Panasonic EY75A8 Manuel utilisateur

© Panasonic Corporation 2018. All rights reserved.

Unauthorized copying and distribution is a violation

of law.

ORDER NO. PTD1806X47CE

Cordless Impact Wrench

Model No. EY75A8

Europe

Oceania

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 6

5 Exploded View and Replacement Parts List -----------10

2

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70 °F (30 - 40 °C) higher.

Please use a soldering iron with temperature control and adjust it to 750 ± 20 °F (400 ± 10 °C). In case of using high temperature

soldering iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600 °C).

2 Specifications

3

3 Troubleshooting Guide

3.1. Troubleshooting Guide

4

5

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

• Confirm all screws are tightened firmly.

• Confirm if there is no dirt when repairing.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the LED lights ON.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool speed is normal after repair and reassembly.

High mode: 0 to 2300 rpm at 14.4V, 0 to 2500 rpm at 18V.

Medium mode: 0 to 1500 rpm at 14.4V/18V.

Low mode: 0 to 1000 rpm at 14.4V/18V.

• Check whether the remaining battery power indicator lamp lights up or flashes when the Battery level button is pressed.

6

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-4 and proceed to 4-1

4.1. How to remove the Housing.

4.2. How to remove the Driving assembly.

1. After removing the plate hook, remove 4 DPT sems tapping screws.

2. Remove 9 housing screws.

3. Then open the housing B.

4. Remove the interior parts.

5. Remove the interior components from the housing A.

Note: (when assembling)

Route LED lead wires and motor lead wire between the ribs on housing

A like the figure.

Hold the motor assembly, remove the driving cover assembly and asso-

ciated parts together from the motor assembly.

7

4.3. How to remove the Driving cover assembly and Driving shaft assembly.

Note: (when assembling)

1. Remove the protector.

2. Remove the interior components from the driving cover

assembly.

8

4.4. How to remove the Switch assembly, LED harness assembly and

Battery terminal.

Note: (when assembling)

The connect cover cannot be reused after being repaired.

NOTE:(When attaching the connectors/switch).

Apply grease (Permalub) to the indicated by the shaded area.

1. Remove the connector(6-pin/2-pin) covers.

2. Disconnect the connecters or lead wires in order to (1) to (4).

Note:

Exercise care not to bend the terminal fitting.

9

4.5. Wiring and Assembly Points.

Model No. : EY75A8 Exploded View

5 Exploded View and Replacement Parts List

Autres manuels pour EY75A8

2

Table des matières

Autres manuels Panasonic Outils électriques

Panasonic

Panasonic EY46A5 Manuel utilisateur

Panasonic

Panasonic EY4541X Manuel utilisateur

Panasonic

Panasonic EY75A8 Manuel utilisateur

Panasonic

Panasonic EY4550 Manuel utilisateur

Panasonic

Panasonic EY74A2X Manuel utilisateur

Panasonic

Panasonic EY7550LR2S Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EY75A8 Manuel utilisateur

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic 7552LJ Manuel utilisateur

Panasonic

Panasonic EYFLA4 Manuel utilisateur

Panasonic

Panasonic EYFLA9C Manuel utilisateur

Panasonic

Panasonic EYFMH1WC Manuel utilisateur

Panasonic

Panasonic EY74A2 Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EYFPA1C Manuel utilisateur

Panasonic

Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG Manuel utilisateur

Panasonic

Panasonic EYFLC1A Manuel utilisateur

Panasonic

Panasonic AccuPulse QP Low Noise Series Manuel utilisateur

Panasonic

Panasonic EY3610 Manuel utilisateur

Panasonic

Panasonic EYFPA1J Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EYFEA1N Mode d'emploi

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel