Panasonic EY7549 Manuel utilisateur

distribution is a violation of law.

Order Number PTD1301X19CE

Cordless Multi- Impact & Drill Driver

Model No. EY7549

Europe

Oceania

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 8

5 Wiring Connection Diagram ---------------------------------15

6 Schematic Diagram ---------------------------------------------15

7 Exploded View and Replacement Parts List -----------16

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

2 Specifications

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (After Checking Troubleshooting Guide)

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• Confirm all screws are tightened firmly.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the LED light turns on and off each time the LED light on/off button is depressed.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool speed is normal after repair and reassembly.

*Please refer to the specifications on page 2.

• Check whether the tool may become hot in a short operation.

• Set the clutch handle to the mark and check whether the tool rotates without any clutch operation.

• Pull the trigger all the way back and check whether the tool stops rotating immediately when it is released.

• Rotate the clutch handle and check whether the clutch switches properly.

• Check whether impact operation functions properly.

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

• Check for the presence of any dirt or foreign matter from the repair process on the outside of the tool.

4 Disassembly and Assembly Instructions

*To assemble the tool, start with 4-12 and proceed to 4-1

4.1. Removing the plate hook

4.2. Removing the Fixation cover assembly

4.3. Removing the housing

4.4. Removing the switch assembly

4.5. Removing the Module assembly

Autres manuels pour EY7549

Table des matières

Autres manuels Panasonic Outils électriques

Panasonic

Panasonic EY3610 Manuel utilisateur

Panasonic

Panasonic EY4541 Manuel utilisateur

Panasonic

Panasonic EYFMH1WC Manuel utilisateur

Panasonic

Panasonic EYFPA1C Manuel utilisateur

Panasonic

Panasonic EYFLA5A Manuel utilisateur

Panasonic

Panasonic EY7552X57 Manuel utilisateur

Panasonic

Panasonic EY46A5 Manuel utilisateur

Panasonic

Panasonic EY74A2X Manuel utilisateur

Panasonic

Panasonic EYFLA4 Manuel utilisateur

Panasonic

Panasonic EY4542 - CIRCULAR SAW 14.4V Manuel utilisateur

Panasonic

Panasonic EYFME1C Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic EYFEA1N Mode d'emploi

Panasonic

Panasonic EY3640 Manuel utilisateur

Panasonic

Panasonic AccuPulse QP Low Noise Series Manuel utilisateur

Panasonic

Panasonic EY4550 Manuel utilisateur

Panasonic

Panasonic EYFPA1J Manuel utilisateur

Panasonic

Panasonic 4541OLOA Manuel utilisateur

Panasonic

Panasonic EY4541X Manuel utilisateur

Panasonic

Panasonic EY4550 Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic 7552LJ Manuel utilisateur

Panasonic

Panasonic EY46A5 Manuel utilisateur

Panasonic

Panasonic EY75A8 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel