Panasonic EYFPA1J Manuel utilisateur

Unauthorized copying and distribution is a violation

of law.

Order Number PTD1512E07CE

Cordless Impact Wrench

Model No. EYFPA1J

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ---------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 8

5 Wiring Connection Diagram ---------------------------------19

6 Schematic Diagram ---------------------------------------------19

7 Appendix -----------------------------------------------------------20

8 Exploded View and Replacement Parts List -----------21

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

2 Specifications

NOTE:

Weight indication

Greater than or equal to 1 kg : indicated by 0.05kg

Less than 1 kg : indicated by 0.01 kg.

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Set the LED light to d1 mode and check whether the LED light turns on when the trigger is engaged and that it turns off when the

trigger is released.

• Set the LED light to d2 mode and check whether the LED light turns on when the trigger is engaged and that it turns off when the

trigger is released.

• Set the buzzer to each of its three modes and verify that there is no buzzer in b0 mode, that the buzzer sounds when the green

lamp is on in b1 mode, and that the buzzer sounds when the red lamp is on b2 mode.

• Confirm that the LED light automatically turns off when no operation is performed for 5 minutes or more while the LED light is lit.

• Check whether the tool speed is normal after repair and reassembly.

Rotating speed: 0 to 1900 rpm

• Check whether the tool become hot in a short operation.

• Check whether the ID setting has been properly configured after repair and reassembly.

1. Press D button on the remote control.

2. Confirm the operation panel display.

• Initializing all settings (revert settings to factory defaults).

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

• Verify that there is no dirt, scratching, or other damage on the tool’s exterior from the repair process.

(Check the shaft cover assembly carefully for surface scratches since it is made of aluminum.)

4 Disassembly and Assembly Instructions

*To reduce the risk of injury, always remove battery pack before removing/installing the tool.

*To assemble the tool, start with 4.10 and proceed to 4.1.

4.1. How to remove the housing B

4.2. How to remove the thrust plate, anvil, and the cap from the shaft cover

assembly

4.3. Remove the interior components

Autres manuels pour EYFPA1J

Table des matières

Autres manuels Panasonic Outils électriques

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EY74A2X Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic EYFLA5A Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic 4541OLOA Manuel utilisateur

Panasonic

Panasonic EY7549 Manuel utilisateur

Panasonic

Panasonic EY46A5 Manuel utilisateur

Panasonic

Panasonic EY4542 - CIRCULAR SAW 14.4V Manuel utilisateur

Panasonic

Panasonic EY75A8 Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EYFMH1WC Manuel utilisateur

Panasonic

Panasonic EY4541X Manuel utilisateur

Panasonic

Panasonic EYFLA4 Manuel utilisateur

Panasonic

Panasonic EY3610 Manuel utilisateur

Panasonic

Panasonic EYFMA1B Manuel utilisateur

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EY4550 Manuel utilisateur

Panasonic

Panasonic EY75A8 Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EY4550 Manuel utilisateur

Panasonic

Panasonic EY7550LR2S Manuel utilisateur

Panasonic

Panasonic EYFME1C Manuel utilisateur

Panasonic

Panasonic EYFPA1C Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel