Protech Prox PA-J511 Manuel utilisateur

USER

MANUAL

PA-J511

15" High Performance

POS Terminal

PA-J511M2

PA-J511 15” High

Performance POS Terminal

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

This manual is copyrighted in Apr. 2023. You may not reproduce or

transmit in any form or by any means, electronic, or mechanical,

including photocopying and recording.

DISCLAIMER

This user’smanual is meant to assist users in installing and setting up

the system. The information contained in this document is subject to

change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required totake

adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment

not expressly approve by the party responsible for compliance could

void your authority to operate such equipment.

CAUTION: Danger of explosion may occur when the battery

is incorrectly replaced. Replace the battery

only with the

same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

WARNING: Some internal parts of the system may have

high electrical voltage. We strongly recommend that only

qualified engineers are allowed to service and disassemble

the system. If any damages should occur on the system and

are caused by unauthorized servicing, it will not be covered

by the product warranty.

Contents

Revision History ............................................................................................. v

1Introduction ......................................................................................... 1-1

1.1 About This Manual ..................................................................... 1-2

2Getting Started .................................................................................... 2-1

2.1 Package List............................................................................... 2-2

2.2 System Overview ....................................................................... 2-3

2.2.1 Panel PC ............................................................................. 2-3

2.2.2 Normal Stand Only.............................................................. 2-4

2.2.3 Normal Stand with 10.1" 2nd Display ................................. 2-5

2.3 System Specifications ................................................................ 2-6

2.4 Safety Precautions ..................................................................... 2-8

3System Configuration......................................................................... 3-1

3.1 System External I/O Ports Diagram ........................................... 3-2

3.2 Mainboard Component Locations & Jumper Setting ................. 3-3

3.3 How to Set Jumpers................................................................... 3-4

3.4 Main Board Connector & Jumper Quick Reference Table ......... 3-6

3.5 Setting Main Board Connectors and Jumpers ........................... 3-7

3.5.1 Power Switch ...................................................................... 3-7

3.5.2 DC IN Connector (DC In) .................................................... 3-7

3.5.3 1st Display Port (MDP1) ..................................................... 3-8

3.5.4 COM Ports (COM1, COM2) ................................................ 3-9

3.5.5 COM Connector (COM3, COM4)........................................ 3-9

3.5.6 LAN Port (LAN1) ............................................................... 3-11

3.5.7 USB 2.0 Port (USB4) ........................................................3-12

3.5.8 Dual USB 2.0 Ports (USB2).............................................. 3-13

3.5.9 Dual USB 3.0 Ports (USB1).............................................. 3-13

3.5.10 2nd Display Port (MDP2) .................................................. 3-14

3.5.11 HDMI Port Connector (HDMI1).........................................3-15

3.5.12 Cash Drawer Port (DRW) .................................................3-16

3.5.13 Internal USB Wafer (JUSB9) ............................................3-19

3.5.14 Internal USB Wafer (JUSB7) ............................................3-20

3.5.15 M.2 M-Key Connector for SSD (M2_M1)..........................3-21

3.5.16 M.2 M-Key Connector for SSD (M2_M2)..........................3-23

3.5.17 M.2 E-Key Connector for Wi-Fi (M2_E1) ..........................3-25

3.5.18 Speaker Wafer (JSPK1).................................................... 3-27

3.5.19 Microphone Connector (JMIC1)........................................ 3-27

3.5.20 Power Output 24V Wafer (J24V_OUT1)........................... 3-27

3.5.21 System LED Wafer (JSYS_LED1) .................................... 3-28

3.5.22 CPU Fan Wafer (CPU_FAN1)...........................................3-28

3.5.23 Power Button Wafer (JPWRBTN1) ................................... 3-29

3.5.24 Battery Wafer (JBAT1) ......................................................3-29

3.5.25 System Reset Wafer (JRST1)........................................... 3-29

3.5.26 Cash Drawer Voltage Selection (JP3) ..............................3-30

3.5.27 Clear CMOS Data Selection (JCMOS1) ...........................3-31

3.6 A/D Board Component Locations & Jumper Setting................3-32

3.7 A/D Board Connector & Jumper Quick Reference Table .........3-33

3.8 Setting A/D Board Connectors and Jumpers ........................... 3-34

3.8.1 1st Display Port Connector (MDP1).................................. 3-34

3.8.2 Embedded DisplayPort Connector (JEDP2).....................3-35

3.8.3 Speaker Connector (JSPK1) ............................................3-36

3.8.4 Inverter Connector (JINV1)............................................... 3-36

3.8.5 LVDS Connector (LVDS1).................................................3-37

3.8.6 USB 2.0 Connector (JUSB1, JUSB2, JUSB3)..................3-38

iii

3.8.7 Backlight Voltage Selection (JP_INV1).............................3-39

3.8.8 LVDS Panel Voltage Control Selection (JP_VDD1).......... 3-39

3.8.9 LVDS Backlight Control Selection (JP1) ........................... 3-40

4Software Utilities................................................................................. 4-1

4.1 Introduction................................................................................. 4-2

4.1.1 Installing Intel®Chipset Software Installation Utility ........... 4-3

4.1.2 Installing Graphics Driver Utility.......................................... 4-4

4.1.3 Intel®Management Engine Components Installer Installation.

........................................................................................... 4-5

4.1.4 Installing LAN Driver Utility ................................................. 4-6

4.1.5 Installing Sound Driver Utility.............................................. 4-7

5BIOS SETUP ........................................................................................ 5-1

5.1 Introduction................................................................................. 5-2

5.1.1.1 Accessing Setup Utility ................................................... 5-4

5.1.2 Main .................................................................................... 5-7

5.1.3 Advanced ............................................................................ 5-8

5.1.3.1 Advanced - CPU Configuration..................................... 5-10

5.1.3.2 Advanced - PCH-FW Configuration.............................. 5-11

5.1.3.3 Advanced - Trusted Computing ....................................5-12

5.1.3.4 Advanced - ACPI Settings ............................................ 5-13

5.1.3.5 Advanced - F81967 Super IO Configuration ................ 5-14

5.1.3.6 Advanced - Hardware Monitor ...................................... 5-19

5.1.3.7 Advanced - F81967 Watchdog .....................................5-22

5.1.3.8 Advanced - S5 RTC Wake Settings.............................. 5-23

5.1.3.9 Advanced - USB Configuration..................................... 5-24

5.1.3.10 Advanced - Network Stack Configuration ..................... 5-25

5.1.3.11 Advanced - NVMe Configuration ..................................5-26

5.1.4 Chipset ..............................................................................5-27

5.1.4.1 System Agent (SA) Configuration ................................. 5-28

5.1.4.2 PCH IO Configuration ...................................................5-30

5.1.5 Security ............................................................................. 5-36

5.1.6 Boot................................................................................... 5-38

5.1.7 Save & Exit ....................................................................... 5-40

Appendix A System Diagrams....................................................A-1

PPC Memory Maintenance.......................................................................A-2

PPC M.2 2280 Maintenance.....................................................................A-4

PA-J511 Memory Maintenance ................................................................A-5

PA-J511 M.2 2280 Maintenance ..............................................................A-7

How To Turn System Touchscreen ...........................................................A-8

2nd Display Assembly ..............................................................................A-9

VFD Module Assembly ...........................................................................A-12

iButton Module Assembly .......................................................................A-14

Fingerprint Module Assembly .................................................................A-15

Barcode Scanner Assembly ...................................................................A-16

MSR Module Assembly ..........................................................................A-17

POS Type Assembly Exploded Diagram ................................................A-18

PPC Type Assembly Exploded Diagram ................................................A-19

Appendix B Technical Summary ................................................B-1

Block Diagram ..........................................................................................B-2

Interrupt Map ............................................................................................B-3

I/O MAP ..................................................................................................B-18

Memory Map...........................................................................................B-20

Configuring WatchDog Timer .................................................................B-22

Flash BIOS Update.................................................................................B-26

Revision History

The revision history of PA-J511 User Manual isdescribed below:

Version No. Revision History Date

M2 The description of Section 3.5.12 Cash Drawer

Port (DRW) has been revised. (Page 3-16) 2023/04/25

M1 Initial Release 2023/4/10

PA -J511SERIES USER MANUAL

Page: 1-1

1Introduction

This chapter provides the introduction for PA-J511 system

as well as the framework ofthe user manual.

The following topic is included:

•About This Manual

Chapter 1 Introduction

PA -J511SERIES USER MANUAL

Page: 1-2

1.1 About ThisManual

Thank you for purchasing our PA-J511system. The PA-J511is an updated system

designed to be comparable with the highest performance of IBM AT

personal computers. The PA-J511provides faster processing speed, greater

expandability and can handle more tasks than before. This manual is designed to

assist you how to install and set up the whole system. It contains 5 chapters and 2

appendixes. Users can configure the system according to their own needs. This user

manual is intended for service personnel with strong hardware background. It is

not intended for general users.

The following section describes the structure of this user manual.

Chapter 1 Introduction

This chapter introduces the framework of this user manual.

Chapter 2 Getting Started

This chapter describes the package contents and system specifications,and illustrates

the physical appearances for PA-J511system. Read the safety reminders carefully on

how to take care of your system properly.

Chapter 3 System Configuration

This chapter describes the locations and functions of the system main board

components. You will learn how toproperly configure the connectors and system

configuration jumpers on the main board and configure the system tomeet your own

needs.

Chapter 4 Software Utilities

This chapter introduces how to install Intel Chipset Software Installation Utility,

Graphics Driver Utility, Intel Management Engine Components Installer Driver

Utility, LAN Driver Utility, Serial IO Driver Utility and Sound Driver Utility.

Chapter 5 BIOS Setup

This chapter provides BIOS setup information.

Appendix A System Diagrams

This appendix provides the exploded diagrams and part numbers of PA-J511.

Appendix B Technical Summary

This appendix provides the information about the system block diagram, allocation

maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.

Autres manuels pour prox PA-J511

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels protech Terminal tactile

protech

protech prox PA-R120 Manuel utilisateur

protech

protech prox PA-J580 Manuel utilisateur

protech

protech prox PA-J510 Manuel utilisateur

protech

protech PA-6980 Series Manuel utilisateur

protech

protech PA-3110 Manuel utilisateur

protech

protech PA-1922 Manuel utilisateur

protech

protech KS-M320 Manuel utilisateur

protech

protech PA-J501 Manuel utilisateur

protech

protech prox PA-J581 Manuel utilisateur

protech

protech PA-3211 Manuel utilisateur

protech

protech PA-3055 Manuel utilisateur

protech

protech prox PA-A900 Manuel utilisateur

protech

protech prox PA-A310 Manuel utilisateur

protech

protech POS-3152 Series Manuel utilisateur

protech

protech PS-8851A Manuel utilisateur

protech

protech prox PA-J511 Manuel utilisateur

protech

protech PA-6610 Manuel utilisateur

protech

protech KF-7130 Manuel utilisateur

protech

protech PS3100 Series Manuel utilisateur

protech

protech POS-3120 Series Manuel utilisateur

protech

protech PA-2019 Series Manuel utilisateur

protech

protech prox PA-J500 Manuel utilisateur

protech

protech PA-A901 Manuel utilisateur

protech

protech prox PA-J510 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur