PowerWalker VI RT HID Series Manuel utilisateur

ENGLISH

Assembly of VI/VFI RT HID Series

I. Installing the UPS

ENGLISH

II. Connecting the EBM in Tower form:

1. Slide down the UPS and EBM vertically and place two UPS stands with the extend

part at the end of the tower.

2. Tighten the screw on the metal

sheet for stabilization

3. Connect the Earth line from UPS

(port A ) to EBM (port B)

4. Take off the front panel, and connect the battery terminal (A) from UPS to EBM

terminal (B) shown as below. Users need to remove the small gate(C) on side of

the front panel to allow the outlet wire of the EBM to pass through the gate and

then reassemble front panel.

ENGLISH

III. Connecting the EBM in a rack form

1. Using the same method as assembling

UPS in a rack form, assemble EBM into

the rack-mounting on the top or

bottom of the UPS.

2. Connect the earth line from UPS (port

A ) to EBM (port B )

3. Take off the LCD box, and unscrew the

internal screws.

4. Take off the front panel, and connect

the battery terminal (A) from UPS to

EBM terminal (B) shown as below.

Users need to remove the small gate(C)

on side of the front panel to allow the

outlet wire of the EBM to pass through

the gate and then reassemble front

panel.

5. After installing the UPS into rack, the load can then be connected to UPS. Please

Unscrew

ENGLISH

make sure the load equipment is turned off before plugging all loads into the output

receptacle.

IV. Connecting the Multiple EBMs

1000VA/1500VA/2000VA and 3000VA UPS include external battery port that allows users

to connect multiple EBM in order to provide additional backup time. Follow the

procedure to install multiple EBM as below.

V. Connecting multiple EBMs in Tower form

1. Connect Earth line between UPS and the

first EBM, and then connect Earth Line

between the first EBM and the second

EBM.

2. Take off the front panel, and connect the

battery terminal (A) from UPS to EBM

terminal (B) shown as below. And then

connect the battery terminal (D) from the

first EBM to the battery terminal (E) from

the second EBM. Users need to remove

the small gate(C) on side of the front

panel to allow the outlet wire of the EBM

to pass through the gate and then

reassemble front panel.

VI. Connecting the Multiple EBMs in rack form

1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between

the first EBM and the second EBM.

ENGLISH

2. Take off the front panel, and connect the battery terminal (A) from UPS to EBM terminal

(B) shown as below. And then connect the battery terminal (D) from the first EBM to the

battery terminal (E) from the second EBM. Users need to remove the small gate(C) on side

of the front panel to allow the outlet wire of the EBM to pass through the gate and then

reassemble front panel.

Note: Three or more EBMs can be connected to the UPS in the same way as shown above.

VII. Replacing UPS Internal Batteries

Follow the steps and Charts as below to replace batteries:

1. Take off the LCD box, and remove the

screws.

2. Slide and Pull the front panel leftward

and then take it off.

ENGLISH

3. Disconnect the cable from the UPS and

battery pack.

4. Remove the right inner battery bracket.

5. Pull the battery pack out onto flat area.

6. Install new battery pack into UPS.

7. Screw up the battery bracket and

reconnect the battery cable A and B

8. Re-install the front panel back to UPS.

Ce manuel convient aux modèles suivants

Autres manuels PowerWalker UPS

PowerWalker

PowerWalker VFD 400 Manuel utilisateur

PowerWalker

PowerWalker VFI ICT IoT Series Manuel utilisateur

PowerWalker

PowerWalker VI CW Series Manuel utilisateur

PowerWalker

PowerWalker VFI 1000CRM LCD Manuel utilisateur

PowerWalker

PowerWalker BP P96T Guide de l'administrateur

PowerWalker

PowerWalker VFI 2000 CRM Manuel utilisateur

PowerWalker

PowerWalker VFI 6000 CG PF1 Manuel d'installation et d'exploitation

PowerWalker

PowerWalker VFI CPG PF1 3/3 Series Manuel utilisateur

PowerWalker

PowerWalker VFI 6000 ICT Manuel utilisateur

PowerWalker

PowerWalker VFI 10-200K CPT 3/3 Manuel utilisateur

PowerWalker

PowerWalker VFI RT HID Series Manuel utilisateur

PowerWalker

PowerWalker VFI 1000R LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 1000RM Manuel utilisateur

PowerWalker

PowerWalker 650 SH Manuel utilisateur

PowerWalker

PowerWalker VI TW Series Manuel utilisateur

PowerWalker

PowerWalker VFI 1000 CRM Manuel utilisateur

PowerWalker

PowerWalker 1000VA Manuel utilisateur

PowerWalker

PowerWalker VFI 1000R/1U Manuel utilisateur

PowerWalker

PowerWalker VI 1200 Manuel utilisateur

PowerWalker

PowerWalker VFI 10K ICT IoT 3/3 BI Manuel utilisateur

PowerWalker

PowerWalker VI 1000RT LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 6000 TGB Manuel utilisateur

PowerWalker

PowerWalker VFI 6000 CT LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 20000-40000TAP 3/3 BI Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur