PEERLESS SA761PU Mode d’emploi

Models: SA761PU, SA763PU

Installation and Assembly:

Universal Articulating Arm Wall Mount for 37" to 63" Flat Panel

Screens

USC

SA761PU SA763PU

Model Maximum Load Capacity Screen Size Range

SA761PU 130 lbs (59 kg) 37" - 60"

SA763PU 200 lbs (90.7 kg) 37" - 63"

3215 W. North Ave. • Melrose Park, IL • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

2 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.............................................................................................................................................................................3, 4

Wall installation...................................................................................................................................................................6, 7

Installing Adapter Brackets to Screen...............................................................................................................................8 -12

Mounting Flat Panel Screen .................................................................................................................................................13

Cable Management ..............................................................................................................................................................16

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 3/16" (5 mm) drill bit for wood studs, 5/16" (10 mm) drill bit for concrete

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Contact Qualiﬁed Professional (not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

SA761PU SA763PU

Description Qty. Part # Part #

wall arm assembly 1 095-P1643 095-P1645

Buniversal adapter bracket 1 095-P1635-2 095-P1635-2

Cwood screws 4 520-1243 520-1243

Dconcrete anchors 4 590-0321 590-0321

EM10 x 15 mm socket head screw 2520-9262 520-9262

Fwall plate cover 2590-1325 590-1325

Gcable ties 8590-1168 -

16 - 590-1168

H6 mm allen wrench 1 560-9716 560-9716

I5 mm allen wrench 1 560-9640 560-9640

Jrear cable cover 2 590-P1326 -

4-590-P1326

Kfront cable cover 2 590-P1327 -

4-590-P1327

Parts List

SA761PU SA763PU

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

4 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Adapter Bracket Fasteners

M4 x 12 mm (6)

(504-9013)

M4 x 25 mm (4)

(504-1015)

M5 x 12 mm (4)

(520-1027) M5 x 25 mm (4)

(520-9543)

M8 x 16 mm (6)

(520-9257)

M8 x 40 mm (4)

(520-1136)

M8 x 25 mm (4)

(520-1031)

I.D. .34" (4)

(540-1059)

I.D. .22" (4)

(540-1057)

M6 x 30 mm (4)

(510-9109)

M6 x 12 mm (4)

(520-1128) M6 x 25 mm (4)

(520-1208)

M6 x 20 mm (4)

(520-9402)

multi-washer (6)

(580-1036)

5 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

1/4-20 X 17 MM SCREWS WALL PLATE

WALL ARM

SLIDE PLATE

WALL PLATE RAIL

NOTE: If mounting wall arm (A) to wood stud walls, slots on wall plate must align to wood studs.

Determine desired location of screen center detailed in step 2.

Measure the distance from the center of wall arm (A) to desired screen center. Loosen four 1/4-20 x 17 mm screws

using 5 mm allen wrench (I). Slide wall arm assembly 4-1/2" to the left or right as shown in ﬁgure 1.1. NOTE: Align

bevels (dots) of slide plate with bevels (dots) of wall plate rails as shown in detail 1 then retighten 1/4-20 x 17 mm

screws.

Do not adjust arm while screen is attached.

Skip to page 6 for Wood Stud Installation.

Skip to page 7 for Concrete and Cinder Block Installation.

Optional Horizontal Adjustment of Wall Arm on Wall Plate

ﬁg. 1.1

DETAIL 1

6 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Use a stud ﬁnder to locate the edges of the studs and draw a vertical line down the center of each stud. Determine

and mark the desired screen center on the wall. Place wall plate template (wall arm) on wall with top mounting slots

9" (229 mm) above desired screen center as shown in ﬁgure 2.1. Level wall plate template (wall arm) on wall and

mark center of four mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 3/16"

(5 mm) dia. pilot holes to a depth of 3" (76 mm). Attach wall arm (A) to wall using four wood screws (C) as shown in

ﬁg. 2.2.

Level wall plate then tighten all fasteners.

Installation to Double-Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

WOOD STUD

ﬁg. 2.2

(229 mm)

WOOD STUD

CS = CENTER OF SCREEN

ﬁg. 2.1

7 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Installation to Solid Concrete or Cinder Block

Determine and mark the desired screen center on

the wall. Place wall plate template (wall arm) on wall

with top mounting slots 9" (229 mm) above desired

screen center as shown in ﬁgure 2.1. Level wall plate

template (wall arm) on wall and mark center of four

mounting holes making sure that the mounting holes.

Drill four 13/32" (10 mm) dia. pilot holes to a depth of

3" (76 mm). Insert anchors (D) into holes ﬂush with

wall as shown (right). Place wall arm over anchors and

secure with 5/16 x 3" screws (C). Level, then tighten all

fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied

by installer (not evaluated by UL).

WARNING

SOLID CONCRETE

CINDER BLOCK

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

8 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

NOTE: If screen has a VESA 400 horizontal

mounting pattern, skip to step 3-3 or 3-4 on page

10.

NOTE: For VESA 200x200 or VESA 200x100

mount hole patterns, skip to step 4 on page 11.

NOTE: For dedicated PLP plate installation skip to

step 5 on page 13.

Remove four 1/4-20 x .6" screws using 5 mm allen

wrench (I) and loosen two 1/4-20 x 1.25" screws

1/2 turn to allow for screen bracket adjustment.

1/4-20 x .6" SCREWS

1/4-20 x 1.25" SCREWS

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen.

Place screen face side down and refer to screen manufacturers instructions for removing obstructions from the

back of the screen. Adjust screen brackets to align with screen mounting holes.

Measure horizontal mounting hole pattern and choose ﬁxed stop-position from chart below.

3-1

FIXED STOP-POSTION #2

FIXED STOP-POSTION #1

FIXED STOP-POSTION #3

horizontal mounting hole pattern fixed stop-position

10-3/4" - 16-1/16" (273 - 408 mm) #1

15-1/16" - 21-9/16" (383 - 548 mm) #2

20-7/16" - 27-9/16" (519 - 700 mm) #3

Installing Adapter Brackets to Screen

9 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Select the screws from the bafﬂed fastener pack that best ﬁt your screen and secure to screen following step 3-3

or 3-4 on page 10.

NOTE: Top and bottom mounting holes must be used for attaching screen brackets. Middle holes should also be

used where the fasteners and screens allow.

Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.

CENTER SCREEN BRACKETS VERTICALLY AND

HORIZONTALLY ON BACK OF SCREEN

SCREEN

SCREEN BRACKETS

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

• Tighten screws so screen brackets are ﬁrmly attached to screen. Do not tighten with excessive force. Overtightening

can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to

become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

Installing Adapter Brackets to Screen

3-2

10 of 66 ISSUED: 10-30-09 SHEET #: 095-9298-7 01-15-11

Begin with the shortest length screw, hand thread

screw through multi-washer and screen brackets

(B) into screen as shown below. Screw must make

at least three full turns into the mounting hole and

ﬁt snug into place. Do not over tighten. If screw

cannot make three full turns into the screen, select

a longer length screw from the bafﬂed fastener

pack. Repeat for remaining mounting holes, level

screen brackets and tighten screws.

NOTE: Spacers may not be used, depending upon

the type of screen.

Skip to step 3-5.

Begin with the longest length screw, hand thread

screw through multi-washer, screen brackets (B)

and spacer in that order into screen as shown

below. Screw must make at least three full turns

into the mounting hole and ﬁt snug into place.

Do not over tighten. If screw cannot make three

full turns into the screen, select a shorter length

screw from the bafﬂed fastener pack. Repeat for

remaining mounting holes, level screen brackets

and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

3-3

3-4

SCREEN

MULTI-WASHER

SCREW

SCREEN

MULTI-WASHER

SPACER

SCREW

Center screen brackets horizontally and vertically

on back of screen. Tighten two 1/4-20 x 1.25"

screws. Reinstall four 1/4-20 x .6" screws using

5 mm allen wrench (I) into appropriate ﬁxed-stop

position from chart on page 8.

3-5 1/4-20 x 1.25" SCREWS

1/4-20 x .6" SCREWS

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels PEERLESS Support et étagère

PEERLESS

PEERLESS HCW201 Manuel utilisateur

PEERLESS

PEERLESS LWB375 Mode d’emploi

PEERLESS

PEERLESS SmartMount D-FPF-320 Mode d’emploi

PEERLESS

PEERLESS VPM 25-W Mode d’emploi

PEERLESS

PEERLESS DS-VW660 and assembly Mode d’emploi

PEERLESS

PEERLESS WWSP 420 Manuel utilisateur

PEERLESS

PEERLESS Smartmount ST670 Mode d’emploi

PEERLESS

PEERLESS PWMT300 Manuel utilisateur

PEERLESS

PEERLESS Paramount PSP2 Mode d’emploi

PEERLESS

PEERLESS IBA1 Mode d’emploi

PEERLESS

PEERLESS PLC Mode d’emploi

PEERLESS

PEERLESS PED 410 Mode d’emploi

PEERLESS

PEERLESS DS-VW760 and assembly Mode d’emploi

PEERLESS

PEERLESS Solid-Point PLCM UN1 Mode d’emploi

PEERLESS

PEERLESS A100IWBMOUNT Mode d’emploi

PEERLESS

PEERLESS LCC 18 Mode d’emploi

PEERLESS

PEERLESS SmartMount SP740P Mode d’emploi

PEERLESS

PEERLESS LCT Series Mode d’emploi

PEERLESS

PEERLESS AEC0609 Mode d’emploi

PEERLESS

PEERLESS LCC 18-C Mode d’emploi

PEERLESS

PEERLESS SmartMount SF650 Mode d’emploi

PEERLESS

PEERLESS Paramount PPF Mode d’emploi

PEERLESS

PEERLESS RTLA-100 Mode d’emploi

PEERLESS

PEERLESS SOLID-POINT PLCM1CP Mode d’emploi

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur