olympia electronics Double Easy Light GR-391/L Manuel utilisateur
GENERAL
o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each luminaire must be permanently
connected to mains power supply.
Iin normal operation the battery is charging
and the 2 yellow LED’s light in each side of
the screen.
In case of a mains power supply failure
th e lu min air e will lig ht t he l ed s trip
automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only.
2. The device must be connected to the
ma in s p ower s up pl y thro ug h a fuse
dependent by the total amount of the line’s
power load.
3. It is suggested to check every month the
indication LED for battery charging, and by
pushing the TEST button to check the
emergency circuit. The lamp should light as
long as the TEST button is pressed
4. It is suggested to check every 6 months
the minimum autononous duratio n by
disconnecting the mains power supply. Count
the time that the led strip lights and in case
of less time than the minimum autonomous
duration the battery must be replaced. If the
measured time is considerably less than the
minimum autonomous duration
In case of battery or led strip
replacement, these must be replaced by
parts of the same type, by the manufacturer
or by a competent person.
t i
in battery recycling
points.
. In the
opposite condition contact the installer.
contact the
installer.
5. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in
to common trash bins, they must be
discarded only
923393000_09_008
Page 1 from 4
NON MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs
ABS/PC, PC
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
ILLUMINATION SOURCE
24h
Battery charging LED, TEST button
From overcharge and deep discharge
IP40
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)
350 x 134 x 60 mm (CRV 362 x 134 x 90 mm)
GR-393/L GR-391/L
220-240V AC/50-60Hz
3.6V/3Ah3.6V/1.5Ah
4W/ 4.3VA2.5W/ 3VA
180 min90 min
270lm
2X16 LED
940gr (CRV 1020gr) 1030gr (CRV 1110gr)
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 4)
Congratulations for your selection to buy this product.
Olympia Electronics - European manufacturers.
Page 2 from 4923393000_09_008
PLACING Α-CRV PARTS
To install the curve crystal Α-CRV you must first install the
included plastic extension to mount it on the TEST button.
MARKING PANEL SP-114
A marking panel SP-114 can be installed on the
luminaire in 3 different locations. This marking
panel is installed perpendicular to the diffusor of
the luminaire, as shown on the pictures below.
The panel is pre-printed and has a plastic
accessory on each side that is used to fasten the
panel to the luminaires.
There are 2 arrow stickers that can be placed in
each side of the marking panel to point to the
desired direction.
Placing the SP-114 marking panel
Place the plastic mounting accessories of the
marking panel as shown on pictures.
ΝΟΤΕ!! This marking panel (SP type) can not
be installed on CRV luminaires.
362 134
134
90
Test
Double Easy Light
luminaires
60
134
350
134
Double Easy Light
luminaires
/CRV
Battery replacement.
It can be done only by a competent person and after the mains
interruption.
1. Turn the luminaire anti-clockwise and detach it from its
mounting base. Use a flat blade screwdriver and remove the
diffusors.
2. Unfasten the reflector’s retaining screws.
3. Disconnect the connector and remove the old battery.
4. Connect the new battery with the same type and place it in
the position of the old one.
5. Replace the removed parts (step 1 and 2) and power the
device.
2
Plastic base
Diffusor Diffusor
Reflector
1
Page 3 from 4
INSTALLATION INSTRUCTIONS
1 Pass through the central hole of the plastic base the luminaire’s cables and connect them to the
included terminal block (figure 1). Ν for neutral, L for live wire.
2 Use the included mounting accessories to install the plastic base (install the notch, facing the
required direction of the luminaire) and follow the mounting methods on the wall or ceiling.
o
3 Install the luminaire to the plastic base by turning it clockwise by 90 and then power it, with the
mains power supply.
220-240V AC/50-60Hz
Blue-grey
Brown
L
N
Ν - Blue-grey
L - Brown
Figure 2: Connecting to the mains power supply
Connecting to the mains power supply
Connecting the terminal block
Male terminal block
Female terminal block
Base
Luminaire
Figure 1
Side view
on ceiling attached
Front view
on ceiling attached
Front view
wall mounted
Downside view
wall mounted
Power supply Cable
Mounting methods
923393000_09_008
Plastic base
Diffusor Diffusor
Reflector
1
2
3
NOTE!! After finishing the installation you must power the luminaire at least for 24 hours for
battery charging to perform the nominal autonomy.
Page 4 from 4923393000_09_008
NOTE!! If you don’t need the yellow
leds to light in normal operation,
then remove the led jumper.
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
47 °C max. across the board
Non reversible cable connection between main pcb and led module
11.6 - 14.4V DC
2W
1410133
GR-391/L
GR-393/L
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained (*)
A: Including test device
G: Internally illuminated
*90: 1.5 hour duration
180: 3 hour duration
Note!! The installer should fill in, on the specification label,
the letter G if the luminaire is used as a safety sign.
LED JUMPER
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
X09
*0A G
Ce manuel convient aux modèles suivants
3
Autres manuels olympia electronics Lanterne
olympia electronics
olympia electronics KLIN-20/ST Manuel utilisateur
olympia electronics
olympia electronics CLASSIC LIGHT Series Manuel utilisateur
olympia electronics
olympia electronics KLIN-20/ST/ADR Manuel utilisateur
olympia electronics
olympia electronics GR-490/ADR Manuel utilisateur
olympia electronics
olympia electronics OLY-1024/WL Manuel utilisateur
olympia electronics
olympia electronics GR-292/M/HL Manuel utilisateur
olympia electronics
olympia electronics OLY-1004/WP/ADR Manuel utilisateur
olympia electronics
olympia electronics POWER LIGHT Series Manuel utilisateur
olympia electronics
olympia electronics WEATHER LIGHT Series Manuel utilisateur
olympia electronics
olympia electronics GRL-37/90/ADR Manuel utilisateur
olympia electronics
olympia electronics GR-8/leds Manuel utilisateur
olympia electronics
olympia electronics GR-427/12L/MAR Manuel utilisateur
olympia electronics
olympia electronics OLY-1004 Manuel utilisateur
olympia electronics
olympia electronics GR-796/ST/DUO/ADR Manuel utilisateur
olympia electronics
olympia electronics Slim Light Series Manuel utilisateur
olympia electronics
olympia electronics GR-427/12L Manuel utilisateur
olympia electronics
olympia electronics GR-938/15L Manuel utilisateur
olympia electronics
olympia electronics GR-270 Manuel utilisateur
olympia electronics
olympia electronics GR-579/L/90/WP Manuel utilisateur
olympia electronics
olympia electronics GR-2110 Manuel utilisateur
