Premier Mounts EST100 Manuel utilisateur

Single-Stud/Dual-Stud

Short-Throw Projector Wall Mount

Model: EST100/EST200

9530-011-001-00

INSTALLATION INSTRUCTIONS

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada

Phone: 1-800-368-9700

Fax: 1-800-832-4888

Other Locations

Phone: (001) 714-632-7100

Fax: (001) 714-632-1044

EUROPE

Swallow House,

Shilton Industrial Estate,

Shilton, Coventry, England CV79JY

Phone: +44 (0) 2476 614700

Fax: +44 (0) 2476 614710

Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions

Table of Contents

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR

PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR

MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION

OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR

MODIFICATIONS.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER

SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the

projector.

If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is

recommended.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in

wall. Cutting/drilling into an electrical line may cause serious injury.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact

Contact Premier Mounts with any questions

(800) 368-9700

[email protected]

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN-

DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP

THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water

damage to the mounting surface.

EST100/EST200

Weight Capacity

Maximum projector weight: 25 lbs. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE

(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE

WALL STRUCTURE MUST BE REINFORCED.

Warning Statements

Heading 1

Weight Capacity 2

Warning Statements 2

Installation Tools 3

Parts List 3

Features 4

Determining the Installation Height 5

Wood Stud Installation 6

Throw Distance Calculation 10

Projector Installation 10

Attaching the Mount Carriage 11

Multiple Mounting Point Installation 12

Single Mounting Point Installation 14

Attaching the Mount Carriage to the Projector Arm 15

Cable Routing (Optional) 16

Securing the Projector (Optional) 16

Mount Adjustment 17

Technical Specications 17

Warranty 18

Disclaimer 18

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3

Projector Arm

(Qty 1)

Mount Carriage

(Qty 1)

Phillips Screwdriver ⅛˝ Drill Bit Electronic Stud Finder

Drill Level

Dual-Stud Back Plate

(Qty 1)

EST100/EST200

Back Plate Hardware Pack (included only with the EST200)

Parts List

Installation Tools

The following tools may be required depending upon your particular installation. They are not included.

Make sure your Premier Mounts product has the following hardware and components before beginning installation. If

there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.

EST100/EST200 Hardware

M2.5 x 8mm

Security Screw (Qty 4)

M2.5 x 10mm

Security Screw (Qty 4)

M3 x 16mm

Security Screw (Qty 4)

M3 Flat Washer

(Qty 4)

M4 x 12mm

Security Screw (Qty 4)

M5 x 10mm

Security Screw (Qty 3)

M5 x 12mm

Security Screw (Qty 4)

M6 x 12mm Security

Screw (Qty 4)

#14 x 2” Wood Screw

(Qty 2)

¼-20 x 5/16″ Security

Screw (Qty 1)

M5 Security Wrench

(Qty 1)

Barrel Cap

(Qty 4)

M5 x 10mm

Security Screw (Qty 2)

#14 x 2” Wood Screw

(Qty 2)

M5 Flat Washer

(Qty 4)

Sleeve Bushing

Nylon (Qty 4)

Projector Arm

Cover Plate (Qty 1)

Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions

EST100/EST200

Features

The Single-Stud/Dual-Stud Short-Throw Projector Wall Mount (EST100/EST200) is a simple and elegant tool for mounting

a wide variety of short-throw projectors. Its design allows you to use the same mount even if you need to replace the pro-

jector with a different model. Unique features include a mount carriage that easily slides along the projector arm for quick

screen size adjustments, integrated cable management, and Lock-It™ security screws and barrel for enhanced security.

Dual-Stud Back Plate

The EST200 has all the great fea-

tures of the EST100 plus a back plate

designed for mounting on 12” or 16”

dual studs. The back plate also al-

lows lateral shift after installation.

Radial Glide®

Up to 6°of smooth adjustment

in any direction.

Projector Adjustment

Position the projector anywhere along

the projector arm.

Cable Routing

Discreetly manage signal

and power cables through

the projector arm.

Single Stud

Mounts rmly to a

single wood stud.

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5

 Measure distance from center of lens to the top of the mount carriage (C).

® Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended

offset from the projector manual (B). Add the measurement from Step 1 (C), and then add the mounting screw

offset (D) to the total.

(Example: A + B + C + D = ?)

¯ Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated

height measurement starting from the ground up. This height mark will determine your mounting points.

Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the

screen/whiteboard (B).

Lens

Mount Carriage

Projector

In order to determine the installation height and throw distance, the mount carriage must be mounted

to the projector.

Top of Screen

Mark

Legend

A - Distance from ground to the top of the

screen/whiteboard (viewable area).

B - Manufacturers recommended offset

measurement. This measurement will

be listed in the Users Manual.

C - Center of the lens to the top of the

projector bracket.

D - If single-stud EST100, add 5.14˝ to

the calculated total.

If dual-stud EST200, add 1.9” to the

calculated total.

This total distance will be the location for the

lower mounting point.

Proceed to the “Wood Stud Installation”

section.

Ground

Determining the Installation Height

EST100/EST200

Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions

EST100/EST200

THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION.

Use an electronic stud nder (not supplied) to

locate the center of the stud that is in the wall.

Wood Stud

Stud nder

Height

Mark

(from page 5)

Wood Stud

Marking

Projector

Arm

Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal

injury or damage to property.

Wood Stud Installation

Mounting Point

Mark

Step 1

Step 2

Use a pencil to mark the rst mounting point, just

above your height mark (from page 5).

Step 3

 Use the level to make sure the projector arm is level

from side to side.

® Place the projector arm’s second mounting hole over

the rst mounting point mark, then use a pencil to

mark the upper mounting point.

Two (2) mounting points must be used.

Are you installing the single-stud EST100 or the dual-stud EST200?

If EST100, continue to the “EST100 Installation” section below.

If EST200, go to the “EST200 Installation” section on page 8.

EST100 Installation

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7

EST100/EST200

After the pilot holes have been drilled, use

two (2) #14 x 2˝ wood screws to mount the projector

arm to the wooden stud.

Step 5

Once the mounting points have been marked, use a

⅛˝ drill bit and portable drill to drill the pilot holes.

Drill Marking

Step 4

Wood Stud

Marking

Projector

Arm

#14 x 2” Wood Screw

Step 6

Use two (2) M5 x 10mm security screws to attach the

projector arm cover plate to the projector arm.

Wood stud not shown

Go to the “Throw Distance Calculation” section on

page 10.

EST200 Installation

EST100/EST200

Use an electronic stud nder (not supplied) to

locate the center of the stud that is in the wall.

Wood Stud

Stud nder

Height

Mark

(from page 5)

Wood Stud

Marking

Back

Plate

Once the mounting points have been marked, use a

⅛˝ drill bit and portable drill to drill the pilot holes.

Drill Marking

Mounting Point

Mark

Step 1

Step 2

Step 4

Use a pencil to mark the rst mounting point, just

above your height mark (from page 5).

Step 3

 Use the level to make sure the back plate is level from

side to side.

® Align one of the lower mounting slots of the back plate

with the rst mounting point mark and use a pencil to

mark the rest of the mounting points.

Four (4) mounting points must be used. Two (2)

upper mounting points and two (2) lower mounting

points.

Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions

EST100/EST200

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9

Step 5

Put the projector arm cover plate on the projector arm.

Projector Arm

Cover Plate

Step 6

 Place the projector arm assembly within the desired

mounting slots on the back plate.

® Use four (4) M5 x 10mm security screws, four (4)

M5 at washers and four (4) sleeve bushing nylons

to attach the projector arm assembly to the back

plate.

The elongated mounting slots in the back plate

allow some lateral shift for precisely adjusting the

projector arm.

Use four (4) #14 x 2” wood screws to mount the back

plate to the wooden studs where the pilot holes are.

The elongated mounting slots in the back plate allow

some lateral shift for precise adjustments against

the studs.

Proceed to the “Throw Distance Calculation” section

on page 10.

Step 7

Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation

EST100/EST200

Please review the Operator’s Manual that came packaged with your projector before attaching the upper

mounting bracket. The correct throw distance (the distance from the projector to the screen) must be

determined prior to mounting the projector.

 Refer to the projectors User’s Manual to

determine the distance from the lens to

the front of the screen (X).

® Measure the distance from the front of

the lens to the center of the projector (Y).

¯ Measure the distance from the wall to the

face of the whiteboard/screen (Z).

° Add all measurements (X + Y + Z) to

determine projector placement on the

arm assembly. This measurement

will determine where the center of the

mount bracket will be located on the

arm assembly. Please make note of this

measurement.

Front Lens

Rear Lens

Calculations

X = Manufacturers recommended

throw distance

Z = Distance from wall to face of

whiteboard/screen

Front Lens Throw Distance =

(X + Y + Z)

Rear Lens Throw Distance =

(X - Y + Z)

Throw Distance Calculation

The EST100/EST200 can be also used as

a wall-mounted standard projector mount as

well as a short throw projector mount. Align

the projector facing the opposite direction

from the wall plate to project the image

across the room. Please take into account

the projectors throw capabilities prior to

mounting in the projector opposite direction.

Proceed to the “Projector Installation” section.

Projector Installation

Locate the mounting points on the bottom of the projector

(see arrows).

Proceed to the “Attaching the Mount Carriage” section.

Attaching the Projector to the Mount Carriage

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Premier Mounts Support et étagère

Premier Mounts

Premier Mounts AST-2446-2 Manuel utilisateur

Premier Mounts

Premier Mounts SOAD Manuel utilisateur

Premier Mounts

Premier Mounts PTM-B Manuel utilisateur

Premier Mounts

Premier Mounts AM100 Manuel utilisateur

Premier Mounts

Premier Mounts GB-AVSTOR4 Manuel utilisateur

Premier Mounts

Premier Mounts MM-CB3 Manuel utilisateur

Premier Mounts

Premier Mounts PSP-DB Manuel utilisateur

Premier Mounts

Premier Mounts LMVLF Manuel utilisateur

Premier Mounts

Premier Mounts CTM-MS1 Manuel utilisateur

Premier Mounts

Premier Mounts Universal Projector Mount PBC-UMS Manuel utilisateur

Premier Mounts

Premier Mounts Nesting Cart Series Manuel utilisateur

Premier Mounts

Premier Mounts SHLF-EQ Manuel utilisateur

Premier Mounts

Premier Mounts EST200 Manuel utilisateur

Premier Mounts

Premier Mounts UNI-PDS Manuel utilisateur

Premier Mounts

Premier Mounts AM100 Manuel utilisateur

Premier Mounts

Premier Mounts PDS-PLUS Manuel utilisateur

Premier Mounts

Premier Mounts MVWC-3X3 Manuel utilisateur

Premier Mounts

Premier Mounts PSD-TL Manuel utilisateur

Premier Mounts

Premier Mounts LPSA3747 Manuel utilisateur

Premier Mounts

Premier Mounts PBM-760L Manuel utilisateur

Premier Mounts

Premier Mounts RFM Manuel utilisateur

Premier Mounts

Premier Mounts SHLF-VC Manuel utilisateur

Premier Mounts

Premier Mounts MVW463 Manuel utilisateur

Premier Mounts

Premier Mounts AM50 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur