_QIG_RevBA.fm Page 1 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011

Rosemount 3051SMV

Rosemount logotype are registered trademarks of Rosemount Inc.

Rosemount Inc.

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

F (952) 949-7001

Emerson Process Management

GmbH & Co. OHG

Argelsrieder Feld 3

82234 Wessling

Germany

T 49 (8153) 9390, F49 (8153) 939172

Emerson Process Management

Asia Pacific Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947/65 6777 0743

Beijing Rosemount Far East Instrument

Co., Limited

No. 6 North Street, Hepingli, Dong Cheng District

Beijing 100013, China

T (86) (10) 6428 2233

F (86) (10) 6422 8586

IMPORTANT NOTICE

This installation guide provides basic guidelines for the Rosemount 3051S MultiVariable

transmitter (reference manual document number 00809-0100-4803). It also provides the

basic 3051S MultiVariable transmitter configuration guidelines for the 3051SFA (reference

manual document number 00809-0100-4809), 3051SFC (reference manual document

number 00809-0100-4810), and 3051SFP (reference manual document number

00809-0100-4686). It does notprovide instructions for diagnostics, maintenance, service, or

troubleshooting. Refer to the 3051S MultiVariable transmitter reference manual for more

instruction. All documents are available electronically at

www.emersonprocess.com/rosemount.

WARNING

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local,national, and international standards, codes, and practices. Please review

the approvals section of the 3051S MultiVariable transmitter reference manual

(00809-0100-4803) for any restrictions associated with a safe installation.

• Before connecting a Field communicator in an explosive atmosphere, ensure the

instruments in the loop are installed in accordance with intrinsically safe or

non-incendive field wiring practices.

• In an Explosion-proof/Flameproof installation, do not remove the transmitter covers

when power is applied to the unit.

Process leaks may cause harm or result in death.

• Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be present on leads

can cause electrical shock.

4803_QIG_RevBA.fm Page 2 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011 Rosemount 3051SMV

STEP 1: MOUNT THE TRANSMITTER

Liquid Flow Applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the

drain/vent valves are oriented

upward.

Gas Flow Applications

1. Place taps in the top or side of

the line.

2. Mount beside or above the taps.

Steam Flow Applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

4803_QIG_RevBA.fm Page 3 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011

Rosemount 3051SMV

Mounting Brackets

Coplanar™Flange

Traditional Flange

Pipe MountPanel Mount

Pipe Mount

Panel Mount

4803_QIG_RevBA.fm Page 4 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011 Rosemount 3051SMV

Bolting Considerations

If the transmitter installation requires assembly of a process flange,

manifold, or flange adaptors, follow these assembly guidelines to

ensure a tight seal for optimal performance characteristics of the

transmitter. Only use bolts supplied with the transmitter or sold by

Emerson Process Management as spare parts. Figure 1 illustrates

common transmitter assemblies with the bolt length required for

proper transmitter assembly.

Figure 1. Common Transmitter Assemblies

4 x 1.75-in.

(44 mm)

4 x 2.88-in.

(73 mm)

A. Transmitter with

Coplanar Flange

B. Transmitter with

Coplanar Flange and

Optional Flange

Adapters

C. Transmitter with

Traditional Flange and

Optional Flange

Adapters

D. Transmitter with

Coplanar Flange

and Optional

Manifold and Flange

Adapters

4 x 1.75-in.

(44 mm) 4 x 1.50-in.

(38 mm)

4 x 1.75-in.

(44 mm)

4 x 2.25-in.

(57 mm)

4803_QIG_RevBA.fm Page 5 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011

Rosemount 3051SMV

Bolts are typically carbon steel or stainless steel. Confirm the material

by viewing the markings on the head of the bolt and referencing

Figure 3. If bolt material is not shown in Figure 3, contact the local

Emerson Process Management representative for more information.

Use the following bolt installation procedure:

1. Carbon steel bolts do not require lubrication and the stainless steel

bolts are coated with a lubricant to ease installation. However, no

additional lubricant should be applied when installing either type of

bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern.

See Figure 3 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing

pattern. See Figure 3 for final torque value.

5. Verify that the flange bolts are protruding through the module

isolator plate before applying pressure.

Figure 2. Module Isolator Plate

Figure 3. Torque Values for the Flange and Flange Adapter Bolts

Bolt Material Head Markings Initial Torque Final Torque

Carbon Steel

(CS) 300 in.-lbs. 650 in.-lbs.

Stainless Steel

(SST) 150 in.-lbs. 300 in.-lbs.

Module Isolator Plate

Bolt

B7M

316

STM

316

B8M

4803_QIG_RevBA.fm Page 6 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011 Rosemount 3051SMV

O-rings with Flange Adaptors

WARNING

Whenever the flange or adapters are removed, visually inspect the

o-rings. Replace them if there are any signs of damage, such as nicks

or cuts. If the o-rings are replaced, re-torque the flange bolts and

alignment screws after installation to compensate for seating of the

o-rings.

Failure to install proper flange adapter O-rings may cause process leaks, which

can result in death or serious injury. The two flange adapters are distinguished

by unique O-ring grooves. Only use the O-ring that is designed for its specific

flange adapter, as shown below.

Rosemount 3051S / 3051 / 2051 / 3095

Rosemount 1151

Flange Adapter

O-ring

Flange Adapter

O-ring

PTFE Based

Elastomer

PTFE

Elastomer

4803_QIG_RevBA.fm Page 7 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011

Rosemount 3051SMV

STEP 2: CONSIDER HOUSING ROTATION

To improve field access to wiring or to

better view the optional LCD display: Figure 4. Transmitter Housing

Set Screw

1. Loosen the housing rotation set

screw.

2. Turn the housing up to 180° left or

right of its original (as shipped)

position.

3. Retighten the housing rotation set

screw.

NOTE

Do not rotate the housing more than 180° without first performing a

disassembly procedure (see Section 4 of the 3051S MultiVariable transmitter

reference manual (00809-0100-4803) for more information). Over-rotation

may sever the electrical connection between the sensor module and the

feature board electronics.

Housing Rotation Set Screw

(3/32-in.)

Feature

Board

4803_QIG_RevBA.fm Page 8 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011 Rosemount 3051SMV

STEP 3: SET SWITCHES

The transmitter’s default configuration sets the alarm condition to high

(HI) and the security to off.

1. If the transmitter is installed, secure the loop and remove power.

2. Remove the housing cover opposite the field terminals side. Do not

remove the housing cover in explosive environments.

3. Slide the security and alarm switches into the preferred position by

using a small screwdriver.

4. Reinstall the housing cover so that metal contacts metal to meet

explosion-proof requirements.

Figure 5. Transmitter Switch Configuration

Alarm

Security

4803_QIG_RevBA.fm Page 9 Monday, April 25, 2011 2:37 PM

Quick Installation Guide

00825-0100-4803, Rev BA

April 2011

Rosemount 3051SMV

STEP 4: CONNECT WIRING AND POWER UP

NOTE

Do not connect the power across the test terminals. Power could damage the

test diode in the test connection. Twisted pairs yield best results. Use 24 AWG to

14 AWG wire and do not exceed 5,000 feet (1500 meters).

Use the following steps to wire the transmitter:

1. Remove the cover on the field terminals side of the housing.

2. Connect the positive lead to the “PWR/COMM +” terminal, and the

negative lead to the “PWR/COMM –” terminal.

3. If the optional process temperature input is not installed, plug and

seal the unused conduit connection. If the optional process

temperature input is being utilized, see “Install Optional Process

Temperature Input (Pt 100 RTD Sensor)” on page 13 for more

information.

IMPORTANT NOTICE

4. If applicable, install wiring with a drip loop. Arrange the drip loop

so the bottom is lower than the conduit connections and the

transmitter housing.

5. Reinstall the housing cover and tighten so that metal contacts

metal to meet explosion-proof requirements.

When the enclosed pipe plug is utilized in the conduit opening, it must be

installed with a minimum engagement of five threads in order to comply with

explosion-proof requirements. Refer to the 3051S MultiVariable transmitter

reference manual (document number 00809-0100-4803) for more information.

4803_QIG_RevBA.fm Page 10 Monday, April 25, 2011 2:37 PM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rosemount Émetteur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount 3144P Manuel utilisateur

Rosemount

Rosemount Oxymitter 4000 Manuel de formation

Rosemount

Rosemount OCX 8800 Manuel utilisateur

Rosemount

Rosemount 3144 Manuel utilisateur

Rosemount

Rosemount 248 Manuel utilisateur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount 8712 Manuel utilisateur

Rosemount

Rosemount 3107 Mode d’emploi

Rosemount

Rosemount 8732 Series Manuel utilisateur

Rosemount

Rosemount 2051CF Series Manuel utilisateur

Rosemount

Rosemount 1199 Manuel utilisateur

Rosemount

Rosemount 3051 Manuel utilisateur

Rosemount

Rosemount 3152 Manuel utilisateur

Rosemount

Rosemount 148 Manuel utilisateur

Rosemount

Rosemount 8732E Manuel utilisateur

Rosemount

Rosemount 248 Manuel utilisateur

Rosemount

Rosemount 3095MF Series Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Rosemount

Rosemount 3051 Manuel utilisateur

Rosemount

Rosemount 4088A MultiVariable Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Rosemount

Rosemount 702 Manuel utilisateur

Rosemount

Rosemount 848T Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur