Peerless-AV PDW T XL Mode d’emploi

1 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Installation and Assembly:

Model: PDW T XL

Manufactured by Peerless-AV

Max. Load Capacity:

225 lbs (102 kg)

Display Range:

65”-80” (165-203 cm)

Landscape/Portrait Tiltable X-Large Wall Mount for 65”-80” Flat Panel Displays

2 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................4

Installation to Solid Concrete or Cinder Block Wall ................................................................................................................5

Attaching Adapter Brackets to Display ...................................................................................................................................6

Securing Display to Mount......................................................................................................................................................6

Tilt Adjustment ........................................................................................................................................................................7

• Do not begin to install your product until you have read and understood the instructions and warnings contained in

this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers

please call customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity (See page one).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Metal Stud Contact Qualied Professional

• Brick Contact Qualied Professional

• Other or unsure? Contact Qualied Professional

WARNING

• stud nder ("edge to edge" stud nder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

Tools Needed for Assembly

• hammer

• 3/8” socket

• phillips screw driver

• Pencil

• Measuring tape

• ratchet

3 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Parts (Before beginning, make sure you have all parts shown below).

C (1)

wall plate

Parts List

Part Description Quantity Part Number

Aleft tilt bracket 1 201-1474

Bright tilt bracket 1 201-1476

Cwall plate 1 201-1944

D4 mm allen wrench 1 560-1727

E#14 x 2.5" wood screw 4 5S1-015-C03

F8 mm concrete anchor 4 590-0320

GM5 x 12 mm socket pin screw 4 520-1064

HM5 x 25 mm socket pin screw 4 520-1122

IM6 x 12 mm socket pin screw 4 520-1050

JM6 x 25 mm socket pin screw 4 520-1211

KM8 x 12 mm socket pin screw 4 520-1724

LM8 x 25mm socket pin screw 4 520-1101

Mspacer 4 540-1059

NM4/M5/M6 multi washer 4 580-1398

B (1)

right adapter bracket

A (1)

left adapter bracket

F (4)

8mm concrete anchor

E (4)

#14 x 2-1/2" wood screw

D (1)

allen wrench

M5/M4/M6 washer

N (4)

M8 x 12 mm

K (4)

M8 x 25 mm

L (4)

spacer

M (4)

G (4)

M5 x 12 mm

H (4)

M5 x 25 mm

I (4)

M6 x 12 mm

J (4)

M6 x 25 mm

4 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Installation to Wood Stud Wall

Use a stud nder to locate the edges of the stud. Use of an edge-to-edge stud nder is highly recommended.

Based on their edges, draw a vertical line down the stud center. Place wall plate (C) on wall as a template. Level

plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud center

line. Drill four 5/32" (4 mm) dia. holes 2-1/2" (64 mm) deep. Make sure that the wall plate (C) is level and secure

it using four #14 x 2.5" wood screws (E) as shown below.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations.

WARNING

5 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Installation to Solid Concrete or Cinder Block Wall

• When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90

specications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a ham-

mer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall

plaster/

drywall

concrete concrete

Drill holes and insert anchors (F).

Place plate (A) over anchors (F) and secure with screws (E).

Tighten all fasteners.

concrete

surface

Make sure that wall plate (C) is level, use it as a

template to mark four mounting holes. Drill four

5/16" (8 mm) dia. holes to a minimum depth of 2.5"

(64 mm). Insert anchors (F) in holes ush with wall

as shown. Place wall plate (C) over anchors and

secure with four #14 x 2.5" screws (E). Level, then

tighten all fasteners.

• Tighten screws so that wall plate is rmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

nishing material. If mounting to concrete surfaces

covered with a nishing surface is unavoidable,

the nishing surface must be counter bored as

shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16 mm), custom

fasteners must be supplied by installer.

WARNING

6 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Center adapter brackets vertically on the back of the display. Secure adapter brackets (A and B) to display using

appropriate hardware combination as shown below for specic display application.

Attaching Adapter Brackets to Display

Back of Display

Use of spacers is OPTIONAL

Hook display assembly onto wall plate (C). Position display in desired location and tighten security screw.

Securing Display to Mount

Tighten.

7 of 7ISSUED: 2013-07-02 SHEET #: 125-9459-1 2013-07-02

Tighten.

Pre-set tilt positions of

-5°, 0°, 5°, 10° or 15°.

Tighten

It may be necessary to reposition the ratchet

handle without tightening the assembly

-5°, +15°

Display angle can be adjusted by loosening the ratcher handle and phillips screws. Set display at desired angle and

and secure all hardware.

Note: It is not necessary to completely remove hardware from

assembly to adjust the tilt.

Tilt Adjustment

Table des matières

Autres manuels peerless-AV Support TV

peerless-AV

peerless-AV KIP642-EUK Manuel utilisateur

peerless-AV

peerless-AV DS-MBZ942L-3X1 Manuel utilisateur

peerless-AV

peerless-AV DS-LEDP Series Manuel utilisateur

peerless-AV

peerless-AV PLP PAN42 Mode d’emploi

peerless-AV

peerless-AV Neptune Manuel utilisateur

peerless-AV

peerless-AV PLA60 Mode d’emploi

peerless-AV

peerless-AV ACCXT200 Mode d’emploi

peerless-AV

peerless-AV SmartMount SA771PU Manuel utilisateur

peerless-AV

peerless-AV ACC955 Mode d’emploi

peerless-AV

peerless-AV SMARTMOUNT ST680-S Manuel utilisateur

peerless-AV

peerless-AV ESA763PU Manuel utilisateur

peerless-AV

peerless-AV ECMU-01-I-S Mode d’emploi

peerless-AV

peerless-AV SS560DPB Mode d’emploi

peerless-AV

peerless-AV ACC-DSV449-P Mode d’emploi

peerless-AV

peerless-AV PRG3-EXA Manuel utilisateur

peerless-AV

peerless-AV ACC450 Mode d’emploi

peerless-AV

peerless-AV SUF640P Manuel utilisateur

peerless-AV

peerless-AV PFT640 Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT LT TV-MT-SFL637 Manuel utilisateur

peerless-AV

peerless-AV DS-MBY942L-2X1 Manuel utilisateur

peerless-AV

peerless-AV ACC 050 Mode d’emploi

peerless-AV

peerless-AV STL624 Manuel utilisateur

peerless-AV

peerless-AV PT640 Manuel utilisateur

peerless-AV

peerless-AV ACCXT101 Mode d’emploi

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

peerless-AV PDW T XL Mode d’emploi

Manuels Support TV populaires d'autres marques