Rosemount 708 Manuel utilisateur

www.rosemount.com

Reference Manual

00809-0100-4708, Rev AA

June 2010

Rosemount 708 Wireless Acoustic

Transmitter

Reference Manual

00809-0100-4708, Rev AA

June 2010 Rosemount 708

Rosemount 708 Wireless

Acoustic Transmitter

Rosemount 708 Hardware Revision

HART®Device Revision

Field Communicator Field Device Revision

Dev vX, DD vX

NOTICE

Read this manual before working with the product. For personal and system safety, and for

optimum product performance, make sure to thoroughly understand the contents before

installing, using, or maintaining this product.

The United States has two toll-free assistance numbers and one international number.

Customer Central

1 800 999 9307 (7:00 a.m. to 7:00 p.m. CST)

National Response Center

1 800 654 7768 (24 hours a day)

Equipment service needs

International

1 952 906 8888

The products described in this document are NOT designed for nuclear-qualified

applications.

Using non-nuclear qualified products in applications that require nuclear-qualified hardware

or products may cause inaccurate readings.

For information on Rosemount nuclear-qualified products, contact an Emerson Process

Management Sales Representative.

Reference Manual

00809-0100-4708, Rev AA

June 2010

Rosemount 708

The power module with the wireless unit contains one "D” size primary lithium/thionyl chloride

batteries. Each battery contains approximately X.X grams of lithium. Under normal conditions,

the battery materials are self-contained and are not reactive as long as the batteries and the pack

integrity are maintained. Care should be taken to prevent thermal, electrical or mechanical

damage. Contacts should be protected to prevent premature discharge.

Battery hazards remain when cells are discharged.

Power modules should be stored in a clean and dry area. For maximum battery life, storage

temperature should not exceed 30° C.

The power module has surface resistivity greater than one gigaohm and must be properly

installed in the wireless device enclosure. Care must be taken during transportation to and from

the point of installation to prevent electrostatic charge build-up.

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance

with the appropriate local, national, and international standards, codes, and

practices. Please review the approvals section of the 708 Reference Manual for any

restrictions associated with a safe installation.

• Before connecting a Field Communicator in an explosive atmosphere, ensure the

instruments are installed in accordance with intrinsically safe or non-incendive

field wiring practices

Process leaks may cause harm or result in death:

• Install and tighten process connectors before applying pressure

Electrical shock can result in death or serious injury:

• Avoid contact with the leads and terminals. High voltage that may be present on

leads can cause electrical shock

NOTICE

The Rosemount 708 and all other wireless devices should be installed only after the

Smart Wireless Gateway has been installed and is functioning properly. Wireless

devices should also be powered up in order of proximity from the Smart Wireless

Gateway, beginning with the closest. This will result in a simpler and faster network

installation.

NOTICE

Shipping considerations for wireless products:

The unit was shipped to you without the power module installed. Please remove the power

module prior to shipping.

Each power module contains one “D” size primary lithium battery. Primary lithium batteries

are regulated in transportation by the U. S. Department of Transportation, and are also

covered by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the

responsibility of the shipper to ensure compliance with these or any other local

requirements. Please consult current regulations and requirements before shipping.

Reference Manual

00809-0100-4708, Rev AA

June 2010

TOC-1

Rosemount 708

SECTION 1

Overview Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

SECTION 2

Configuration Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Device Sensor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Device Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Remove Power Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

SECTION 3

Mounting Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

SECTION 4

Commissioning Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Verify Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

SECTION 5

Operation and

Maintenance

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Power Module Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

APPENDIX A

Specifications and

Reference Data

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

APPENDIX B

Product

Certifications

Table of Contents

Reference Manual

00809-0100-4708, Rev AA

June 2010

Rosemount 708

TOC-2

Reference Manual

00809-0100-4708, Rev AA

June 2010

1-1

Rosemount 708

Section 1 Overview

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-2

Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-3

Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 1-4

Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . .page 1-5

SAFETY MESSAGES Instructions and procedures in this section may require special precautions to

ensure the safety of the personnel performing the operations. Information that

potentially raises safety issues is indicated by a warning symbol ( ). Please

refer to the following safety messages before performing an operation

preceded by this symbol.

Warnings

Failure to follow these installation guidelines could result in death or serious injury:

• Only qualified personnel should perform the installation

Explosions could result in death or serious injury.

• Before connecting a Field Communicator in an explosive atmosphere, make

sure that the instruments are installed in accordance with intrinsically safe or

non-incendive field wiring practices

• Verify that the operating atmosphere of the transmitter is consistent with the

appropriate hazardous locations certifications

Electrical shock could cause death or serious injury.

• Use extreme caution when making contact with the leads and terminals

Reference Manual

00809-0100-4708, Rev AA

June 2010

Rosemount 708

1-2

OVERVIEW

Manual This manual is designed to assist in the installation, operation, and

maintenance of the Rosemount 702.

Section 1: Overview

• Overview

• Considerations

• Service Support

• Product Recycling/Disposal

Section 2: Configuration

• Device Sensor Configuration

• Device Network Configuration

• Remove Power Module

Section 3: Mounting

• Mounting

- Direct Mount

• Ground the Transmitter

Section 4: Commissioning

• Verify Operation

•AMS

®Wireless Configurator

Section 5: Operation and Maintenance

• Power Module Replacement

Section A: Specifications and Reference Data

• Specifications

• Dimensional Drawings

• Ordering Information

Section B: Product Certifications

• Approved Manufacturing Locations

• Telecommunication Compliance

• FCC and IC

• European Union Directive Information

• Ordinary Location Certification for FM

• Hazardous Locations Certificates

Transmitter Features of the Rosemount 708 include:

• An installation-ready solution that provides acoustic noise detection.

• Acoustic levels to verify the state of steam traps, pressure relief valves,

condensers, and many others.

• Wireless output with >99% data reliability delivers rich HART®data,

protected by industry leading security

• Simple and easy installation practices currently being used for robust

installations

Reference Manual

00809-0100-4708, Rev AA

June 2010

1-3

Rosemount 708

CONSIDERATIONS

General The acoustic transmitter detects either a noise or no noise along with a

temperature. By using simple HART configuration, the Rosemount 708

converts the noise and temperature status to a device status.

Wireless Considerations Power Up Sequence

The power module should not be installed on any wireless device until the

Smart Wireless Gateway (“Gateway”) is installed and functioning properly.

Wireless devices should also be powered up in order of proximity from the

Gateway, beginning with the closest. This will result in a simpler and faster

network installation. Enable Active Advertising on the Gateway to ensure that

new devices join the network faster. For more information see the Smart

Wireless Gateway Manual (Document Number 00809-0200-4420).

Antenna Position

The antenna is internal to the acoustic transmitter. If best practices are

followed, the antenna position will not matter in the wireless functionality.

Field Communicator Connections

The Power Module needs to be connected for the Field Communicator to

interface with the 708.

Figure 1-1.

Mechanical Location

When choosing an installation location and position, take into account access

to the transmitter.

Reference Manual

00809-0100-4708, Rev AA

June 2010

Rosemount 708

1-4

Electrical Power Module

The Rosemount 708 Wireless transmitter is self-powered. The included power

module contains one “D” size primary lithium/thionyl chloride battery. Each

battery contains approximately X.X grams of lithium. Under normal conditions,

the battery materials are self-contained and are not reactive as long as the

batteries and the power module are maintained. Care should be taken to

prevent thermal, electrical, or mechanical damage. Contacts should be

protected to prevent premature discharge.

Use caution when handling the power module, it may be damaged if dropped

from heights in excess of 20 feet (6.10 m).

Environmental Verify that the operating atmosphere of the transmitter is consistent with the

appropriate hazardous locations certifications.

Temperature Effects

The transmitter will operate within specifications for ambient temperatures

between -40 and 185 °F (-40 and 85 °C). Heat from the process is transferred

from the switch to the transmitter housing. If the expected process

temperature is near or beyond specification limits, ...add recommendation

Temperature Limits

SERVICE SUPPORT To expedite the return process outside of North America, contact your

Emerson Process Management representative,

Within the United States, call the Emerson Process Management Response

Center toll-free number 1 800 654 7768. The center, which is available 24

hours a day, will assist you with any needed information or materials.

The center will ask for product model and serial numbers, and will provide a

Return Material Authorization (RMA) number. The center will also ask for the

process material to which the product was last exposed.

SHIPPING CONSIDERATIONS FOR WIRELESS PRODUCTS (LITHIUM

BATTERIES):

The unit was shipped with the Power Module not installed. Please remove the

Power Module from the unit before shipping.

Primary lithium batteries (charged or discharged) are regulated during

transportation by the U.S. Department of Transportation. They are also

Operating Limit Storage Limit

-40 to 185 °F

-40 to 85° C -40 to 185 °F

-40 to 85 °C

Individuals who handle products exposed to a hazardous substance can avoid injury if they

are informed of, and understand, the hazard. If the product being returned was exposed to a

hazardous substance as defined by OSHA, a copy of the required Material Safety Data

Sheet (MSDS) for each hazardous substance identified must be included with the returned

goods.

Table des matières

Autres manuels Rosemount Émetteur

Rosemount

Rosemount 848T Manuel utilisateur

Rosemount

Rosemount 3152 Manuel utilisateur

Rosemount

Rosemount 3051S Series Manuel utilisateur

Rosemount

Rosemount 4088A MultiVariable Manuel utilisateur

Rosemount

Rosemount 8732 Series Manuel utilisateur

Rosemount

Rosemount 3051SMV Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Rosemount

Rosemount Oxymitter 5000 Manuel utilisateur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount FISHER-ROSEMOUNT 244EH Manuel utilisateur

Rosemount

Rosemount 3300 Series Manuel utilisateur

Rosemount

Rosemount 3051 Manuel utilisateur

Rosemount

Rosemount OCX 8800 Manuel utilisateur

Rosemount

Rosemount 3144P Manuel utilisateur

Rosemount

Rosemount 848T Manuel utilisateur

Rosemount

Rosemount 3144P Manuel utilisateur

Rosemount

Rosemount Oxymitter 4000 Manuel de formation

Rosemount

Rosemount 2051 Manuel utilisateur

Rosemount

Rosemount 3108 Manuel utilisateur

Rosemount

Rosemount 2051CF Series Manuel utilisateur

Rosemount

Rosemount 3107 Mode d’emploi

Rosemount

Rosemount 8712C Manuel utilisateur

Rosemount

Rosemount 8732E Manuel utilisateur

Rosemount

Rosemount 248 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur