Rosemount 148 Manuel utilisateur

Quick Start Guide

00825-0100-4148, rev. DA

April 2013

Rosemount 148 Temperature

Transmitter

00825-0100-4148_Rev_DA.fm Page 1 Tuesday, April 2, 2013 1:31 PM

April 2013

Quick Start Guide

NOTICE

This installation guide provides basic guidelines for the Rosemount 148. It does not provide instructions for

detailed configuration, diagnostics, maintenance, service, troubleshooting, or installations. Refer to the

Rosemount 148 Reference Manual (Document No. 00809-0100-4148) for more instruction. The manual and

this QIG are also available electronically on www.rosemount.com.

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Please review the Hazardous Locations

Certifications for any restrictions associated with a safe installation.

Process leaks may cause harm or result in death

Install and tighten thermowells or sensors before applying pressure.

Do not remove the thermowell while in operation.

Electrical shock can result in death or serious injury

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause electrical

shock.

Conduit/Cable Entries

Unless marked, the conduit/cable entries in the transmitter housing use a 1/2-14 NPT thread form. Entries

marked "M20" are M20 x 1.5 thread form. On devices with multiple conduit entries, all entries have the same

thread form. Only use plugs, adapters, glands, or conduit with a compatible thread form when closing

entries.

When installing in a Hazardous Location, use only appropriately listed or Ex certified plugs, adapters or

glands in cable/conduit entries.

Contents

Software installation . . . . . . . . . page 3

Configure . . . . . . . . . . . . . . . . . . page 3

Mount the transmitter . . . . . . . page 4

Connect the wiring . . . . . . . . . .page 7

Product Certifications . . . . . . page 10

148 PC Programmer License Agreement

page 17

00825-0100-4148_Rev_DA.fm Page 2 Tuesday, April 2, 2013 1:31 PM

Quick Start Guide

April 2013

Step 1: Software installation

1. Install the 148 PC Programmer software.

Place the 148 PC Programmer CD_ROM into the drive

Run setup.exe from Windows NT, 2000, or XP

2. When first using the 148 PC software, configure the appropriate COM ports by

selecting “Port Settings” from the “Communicate” menu.

3. Install MACTek Modem drivers completely before beginning bench

configuration on the Rosemount 148 system.

Note:

The software defaults to the first available COM port.

Step 2: Configure

The Rosemount 148 must be configured for certain basic variables to operate. In

many cases, all of these variables are pre-configured at the factory. Configuration

may be required if the transmitter is not configured or if the configuration

variables need revision. This can be done in two ways: by ordering

factory-configuration by Emerson, or by using the Rosemount 148 PC

Programming interface in a bench configuration setting.

The Rosemount 148 PC Programming Kit includes configuration software and a

communication modem. The Rosemount 148 device will need an external power

supply of 12-42.4 Vdc for configuration.

1. Hook up the transmitter and a load resistor (250- 1100 ohms) wired in series

with the power supply.

2. Attach the Modem in parallel with the load resistor and connect it to the PC.

Please see Table 1 for Spares Kit and re-order numbers. For more information,

refer to the Rosemount 148 Reference Manual (Document No.

00809-0100-4148).

Table 1. Rosemount 148 Programming Kit Spare Part numbers

Verify transmitter configuration

If the transmitter has been connected to a sensor (either a test or installation

mounting hardware), the configuration can be checked using the Information tab

on the 148 PC Programmer interface. Click Refresh to update the status and

confirm that the transmitter has been configured correctly. If there are any

problems, refer to the Reference Manual for troubleshooting suggestions.

Product Description Part Number

Programming Software (CD) 00148-1601-0002

Rosemount 148 Programmer Kit - USB 00148-1601-0003

Rosemount 148 Programmer Kit - Serial 00148-1601-0004

00825-0100-4148_Rev_DA.fm Page 3 Tuesday, April 2, 2013 1:31 PM

April 2013

Quick Start Guide

Step 3: Mount the transmitter

To prevent moisture from draining into the transmitter housing, mount the

transmitter at a high point in the conduit run.

Typical European and Asia Pacific installation

Head Mount Transmitter with DIN plate style sensor

1. Attach the thermowell to the pipe or process container wall. Install and

tighten the thermowell before applying process pressure.

2. Assemble the transmitter to the sensor. Push the transmitter mounting

screws through the sensor mounting plate and insert the snap rings (optional)

into the transmitter mounting screw groove.

3. Wire the sensor to the transmitter.

4. Insert the transmitter-sensor assembly into the connection head. Thread the

transmitter mounting screw into the connection head mounting holes.

Assemble the extension to the connection head. Insert the assembly into the

thermowell.

5. Slip the shielded cable through the cable gland

6. Attach a cable gland into the shielded cable.

7. Insert the shielded cable leads into the connection head through the cable

entry. Connect and tighten the cable gland.

8. Connect the shielded power cable leads to the transmitter power terminals.

Avoid contact with sensor leads and sensor connections. (See Step 4 for

instructions on grounding the shield wire.)

9. Install and tighten the connection head cover. Enclosure covers must be fully

engaged to meet explosion-proof requirements.

00825-0100-4148_Rev_DA.fm Page 4 Tuesday, April 2, 2013 1:31 PM

Quick Start Guide

April 2013

Step 3 continued...

Typical North and South American installation

Head Mount Transmitter with Threaded Sensor

1. Attach the thermowell to the pipe or process container wall. Install and tighten

thermowells before applying process pressure.

2. Attach necessary extension nipples and adapters to the thermowell. Seal the

nipple and adapter threads with silicone tape.

3. Screw the sensor into the thermowell. Install drain seals if required for severe

environments or to satisfy code requirements.

4. Pull the sensor wiring leads through the universal head and transmitter. Mount

the transmitter in the universal head by threading the transmitter mounting

screws into the universal head mounting holes.

5. Mount the transmitter-sensor assembly into the thermowell. Seal adapter

threads with silicone tape.

6. Install conduit for field wiring to the conduit entry of the universal head. Seal

conduit threads with silicone tape.

7. Pull the field wiring leads through the conduit into the universal head. Attach

the sensor and power leads to the transmitter. Avoid contact with other

terminals.

8. Install and tighten the universal head cover. Enclosure covers must be fully

engaged to meet explosion-proof requirements

A = Rosemount 148 Transmitter D = Transmitter Mounting Screws

B = Connection Head E = Integral Mount Sensor with Flying Leads

C = Thermowell F = Extension

00825-0100-4148_Rev_DA.fm Page 5 Tuesday, April 2, 2013 1:31 PM

April 2013

Quick Start Guide

Step 3 continued...

Mounting to a DIN Rail

A = Threaded Thermowell D = Universal Head

B = Threaded Style Sensor E = Conduit Entry

C = Standard Extension

To attach the Rosemount 148H to a

DIN rail, assemble the appropriate

rail mounting kit (part number

00248-1601-0001) to the

transmitter as shown.

Transmitter

Mounting

Hardware

Rail Clip

00825-0100-4148_Rev_DA.fm Page 6 Tuesday, April 2, 2013 1:31 PM

Quick Start Guide

April 2013

Step 4: Connect the wiring

Wiring diagrams are located on the top label of the transmitter.

An external power supply is required to operate the transmitter.

The power required across the transmitter power terminals is 12 to 42.4 Vdc

(the power terminals are rated to 42.4 Vdc). To prevent damaging the

transmitter, do not allow terminal voltage to drop below 12.0 Vdc when

changing the configuration parameters.

Power the transmitter

1. Connect the positive power lead to the “+” terminal. Connect

the negative power lead to the “–” terminal.

2. Tighten the terminal screws.

3. Apply power (12 – 42 Vdc).

Figure 1. Power, Communication, and Sensor Terminals

Ground the transmitter

Ungrounded Thermocouple, and RTD/Ohm Inputs

Each process installation has different requirements for grounding. Use the

grounding options recommended by the facility for the specific sensor type or

begin with grounding Option 1 (the most common).

Sensor

Terminals

Power/Communication

Terminals

00825-0100-4148_Rev_DA.fm Page 7 Tuesday, April 2, 2013 1:31 PM

April 2013

Quick Start Guide

Step 4 continued...

Option 1 (for grounded housing):

1. Connect sensor wiring shield to the transmitter housing.

2. Ensure the sensor shield is electrically isolated from surrounding fixtures that

may be grounded.

3. Ground signal wiring shield at the power supply end.

Option 2 (for ungrounded housing):

1. Connect signal wiring shield to the sensor wiring shield.

2. Ensure the two shields are tied together and electrically isolated from the

transmitter housing.

3. Ground shield at the power supply end only.

Ensure that the sensor shield is electrically isolated from the surrounding

grounded fixtures.

4–20 mA loop

Sensor Wires

Shield ground point

Transmitter

Sensor Wires 4–20 mA loop

Shield ground point

Connect shields together, electrically isolated from the transmitter

Transmitter

00825-0100-4148_Rev_DA.fm Page 8 Tuesday, April 2, 2013 1:31 PM

Quick Start Guide

April 2013

Step 4 continued...

Option 3 (for grounded or ungrounded housing):

1. Ground sensor wiring shield at the sensor, if possible.

2. Insure that the sensor wiring and signal wiring shields are electrically isolated

from the transmitter housing.

3. Do not connect the signal wiring shield to the sensor wiring shield.

4. Ground signal wiring shield at the power supply end.

Grounded Thermocouple Inputs

Option 4

1. Ground sensor wiring shield at the sensor.

2. Ensure that the sensor wiring and signal wiring shields are electrically isolated

from the transmitter housing.

3. Do not connect the signal wiring shield to the sensor wiring shield.

4. Ground signal wiring shield at the power supply end.

4–20 mA loop

Sensor Wires

Shield ground point

Transmitter

4–20 mA loop

Sensor Wires

Shield ground point

Transmitter

00825-0100-4148_Rev_DA.fm Page 9 Tuesday, April 2, 2013 1:31 PM

April 2013

Quick Start Guide

Product Certifications

European Union Directive Information

This product complies with the ATEX directive and EN 61326-2-3:2006 and EN

61326-1:2006 EMC Directives for more detailed information, consult the

European Declaration of Conformity Section in this document.

ATEX Directive (94/9/EC)

Rosemount Inc. complies with the ATEX Directive.

Electro Magnetic Compatibility (EMC) (89/336/EEC)

All Models: EN 50081-1: 1992; EN 50082-2: 1995; EN 61326-1: 2006 – Industrial

NAMUR NE21 Recommendations

The Rosemount 148 meets the requirements for NAMUR NE21 Rating

CE Mark

The Rosemount 148 meets all requirements listed under IEC 61326:Amendment

1, 2006

Susceptibility Parameter Influence

ESD 6 kV contact discharge

8 kV air discharge None

Radiated 80 – 1000 MHz at 10 V/m AM None

Burst 1 kV for I.O. None

Surge 0.5 kV line–line

1 kV line–ground (I.O. tool) None

Conducted 150 kHz to 80 MHz at 10 V None

00825-0100-4148_Rev_DA.fm Page 10 Tuesday, April 2, 2013 1:31 PM

Autres manuels pour 148

Table des matières

Autres manuels Rosemount Émetteur

Rosemount

Rosemount 248 Manuel utilisateur

Rosemount

Rosemount 8712C Manuel utilisateur

Rosemount

Rosemount 848T Manuel utilisateur

Rosemount

Rosemount 2051 Manuel utilisateur

Rosemount

Rosemount FISHER-ROSEMOUNT 244EH Manuel utilisateur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount 3095MF Series Manuel utilisateur

Rosemount

Rosemount 3051SMV Manuel utilisateur

Rosemount

Rosemount 3051S Series Manuel utilisateur

Rosemount

Rosemount 3152 Manuel utilisateur

Rosemount

Rosemount 248 Manuel utilisateur

Rosemount

Rosemount 2088 Manuel utilisateur

Rosemount

Rosemount 3051 Manuel utilisateur

Rosemount

Rosemount 3051 Manuel utilisateur

Rosemount

Rosemount 848T Manuel utilisateur

Rosemount

Rosemount OCX 8800 Manuel utilisateur

Rosemount

Rosemount 8732 Series Manuel utilisateur

Rosemount

Rosemount 1199 Manuel utilisateur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount 3107 Mode d’emploi

Rosemount

Rosemount Oxymitter 4000 Manuel de formation

Rosemount

Rosemount 8732E Manuel utilisateur

Rosemount

Rosemount 3144P Manuel utilisateur

Rosemount

Rosemount 3244MV Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur