Peerless-AV SUA765PU Mode d’emploi

Installation and Assembly:

Peerless Ultra-Thin Articulating Mount for 50" to 75"*

Flat Panel Displays

Models: SUA765PU

*Display Compatibility Requirements

• Depth of display must be less than 2"

• The depth of this mount (1.24") may not provide

sufﬁcient space for proper ventilation on some displays.

Please refer to the manufacturer's requirements for

mounting your display before installation.

• The display must have a ﬂat mounting surface, or the

mounting holes need to be on the furthest back surface

of the display.

• Input/Output connection must be properly oriented to

accommodate mounting 1.24" from the wall.

ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Max Load Capacity: 100 lb (45.4 kg)

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

2 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

NOTE: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This mount is designed to attach the display 1.24" from the wall. Please refer to manufacturer's installation guide

recommendations for required distance from wall to avoid risk of injury or property damage.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

WARNING

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 5/16" (8mm) bit for concrete and cinder block wall

• 5/32" (4mm) bit for wood stud wall

• level

Table of Contents

Parts List.................................................................................................................................................................................3

Wall installation...................................................................................................................................................................4, 5

Installing Adapter Brackets to Display ....................................................................................................................................6

Mounting Flat Panel Display...................................................................................................................................................8

3 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

CDEFH

Adapter Bracket Fasteners

Parts List Part #Description Qty

Awall arm 1 046-P1323

Badapter bracket 2 046-P1225

Cwood screw 4 500-1090

Dconcrete anchor 4 590-0320

EM4 x 6mm 2 520-1006

Fallen bit 1 560-1133

G4mm allen wrench 1 560-9646

Hscrew cap 8 046-0096

Icable clip 1 046-P1137

Jcable tie 2 046-0136

M8 x 25mm (4)

(560-1737)

M8 x 16mm (4)

(560-1264)

M6 x 12mm (4)

(560-1734)

.75" spacer (8)

(600-1215)

.04" washer (4)

(540-9478)

M6 x 25mm (4)

(560-1735)

M8 x 12mm (4)

(560-1736)

4 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Installation to Wood Stud Wall

Use a stud ﬁnder to locate the edges of the studs. Use of an edge-to-edge stud ﬁnder is highly recommended.

Based on their edges, draw a vertical line down each stud’s center. Center of display mounting plate will be 9.26"

offset from center of outer mounting slot as shown in ﬁgure 1.1 or will be 6.94" offset from center of inner mounting

slot as shown in ﬁgure 1.2. Place wall arm (A) on wall as template, level, and mark the center of four mounting

holes. Top mounting slot will be 6.60" (168mm) above display mounting plate as shown in ﬁgure 1.1.

Drill four 5/32" dia. holes to a minimum depth of 2.5". Secure wall arm (A) to wall with four wood screws (C) as

shown in ﬁgure 1.2. NOTE: Be sure arrow is pointing up when mounting wall arm (A) to wall as shown in ﬁgure 1.1.

Level, then tighten all fasteners.

Insert eight fastener caps (H) into wall plate mounting holes.

ﬁg. 1.1

ﬁg. 1.2

6.60"

(168mm)

9.26"

(235mm)

6.94"

(176mm)

= CENTER OF DISPLAY

DISPLAY

MOUNTING PLATE

• When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that the

wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

WARNING

5 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Installation to Solid Concrete or Cinder Block

NOTE: Wall arm assembly (A) must be mounted to

wall using inner mounting holes.

Make sure that wall arm assembly is level and use

wall plate as a template to mark four mounting

holes. The top mounting slots should be located

6.60" (168mm) above the desired display center as

shown in ﬁgure 1.1 on page 4. Drill four 5/16" (8mm)

dia. holes to a minimum depth of 2.5" (64mm).

Insert anchors (D) in holes ﬂush with wall as

shown. Place wall arm assembly over anchors and

secure with wood screws (C). Level, then tighten

all fasteners. Insert eight fastener caps (H) into

mounting holes. NOTE: Be sure arrow is pointing

up when mounting wall arm assembly (A) to wall as

shown in ﬁgure 1.1.

SOLID CONCRETE CINDER BLOCK

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

• When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum

compressive strength of 2000 psi.

• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90 speciﬁcations

and have a minimum nominal width of 8".

• Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the

side of the block. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Never attach concrete expansion anchors to concrete or cinder block covered with plaster, drywall or other ﬁnishing

material.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

WARNING

6 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

• Tighten screws so display brackets are ﬁrmly attached to display. Do not tighten with excessive force.

Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing

screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

Installing Adapter Brackets to Display

To prevent scratching the display, set a cloth on a ﬂat, level surface that will support the weight of the display. Place

display face side down. If display has obstructions on the back, remove them to allow the adapter brackets to be

attached. Place adapter brackets (B) on back of display, align to holes, and center vertically on back of display as

shown below. Attach the adapter brackets to the back of the display using the appropriate combination of screws,

washers, and spacers as shown in steps 2-1 or 2-2.

NOTE: Top and bottom holes must always be used.

Verify that all holes are properly aligned, and then tighten screws using allen wrench (G).

CENTER

BRACKETS

VERTICALLY

ON BACK OF

DISPLAY

NOTE: "X" dimensions should be equal.

NOTE: For ﬂat back displays proceed to step 2-1. For bump-out or recessed back display skip to step 2-2.

NOTE: LATCH

INDICATES

BOTTOM OF

BRACKETS (B)

WARNING

7 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

For Flat Back Display

For Bump-out or Recessed Back Display

2-2

Begin with the shortest length screw, hand thread through washer, tilt bracket and spacer (where required for

ventilation) into display as shown below. If screw cannot make three full turns into the display and ﬁt snug into

place, select a longer length screw from the bafﬂed fastener pack. Repeat for remaining mounting holes, level

brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of display.

NOTE: If display manufacturer's requirements state that more than 1.2" of ventilation is required, spacers may be

used to add an additional 0.75" of space between the wall and the display as shown below.

Begin with the shortest length screw, hand thread through washer, tilt bracket and spacer in that order into display

as shown below. If screw cannot make three full turns into the display and ﬁt snug into place, select a longer

length screw from the bafﬂed fastener pack. Repeat for remaining mounting holes, level brackets and tighten

screws.

WASHER

ADAPTER BRACKET (B)

DISPLAY

SCREW

DISPLAY

SCREW

ADAPTER BRACKET (B)

SPACER

WASHER

If you have any questions, please call Peerless customer care at 1-800-865-2112.

DISPLAY

SCREW

ADAPTER BRACKET (B)

SPACER

WASHER

2-1

8 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Wall arm assembly (A) must be in closed position to

hang display.

Rotate safety latch with ﬂathead screwdriver into

unlocked position as shown in detail 1.

Hook adapter brackets (B) onto the center of wall arm

assembly (A) adapter plate as shown in ﬁgure 3.1.

Mounting and Removing Flat Panel Display

• Always use an assistant or mechanical lifting equipment to safely lift and position the ﬂat panel displays.

• Be careful not to pinch ﬁngers when opening and closing mount from the wall.

• DO NOT operate or tilt arm assembly when safety latches are in unlocked position. Product may fail and may cause

injury or damage to display.

• Do not tighten safety/security screw (E) with excessive force. Overtightening can cause screw head to become

damaged making it difﬁcult to remove. Tighten screws to 15 in•lb (1.7 N.M.) maximum torque.

WARNING

SAFETY LATCH

DETAIL 1

ﬁg. 3.1

SAFETY

LATCH

DETAIL 2

DETAIL 3

Rotate safety latch with ﬂathead screwdriver. Install

safety/security screw (E) through safety latch into

adapter bracket with phillips screwdriver to lock

down as shown in detail 2 and 3.

9 of 29 ISSUED: 05-01-11 SHEET #: 095-9358-7 11-21-14

Cable Management

Cables may be routed using cable clip (I).

Slip cable clip (I) onto bottom of center joint as shown in ﬁgure 5.1 and secure cables to cable clip using cable tie

(J) as shown in ﬁgure 5.2.

Secure cables to bottom of wall plate using cable tie (J) as shown below.

ﬁg. 5.1 ﬁg. 5.2

CENTER

JOINT J

CABLES

WALL PLATE

SLOTS

All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

2300 White Oak Circle

Aurora, Il 60502

www.peerless-av.com

Instalación y ensamblaje:

Soporte Articulador Peerless Ultra-Delgado Para Pantallas

Planas de 50" a 75"*

Modelos: SUA765PU

Máxima capacidad de carga para: 100 lb (45.4 kg)

PUBLICADO: 05-01-11 HOJA #: 095-9358-6 06-04-14

* Requisitos para la compatibilidad de las pantallas

• La profundidad de la pantalla tiene que ser menos de 2".

• Es posible que la profundidad del soporte (1.24") no

proporcione suﬁciente espacio para la ventilación

adecuada de algunas pantallas. Por favor, repase los

requisitos del fabricante en relación con la instalación de

la pantalla antes de proceder.

• La pantalla tiene que tener una superﬁcie plana para la

instalación o tiene que tener los agujeros de montaje en

la superﬁcie trasera más alejada de la pantalla.

• La conexión de entrada / salida tiene que tener la

orientación adecuada para acomodar una instalación a

1.24" de la pared.

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Table des matières

Langues :

Autres manuels peerless-AV Support TV

peerless-AV

peerless-AV Tru Vue TRP740 Manuel utilisateur

peerless-AV

peerless-AV Neptune Shade Series Manuel utilisateur

peerless-AV

peerless-AV DS-MBZ647P Manuel utilisateur

peerless-AV

peerless-AV SUF661 Mode d’emploi

peerless-AV

peerless-AV PTL635 Manuel utilisateur

peerless-AV

peerless-AV ST650P-M Manuel utilisateur

peerless-AV

peerless-AV Designer Series Manuel utilisateur

peerless-AV

peerless-AV SS560DPB Mode d’emploi

peerless-AV

peerless-AV PRG3-EXA Manuel utilisateur

peerless-AV

peerless-AV PLP-UNM Mode d’emploi

peerless-AV

peerless-AV PLA60-UNL Mode d’emploi

peerless-AV

peerless-AV DS-VWM770 Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT ST680-S Manuel utilisateur

peerless-AV

peerless-AV LCZ-4F4G30B Mode d’emploi

peerless-AV

peerless-AV SmartMount SA771PU Manuel utilisateur

peerless-AV

peerless-AV DS-S560-B2X2 Manuel utilisateur

peerless-AV

peerless-AV ACCXT200 Mode d’emploi

peerless-AV

peerless-AV ACC450 Mode d’emploi

peerless-AV

peerless-AV KIP740 Manuel utilisateur

peerless-AV

peerless-AV DS-S555-4X3 Manuel utilisateur

peerless-AV

peerless-AV SmartMount ST632P Mode d’emploi

peerless-AV

peerless-AV DS-S555-3X2 Manuel utilisateur

peerless-AV

peerless-AV SC560DPB Mode d’emploi

peerless-AV

peerless-AV ACC953 Mode d’emploi

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

peerless-AV SUA765PU Mode d’emploi

Manuels Support TV populaires d'autres marques