Peerless-AV PLAV70 Mode d’emploi

ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Models: PLAV70

Installation and Assembly - Universal Articulating

Swivel Double-Arm for 42" - 95" Plasma Screens

Max UL Load Capacity: 200 lb (91 kg)

2 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• drill

• 7/32" drill bit for wood studs

• 3/8" masonry drill bit for concrete

• 7/16" socket wrench with extension (recommended)

• level

• phillips screwdriver

• 3/4" open-end wrench

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724)

(Metal Stud not evaluated by UL)

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................4

Installation to Solid Concrete or Cinder Block........................................................................................................................5

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Some parts may appear slightly different than illustrated.

DEF

NOPT

MR S

Parts List Part #Description Qty

Awall plate 1 201-1040

Btilt-roll assembly 1 201-1042

Carm assembly 1 201-1044

Dwall support arm axle 2 201-1041

Evinyl trim 3 600-1012

FM10 x 1.5 x 15mm screw 8 520-9262

G.062" nylon washer 1 540-1074

Htilt adjustment knob 1 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315

J.062" delrin washer 4 540-1070

K#8-32 x .375" socket head screw 2 520-1210

Lplastic ﬁnishing cap 6 590-1123

Mholding pin 2 580-1166

Nretainer plug 2 590-1007

O5/16 x 3" wood screw 8 520-1243

P.068" metal washer 8 540-1063

Q9/64" allen wrench 1 560-9728

Rcable management clips 8 590-1166

Scable tie 8 590-1168

T36" polyester mesh sleeve 2 600-1015

U6mm allen wrench 1 560-9716

V10mm concrete anchor 8 590-0321

4 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud ﬁnder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .43" below the

desired screen center. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it

using eight 5/16 x 3" wood screws (O) and washers (P).

Skip to step 2 on page 6.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Never mount this product to metal studs.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations.

• Never exceed the Maximum UL Load Capacity of 200 lb (91 kg).

WARNING

Installation to Wood Stud Wall

5 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Use wall plate (A), making sure that it is level, as

a template to mark holes. The top mounting slots

should be located .43" below the desired screen

center. Use the masonry bit to drill 3/8" (10mm)

dia. holes to a minimum depth of 3" (76 mm). Insert

anchors (V) in holes ﬂush with wall as shown (right).

Place wall plate (A) over anchors (V) and secure

with 5/16 x 3" wood screws (O) and washers (P).

Installation to Solid Concrete or Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten wood screws so that wall plate is ﬁrmly

attached, but do not overtighten. Overtightening

can damage screws, greatly reducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to con-

crete covered with plaster, drywall, or other ﬁnishing

material. If mounting to concrete surfaces covered

with a ﬁnishing surface is unavoidable (not evaluated

by UL), the ﬁnishing surface must be counterbored

as shown below. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer

(not evaluated by UL).

WARNING

Drill holes and insert anchors (V).

Place plate (A) over anchors (V) and secure with screws (Q).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

6 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

To route cables through cord management

channels: Slide one mesh sleeve (T) over

each cable. Use cable ties (S) to tighten mesh

sleeves to cables.

Pull cords through cord management

channels, leaving enough slack to allow full

range of movement for swing arm assembly

3-1

ﬁg 3.1

To route cables using cable management clips:

Snap eight cable management clips(R) into both

swing arms (C) as shown in ﬁgure 3.2. Cable ties

(S) are used with clips for cord management.

Slide one mesh sleeve (T) over each cable. Use

cable ties (S) to tighten mesh sleeves to cables.

CORD

MANAGEMENT

CHANNEL C

3-1

Note: There are three mounting positions.

The center position is shown right. Arm

assemblies must be mounted with one

mounting hole separating them. Slide washers

(J) over wall support arm axles (D). Next, insert

plastic caps (N) into axles. Then, insert holding

pins (M) into axles. See detail 1.

Note: Fit of axles (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

Insert socket cap screws (K) into hole at bottom

of wall support arm axles (D) as shown in detail 3.

Tighten screw using 9/64" allen wrench (Q).

Place arm assembly (C) with washers (J) into

wall plate (A). Insert axle assemblies shown in

detail 1 through wall plate (A), arm assembly (C),

and washers (J). Lock axles in place by aligning

holding pins (M) with notches shown in detail 2.

2-1

2-2

DETAIL 3

NOTCH

DETAIL 2

DETAIL 1

ﬁg 3.2

• If you are uncertain that product is properly installed, call customer care.

WARNING

7 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B). Attach tilt-roll assembly to adapter bracket with

four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

Note: Adapter bracket (not UL evaluated, sold separately) will vary in size and style.

NOTE: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceed-

ing with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard

race. It is not used with this product.

• Do not overtighten screws! Overtightening may hin-

der roll option.

CAUTION

GENERIC

ADAPTER BRACKET

Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on

arm assembly (C).

Insert one ﬁnishing cap (L) into each unused hole of wall plate (A).

4-1

SWIVEL BOX

8 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Insert two M10 screws (F) into swivel box on arm assembly (C). Leave approximately 1/4" of exposed thread.

• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.

WARNING

SWIVEL BOX

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in ﬁgure 6.1. Install nylon washer (G) and tilt

adjustment knob (H).

Install remaining two M10 screws (F) as shown in

ﬁgure 6.2. HAND TIGHTEN all four M10 screws to

allow for tilt adjustment. Remove tape from carriage

bolt (I). For tilt adjustment, gently push back on the

top of plasma to relieve pressure on knob. Adjust tilt

to desired position and tighten tilt adjustment knob

(H), then securely tighten all four M10 screws (F)

using 6 mm allen wrench (U).

6-1

6-2

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

SWIVEL BOX ﬁg 6.1 ﬁg 6.2

.25" F

9 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

77-1

Depending on the speciﬁc size & weight of the plas-

ma, articulating swing arm may be angled at different

positions, causing plasma to appear to lean sideways

at different articulating positions. Tilt roll assembly (B)

allows plasma to be manually adjusted, so plasma

can be horizontal at all positions. To adjust, gently

rotate plasma by hand to desired position.

Position of screen may be adjusted vertically up to .79"

in each direction by doing the following:

• To raise screen, turn hex nut shown in ﬁgure 8.1

clockwise with 3/4" open-end wrench (not provided).

• To lower screen, turn hex nut shown in ﬁgure

8.1 counterclockwise with 3/4" open-end wrench (not

provided).

If it is too difﬁcult to adjust roll of plasma, loosen

screws shown in ﬁgure 7.1 using a phillips screw-

driver.

IMPORTANT! Do not loosen or tighten screws

more than 1/8 turn.

ARTICULATING

ARM

PLASMA

ﬁg 7.1

ROLL

ADJUSTMENT

SCREWS

HEX

NUT

ﬁg 8.1

All other brand and product names are trademarks or registered trademarks of their respective owners.

10 of 10 ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)

Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal

use, for a period of ﬁve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).

At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.

In no event shall the duration of any implied warranty of merchantability or ﬁtness for a particular purpose be longer than the period of the applicable

express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,

(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,

using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.

In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured

by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other

person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.

This warranty gives speciﬁc legal rights, and you may also have other rights which vary from state to state.

LIMITED FIVE-YEAR WARRANTY

www.peerless-av.com

Autres manuels peerless-AV Support TV

peerless-AV

peerless-AV PTL635 Manuel utilisateur

peerless-AV

peerless-AV PRG3-EXA Manuel utilisateur

peerless-AV

peerless-AV SFL624 Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT LT TV-MT-SFL637 Manuel utilisateur

peerless-AV

peerless-AV ACC-V1500X Manuel utilisateur

peerless-AV

peerless-AV FS-MIS38426 Manuel utilisateur

peerless-AV

peerless-AV ACC953 Mode d’emploi

peerless-AV

peerless-AV Designer SUA747PU Series Manuel utilisateur

peerless-AV

peerless-AV LCZ-4F430B Mode d’emploi

peerless-AV

peerless-AV KIL740 Manuel utilisateur

peerless-AV

peerless-AV SGLS01 Mode d’emploi

peerless-AV

peerless-AV DS508 Mode d’emploi

peerless-AV

peerless-AV Paramount PT660 Manuel utilisateur

peerless-AV

peerless-AV ACC450 Mode d’emploi

peerless-AV

peerless-AV SAX755PU Mode d’emploi

peerless-AV

peerless-AV tru-vue TRWS350/BK Manuel utilisateur

peerless-AV

peerless-AV DS-S555-4X3 Manuel utilisateur

peerless-AV

peerless-AV SA771P Mode d’emploi

peerless-AV

peerless-AV ACC955 Mode d’emploi

peerless-AV

peerless-AV PT640 Manuel utilisateur

peerless-AV

peerless-AV ACCXT101 Mode d’emploi

peerless-AV

peerless-AV ACC-DSV449-P Mode d’emploi

peerless-AV

peerless-AV DS-MBY942L-2X1 Manuel utilisateur

peerless-AV

peerless-AV MIS987 Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

peerless-AV PLAV70 Mode d’emploi

Manuels Support TV populaires d'autres marques