PowerWalker VI 650 SH Manuel utilisateur

Line Interactive UPS

PowerWalker VI 650 SH

PowerWalker VI 850 SH

PowerWalker VI 1200 SH

PowerWalker VI 2200 SH

(Schuko / French / IEC)

PowerWalker VI 650 SHL

PowerWalker VI 850 SHL

PowerWalker VI 1200 SHL

PowerWalker VI 2200 SHL

(Schuko / French / IEC)

Quick Start Guide

EN/DE/PL/FR/PT/RU/CZ

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per PowerWalker UPS VI SHL

650VA o cerca il tuo prodotto tra le migliori offerte di Gruppi di Continuità

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS – This manual contains important instructions for PowerWalker VI

650/850/1200/2200 SH and VI 650/850/1200/2200 SHL series that should be followed during installation

and maintenance of the UPS and batteries.

This product is specially designed for PCs and it is not recommended for use in any medical

equipment, life-supporting system and other specific important equipment.

Do not plug household appliances such as hair dryers, microwave ovens or vacuum cleaners to UPS.

Do not attach a power strip or surge suppressor to the UPS.

Do not plug the UPS into its own output.

Connection to any other type of receptable other than two-pole, three-wire grounded receptacle

may result in shock hazard as well as violate local electrical codes.

To reduce risk of overheating the UPS, do not cover the UPS´ cooling vents.

This unit intended for installation in a controlled environment (temperature controlled, indoor area

free of conductive contaminants). Avoid installing the UPS in locations where there is standing or

running water or excessive humidity and do not use it in any of the following environments:

oAny area with combustible gas, corrosive substance or heavy dust.

oAny area with extraordinarily high or low temperature (above 40˚C or below 0˚C) and

humidity of more than 90%.

oAny area exposed to direct sunshine or near any heating apparatus.

oAny area with serious vibrations.

oOutdoor.

The utility power outlet shall be near the equipment and easily accessible. In the event of an

emergency, press OFF button and disconnect the power cord from the AC power supply to properly

disable the UPS.

The internal short circuiting of the UPS will lead to dangers such as electric shock or fire; therefore

do not allow liquids or any foreign object to enter the UPS. No water containers (such as a water

glass) or any other liquid-containing vessels shall be placed on the top of the UPS so as to avoid such

dangers as electric shock.

Please do not use the UPS in excess of the rated load capacity.

Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

Risk of electric shock, do not attempt to disassemble the unit. No user serviceable parts inside. Refer

servicing to qualified service personnel.

If UPS is to be stored for a long time, it is recommended to recharge the batteries (by connecting the

utility power to UPS, switch “ON”), once a month for 24 hours to avoid a full battery discharge.

In case smoke is found coming out from the device, please cut off the power supply quickly and

contact the distributor.

The UPS contains one/two large-capacity batteries. So the shell shall not be opened, otherwise such

dangers as electric shock will be caused. If any internal overhaul or replacement of the battery is

required, please contact the distributor.

Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries

and the required precautions. Keep unauthorized personnel away from batteries.

A battery can present a risk of electrical shock and high short circuit current. The following

precautions should be observed when working on batteries:

oRemove watches, rings, or other metal objects from the hand.

oUse tools with insulated handles and wear rubber gloves and boots.

oDo not lay tools or metal parts on top of batteries.

oDisconnect charging source prior connecting or disconnecting batteries terminals.

When replacing batteries, replace with the same type and number of the sealed lead-acid batteries.

The maximum ambient temperature rating is 40°C.

Do not dispose of battery or batteries in a fire. The battery may explode.

Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and

eyes. It may be toxic.

Icon Φ on the rating label stands for phase symbol.

This pluggable type A equipment with battery already installed by the supplier is operator installable

and may be operated by laymen.

During the installation of this equipment it should be assured that the sum of the leakage currents

of the UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains,

hazardous voltage still may be accessible through supply from battery. The battery supply should be

therefore disconnected in the plus and minus pole of the battery when maintenance or service work

inside the UPS is necessary.

In the event that there is fire occurring in the vicinity, please use dry-power extinguishers. The use of

liquid extinguishers may give rise to the danger of electric shock.

This product complies with the safety and environmental regulations in EU.

If the time arises to throw away your product, please recycle all the components possible. Batteries and

rechargeable batteries are not to be disposed in your domestic waste! Please recycle them at your local

recycling point. Together we can help to protect the environment.

1. Introduction

PowerWalker VI SH and VI SHL series are intelligent and compact line interactive UPSs (Uninterruptable Power

Supplies) which are designed to protect your personal computer or sensitive electronic equipments from all

forms of power interference, including complete power failures. It is equipped with many features that allow

any attached equipment to operate longer and more reliability.

2. Description of Features

Easy to use and install utilized microprocessor control to maximize the reliability and efficiency

Equipped with built-in boost and buck AVR function

HID support – default O/S drivers can support basic functionality without PowerWalker software

DC Cold start function

Auto restart while AC recovery.

Provides AC Overload protection

Short recharging time

RJ11/RJ45 (in/out) LAN/Modem/Phone line protection

3. Package Contents

You should have received the following items inside of package:

UPS Unit

USB Cable

AC Input Power Cord

(does not apply for VI 650/850

SH/SHL FR and Schuko, which

have fixed input cable)

Software CD

User Manual

IEC cable

(only for IEC outlet models)

4. Product Overview

4.1. PowerWalker VI 650/850/1200/2200 SH FR/IEC/Schuko

Front Panel:

VI 650/850 SH

VI 1200/2200 SH



USB port

LED Indicators

AC mode: green lightning

Battery mode: green flashing

 Power ON/OFF



Power ON/OFF

LED Indicators

Normal: green lightning

Battery mode: yellow flashing

AC mode: green lightning

Fault mode: red lightning

4.2. PowerWalker VI 650/850/1200/2200 SHL FR/IEC/Schuko

Front Panel

VI 650/850 SHL VI 1200/2200 SHL

4.3. Display for PowerWalker VI SHL series

When LCD starts to work, it will display all information

for 3 seconds.

When in normal mode, it will display as below.

When in AVR mode, it will display as below. And the

mark will flicker every 1second.

When in battery mode, it will display as below. And

the mark will flicker every 1second.

Note: If I/P-V<40V，input voltage will display “000”

When in off charging mode, it will display as below.

Note: the output voltage always is displayed as “000”

in off charging mode.

When in fault mode, it will display as below. “FAULT”

character and “0” character only.

1. Load level definition:

Load level

Load bar Indication

0%~25%

25%~50%

50%~75%

75%~100%

2. Battery capacity definition:

Battery level

Battery level < 20%

20% ≤ Battery level < 40%

40% ≤ Battery level < 60%

60% ≤ Battery level < 80%

80% ≤ Battery level

3. When over load, the mark will flicker every 1second.

4. When battery low, the mark will flicker every 1second.

4.4. Back Panel for PowerWalker VI SH and SHL series

650/850 IEC

1200 IEC 2200 IEC

650/850 Schuko

650/850 FR

1200/2200 Schuko 1200/2200 French



AC input

RJ11 Modem/phone line

Protection

4*IEC outlet or 2* Schuko

outlet or 2*French outlet

AC input

6*IEC outlet or 2* IEC & 2* Schuko outlet or 2* IEC &

2*French outlet

USB port

RJ45 LAN/Modem/phone line protection

❺Breaker

5. Installation and Initial Startup

Before installation, please inspect the unit. Be sure that nothing is damaged.

I: Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow around the unit,

and is free from excessive dust, corrosive fumes and conductive contaminants. Please place the UPS away

from other units at least 20 cm to avoid interference. Do NOT operate the UPS where the temperature

exceeds 0-40° C and the humidity is over 0-90 % RH.

II: Connect to Utility and Charge

Plug in the AC input cord to the 2-pole, 3-wire grounded wall outlet. For the best results, we suggest charging

the battery at least 6 hours with no load (no electrical devices such as computers, monitors, rtc.) connected

before initial use. The unit charges its battery while connecting to the utility.

III: Connect the Loads

Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS

unit, and devices connected to the UPS will be protected by UPS unit.

IV: Connect LAN cable, Modem or Phone line for Surge Protection

Connect for example a single modem or phone line into surge-protected “IN” outlet on the back panel of the

UPS unit. Connect from “OUT” outlet to the computer with another phone line cable.

V: Connect USB Cable

To monitor the UPS status, such as unattended UPS shutdown and start-up, by using bundled software,

please connect the UPS and PC with USB cable included.

VI: Turn On/Off the Unit

Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again the power switch.

Do not attach a power strip or surge suppressor to the UPS.

NEVER connect a laser printer or scanner to the

UPS unit, because in-rush current generated by

motor’s devices may cause the damage of the unit.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels PowerWalker UPS

PowerWalker

PowerWalker VI 650SE LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 1000CRM LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 6000 AT Manuel utilisateur

PowerWalker

PowerWalker PF 1 6K Manuel utilisateur

PowerWalker

PowerWalker VFI 10000CRM LCD Manuel utilisateur

PowerWalker

PowerWalker VI 1000RT LCD Manuel utilisateur

PowerWalker

PowerWalker VFD 400 Manuel utilisateur

PowerWalker

PowerWalker VI 750 PSW Manuel utilisateur

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manuel utilisateur

PowerWalker

PowerWalker VFI 1000RM LCD Manuel utilisateur

PowerWalker

PowerWalker VI TW Series Manuel utilisateur

PowerWalker

PowerWalker 650 SH Manuel utilisateur

PowerWalker

PowerWalker VI 500 R1U Manuel utilisateur

PowerWalker

PowerWalker VFI 1000RT LCD Manuel utilisateur

PowerWalker

PowerWalker VFI CPG PF1 3/3 Series Manuel utilisateur

PowerWalker

PowerWalker VFI 160K CPG 3/3 BX Manuel utilisateur

PowerWalker

PowerWalker VFD 400 IEC Manuel utilisateur

PowerWalker

PowerWalker VFI 1000 C LCD Manuel utilisateur

PowerWalker

PowerWalker VFI 10K CPH Manuel utilisateur

PowerWalker

PowerWalker VFI 1000 Manuel utilisateur

PowerWalker

PowerWalker VI 400 Manuel utilisateur

PowerWalker

PowerWalker VI 400 SE Manuel utilisateur

PowerWalker

PowerWalker VI 2000 LCD Manuel utilisateur

PowerWalker

PowerWalker VI CW Series Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur