Premier Mounts PSD-TL Manuel utilisateur
INSTALLATION INSTRUCTIONS
PSD-TL
60” / 72” / 84”
Floor Stand
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
Phone: 800-368-9700
Fax: 800-832-4888
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2009
9532-565-001-03
Installation Instructions Page 3
Parts List Congratulations on the purchase of your new Premier Mounts PSD-TL stand. This stand is shipped with all proper
installation hardware and components. Make sure that none of these parts are missing and/or damaged before
beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts
(800) 368-9700.
PSD-TL Base (Qty 1) Support Poles (Qty 2)
Screwdriver
(Not Supplied) 1/2” Socket and Socket
Wrench (Not Supplied)
M10 x 12mm Slotted
Hex Head (Qty 4)
PSD-SPA (Qty 1) M8 x 10mm Set Screw (Qty 10)
The length will vary depending
on the application.
84”
72”
60”
M10 Flat Washers
(Qty 4)
Shelf (Optional)
NOTE: The max weight capacity for
the shelf is 25lbs.
PSD-TL
Installation Tools (not supplied)
5/32” Allen Wrench
Page 4 Installation Instructions
PSD-TL
Features
Congratulations on the purchase of your new Premier Mounts PSD-TL Floor Stand. When combined with a mount, our floor stand
allows you to place a flat-panel in a horizontal or vertical position (with PSM and RTM-L/S mounts only). The flat-panel height
is adjustable to any point along the stand’s vertical support poles to achieve the perfect viewing level. The PSD-TL mates directly to
our CTM, USA, UFA, RTM-L/S or PSM series of mounts.
PSD-TL Base
USA Mount
CTM Series MountRTM-S Mount RTM-L Mount
UFA Mount
PSD-TL Base
PSD-TL Base PSD-TL Base PSD-TL Base
PSM Series Mount
PSD-TL Base
Installation Instructions Page 5
PSD-TL
Support Pole Installation
Remove the stand out of the box and check for all proper hardware, if missing any hardware please call Premier Mounts.
A mount is required to complete the PSD-TL system. Refer to the mount’s installation instructions to install the mounting
bracket.
Step 1. Insert the poles inside the base columns of the
PSD-TL, making sure they are fully seated on
the base with the cable access holes facing the
rear of the base.
Step 2. Secure the support poles by inserting and
tightening the four (4) M8 x 10mm locking set
screws that are located on the back of the
mounting columns.
Step 3. Tighten set screw with the supplied Allen
wrench. Do not over tighten the screws.
Step 1. Install the PSD-SPA (mount adapter) over the top
of the support poles and secure it at the desired
height with the four (4) M8 x 10 set screws
(supplied).
Step 2. Use the Allen wrench (supplied) to secure the
adapter to the support poles.
Adapter Installation
PSD-SPA Adapter
(facing forward)
Allen Wrench
M8 x 10mm
Set Screws
Support Poles
2” Diameter Support Poles
Allen Wrench
Mounting Columns
PSD-TL
Mounting Screws
ThePSD-SPAadapterisusedwiththeCTMand
PSM Series mounts only. The PSD-SPA is not
needed when installing the USA, UFA or
RTM-L/S mounts.
Please see Page 8 for optional shelf installation instructions.
The PSD-SPA must be facing forward when
mounted to the support poles.
Page 6 Installation Instructions
CTM and PSM Series Installation
PSD-TL
This stand is intended for use only with the maximum weights indicated. Use with products heavier than the
maximum weights indicated may result in instability causing possible injury.
The flat-panel is very heavy; two people are required to lift the flat-panel and secure it to the stand.
To install the mounting brackets to the flat-panel, refer to the CTM and PSM installation instructions.
Step 2. Raise the flat-panel with the left and right brackets
secured to the flat-panel and insert the bottom and top hooks
from the mounting arms to the top and bottom rods found
on the CTM back plate.
Step 3. Secure the mounting arms with the two (2) M6 x 12mm
Safety knobs (supplied with the CTM mount).
Step 4. Insert and tighten two (2) M6 x 30mm lateral shift screws
(supplied with the CTM mount) on the bottom of the
mounting arms. These screws will prevent the flat panel
from moving side-to-side.
The safety knobs MUST be used. Failure to
do so may result in damage to the flat-panel or
personal injury.
CTM Back
Plate
Flat-Panel
PSD-TL Base
(facing forward)
CTM Series
Mounting Brackets
M6 x 12mm
Safety Knobs
Step 1. For the CTM-Series, secure the back plate to
the four (4) threaded mounting points found on
the PSD-SPA with the four (4) M10 x 12 bolts
and flat washers (supplied).
The directional arrow must be pointing
up prior to installation. Secure the follow-
ing plates to the secured PSD-SPA on the
support poles.
Installing the CTM
Support Poles
PSD-SPA Adapter
Directional Arrow
CTM Back Plate
M10 x 12mm
Bolts
M10 Flat Washers
PSD-TL Base
(facing forward)
M6 x 30mm Lateral
Shift Screws
Installation Instructions Page 7
PSD-TL
USA, UFA and RTM-L/S Installations
The USA, UFA, RTM-L and RTM-S Series of stand/cart mounts attach to the PSD-TL without the use of the PSD-SPA.
Please follow the installation instructions that are packaged with these mounts.
Step 1. Slide the USA, UFA, RTM-L and RTM-S Series over and onto the support poles.
Step 2. Determine the desired height.
Step 3. Tighten the set screws, located at the rear of each mount, using the supplied Allen wrench.
Step 1. For the PSM-Series, secure the back plate to the four (4)
threaded mounting points found on the PSD-SPA with the
four (4) M10 x 12 bolts and flat washers (supplied).
Installing the PSM Support Poles
PSD-SPA Adapter
Directional Arrow
PSM Back Plate
M10 x 12mm
Bolts
M10 Flat Washers
Step 2. Raise the flat-panel display with the mounting bracket
secured and insert the four (4) tab openings from the PSM
mount to the four (4) receiving tabs found on the back
plate.
Step 3. Push the flat-panel display down, right and down again to
lock the mount together.
Step 4. Make sure all tab openings are interlocked with the
receiving tabs before letting go of the flat-panel.
Step 5. Secure the brackets with two (2) M6 x 12mm Phillips
(supplied with the PSM mount) screws for additional
security.
PSM Back Plate
PSM Mounting
Bracket
Flat-Panel
M6 x 12mm
Screws
PSD-TL Base
(facing forward)
PSD-TL Base
(facing forward)
Page 8 Installation Instructions
PSD-TL
Optional Installations
Floor Installation
Step 1. If securing the base to the floor, use
(commercially available) hardware.
Step 1. The shelf must be attached before the flat-panel
and PSD-SPA adapter is installed to the
stand.
Step 2. Attach the shelf to the poles by sliding the shelf
over the poles and down into position.
Step 3. Determine the final height and secure the shelf
using four (4) M8 x 10mm set screws.
Step 4. Tighten these screws using the supplied Allen
wrench.
Do not install the optional shelf higher than
39”.
If using a shelf, please install prior to
attaching the flat-panel.
Suitable Hardware
(Commercially Available)
Shelf Installation
Optional
Shelf
M8 x 10mm
Set Screws
Allen Wrench
DO NOT load the Stand past the maximum
weight capacity.Failure to comply with this
warning may result in Stand instability
leading to equipment damage or personal
injury.
WARNING
PSD-TL Base
(facing forward)
PSD-TL Base
(not facing forward)
Installation Instructions Page 9
PSD-TL
Technical Specifications
All measurements are in inches(mm).
Table des matières
Autres manuels Premier Mounts Support et étagère
Premier Mounts
Premier Mounts Universal Flat-Only Mount UFM Manuel utilisateur
Premier Mounts
Premier Mounts Convergent UNI-UPS-A CLD Manuel utilisateur
Premier Mounts
Premier Mounts PFC-OMND Manuel utilisateur
Premier Mounts
Premier Mounts PTM Manuel utilisateur
Premier Mounts
Premier Mounts Rotary RTM-S Manuel utilisateur
Premier Mounts
Premier Mounts Nesting Cart Series Manuel utilisateur
Premier Mounts
Premier Mounts ECM-3763S Manuel utilisateur
Premier Mounts
Premier Mounts MM-CP15 Manuel utilisateur
Premier Mounts
Premier Mounts AM100 Manuel utilisateur
Premier Mounts
Premier Mounts iPad IPM-500 Manuel utilisateur
Premier Mounts
Premier Mounts AM175 Manuel utilisateur
Premier Mounts
Premier Mounts PDS-PLUS Manuel utilisateur
Premier Mounts
Premier Mounts PBM-760L Manuel utilisateur
Premier Mounts
Premier Mounts UMB-DBTS Manuel utilisateur
Premier Mounts
Premier Mounts FLIP Manuel utilisateur
Premier Mounts
Premier Mounts CONVERGENT TVF Series Manuel utilisateur
Premier Mounts
Premier Mounts Universal Projector Mount PBC-UMS Manuel utilisateur
Premier Mounts
Premier Mounts AST-2446-2 Manuel utilisateur
Premier Mounts
Premier Mounts LMVF Manuel utilisateur
Premier Mounts
Premier Mounts AM100 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
