Olympia electronics WEATHER LIGHT Series Manuel utilisateur

Thank you for purchasing this product of

Olympia Electronics. A European

manufacturer.

GENERAL

These luminaires are used in places where

emergency luminaires are needed.

Each luminaire must be permanently

connected to mains power supply. In normal

operation the battery is charging and the 2

yellow LED’s light in the screen (see step 4

on page 2).In case of a mains power

supply failure the luminaire will light the

led strip automatically in emergency mode.

When the mains power supply is restored

the device turns to normal operation.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personel only.

2. The device must be connected to the

mains power supply thru a fuse dependent

by the total amount of the line’s power load.

3. It is sugested to check every month the

indication LED for battery charging, and by

pushing the TEST button (see the paragraph

9 on page 2), to check the emergency cirquit.

The lamp should light as long as the TEST

button is pressed. In the opposite condition

contact the installer.

4. It is sugested to check every 6 months the

minimum autononous duration by

disconnecting the mains power supply. Count

the time that the led strip lights and in case of

less time than the minimum autonomous

duration the battery must be replaced. If the

measured time is considerably less than the

minimum autonomous duration

The replacement of the battery and

the light source must be done using parts of

the same type, by the manufacturer or by a

competent person.

t i

in battery recycling

points. Do not incinerate.

contact the

installer.

5. In case of inactive use for a period greater

than 2 months, disconnect the battery by

pulling out the battery’s connector.

6. I s not allowed to discard batteries in

to common trash bins, they must be

discarded only

INSTALLATION

To install the luminaire follow the installation

instructions οn page 2.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non Maintained

A: Including test device

*90: 90min duration

180: 180min duration

‘’ WEATHER LIGHT ‘’ SERIES FOR NON-MAINTAINED EMERGENCY LUMINAIRES

Page 1 from 2 923936006_23_011

High Quality European based Manufacturers

220-240V AC/50-60Hz

Bayblent FR3010, transparent polycarbonate

TECHNICAL CHARACTERISTICS

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

ILLUMINATION SOURCE 180min90min 24h

Charge indication LED, TEST button

From overcharge and full discharge

300lm 300lm450lm 415lm

4 power LED’s 4 power LED’s 6 power LED’s6 power LED’s

0 to 40 C

Up to 95%

3 years (1 year for the battery)

363 x 145 x 73 mm

4.8V/1.5Ah 4.8V/3Ah 4.8V/4Ah(Ni-MH)

950gr. 980gr. 1020gr.

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

IP 65

4,8VA 5,5VA4VA

GR-935/6P GR-936/4P GR-936/6P

GR-935/4P

Page 2 from 2

1Remove the diffusor.Place simultaneously 2 flat blade screwdrivers and pull up gently the

reflector.

2Install the included plastic cover in to the unused hole and install the base plastic (with the

included mounting screws and plugs).

3Always use in any case round mains cable,with external diameter of 6-9mm (H05RN-F type

2x1mm² or any other type,at least equal to it’s mechanical and electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is important to

ensure the tightness isolation IP 65). Install the cable gland,pass the round cable thru and

tighten it all the way.

4Place the battery’s connector to the corresponding connector on the P.C.B. NOTE!! If you don’t

need the yellow led’s to light in normal operation, then remove the led jumper.

5Connect the mains as shown in figure (connect the ground wire if required).

6Install the included tie (if needed) to fasten securely the power cables.

7Refit the reflector and fasten the two small screws (included).

8Finaly place the diffusor by using the 4 included screws (tightening torque 1.2Nm).

INSTALLATION INSTRUCTIONS

L N

Mains connection

923936006_23_011

LED

JUMPER

NOTE!! After finishing the installation you must power the

luminaire at least for 24 hours for battery charging to perform the

named autonomy.

9 Unfasten the mounting screws (step 8) and remove the diffusor.

When the luminaire is supplied by the mains, press on the marking

for TEST as shown in the picture below. Mount the diffusor by using

the 4 removed screws.

TEST procedure with extra care!!

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Follow the step 1of the installation procedure. Unfasten the 2 retaining screws and remove the

reflector (photo step 7).

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 4of the installation procedure) and place it

in the position of the old one.

4. Follow the step 7 and 8 of the installation procedure and power the device.

Ce manuel convient aux modèles suivants

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics GRL-29 WP Manuel utilisateur

olympia electronics

olympia electronics GR-2100/ST Manuel utilisateur

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics LLB-26/90 Manuel utilisateur

olympia electronics

olympia electronics GR-900/30L/SC Manuel utilisateur

olympia electronics

olympia electronics GR-490/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-290/WP/M Manuel utilisateur

olympia electronics

olympia electronics GRL-37/90/WP Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

olympia electronics

olympia electronics Power Light Series Manuel de l'opérateur

olympia electronics

olympia electronics GR-290 Manuel utilisateur

olympia electronics

olympia electronics GR-940/15L/MAR Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics EASY LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-938/15L Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L/MAR Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP/ADR Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur