Olympia electronics GR-2110 Manuel utilisateur

220-240V AC/50-60Hz

3 h

24 h

IP 30

3.6V/1Ah

3W / 3.5VA

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

5 to 40 C

up to 95%

Bayblend FR3010, transparent polycarbonate

495gr.

292 x 111 x 54 mm

40lm / 100lm

12 White LEDs

923211002_09_004

Page 1 from 3

‘’ SLIM CLASSIC LIGHT ‘’ SERIES FOR NON MAINTAINED / MAINTAINED

(OPTIONAL) EMERGENCY LUMINAIRES

GENERAL

These luminaires are used indoors (ta 40 C)

where emergency light is needed.

Each luminaire must be permanently

connected to mains power supply. In normal

operation the illumination LEDs are lit as well

as the green indicating charge LEDs when

the battery is charging.

In case of a mains power supply failure the

luminaire will light the led strip automatically

in emergency mode. When the mains power

supply is restored the device turns to normal

operation.

Non Maintained / maintained operation

th e re i s an o pti o n t o sel e ct t he n o n

maintained or maintained operation by

placing the jumper to the appropriate place

according to the figure 3 (page 2).

INSTALLATION

To install the luminaire follow the installation

instructions on page 2.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel

only.

2. The device must be connected to the

m a i n s p o w e r su p p l y th r o u gh a f u s e

dependent by the total amount of the line’s

power load.

3. It is suggested to check every month the

indication LED for battery charging, and by

pushing the TEST button to check the

emergency circuit. The led strip should light as

long as the TEST button is pressed. If the

luminaire doesn’t work as described above

contact the installer.

4. It is suggested to check every 6 months the

m i n i m u m a u t o n o n o u s d u r a t i o n b y

disconnecting the mains power supply. Count

the time that the led strip lights and in case of

less time than the minimum autonomous

duration the battery must be replaced. If the

measured time is considerably less than the

minimum autonomous duration contact the

installer. In case of battery or led strip

replacement, these must be replaced by parts

of the same type, by the manufacturer or by a

competent person.

5. In case of inactive use for a period greater

than 2 months, disconnect the battery by

pulling out the battery’s connector.

6. I s not allowed to discard batteries in to t i

c o m m o n t r a s h b i n s , t h e y m u s t b e

discarded only in battery recycling

points. Do not incinerate.

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (230V AC / emergency)

ILLUMINATION SOURCE

Battery charge indication LEDs, TEST button

3 years (1 year for the battery)

GR-2110

Thank you for your trust in our products.

Olympia Electronics - European manufacturer.

TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 3)

923211002_09_004

Page 2 from 3

Figure 4

Figure 1

Figure 3

Non-maintained

operation

Maintained

oparation

1. To instal the device you have to dismantle carefully the device with a flat screwdriver as

shown in figure 1.

2. Pass the mains cables through the hole (point 1 in figure 2). The luminaire must be

connected to a permanent electrical installation to ensure the immobilization of the cable.

3. Mount the base plastic on the wall by using the included mounting accessories in points 2

and 3 in figure 2.

4. Connect the battery`s cable with the appropriate terminal (figure 3).

5. Connect the mains cables to the terminal block as shown in figure 4.

6. Refit with care the removed plastic parts and power on the luminaire.

NOTE!!

After finishing the installation you must power the luminaire at least for 24 hours for

battery charging to perform the nominal autonomy.

Installation instructions

Connection terminal

block on the PCB

For fuce ratings

see text

Battery replacement.

It can be done only by a competent person and after the mains supply interruption.

1. Dismantle the device (step 1 of the installation instructions).

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 4 of the installation instructions) and

place it in the position of the old one.

4. Follow the step 6 of the installation procedure and power the device.

(*) Maintained operation: The luminaire lights its

illumination source, when it is powered by the mains

power supply or not.

Non Maintained operation: The luminaire lights its

illumination source, only in power supply’s failure.

Note!! The installer should fill in, on the specification label,

the letter G if the luminaire is used as a safety sign.

X1 1 8 0A G

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

180: 3 hours duration

Figure 2

923211002_09_004

Page 2 from 3

Figure 4

Figure 1

Figure 3

Non-maintained

operation

Maintained

oparation

1. To instal the device you have to dismantle carefully the device with a flat screwdriver as

shown in figure 1.

2. Pass the mains cables through the hole (point 1 in figure 2). The luminaire must be

connected to a permanent electrical installation to ensure the immobilization of the cable.

3. Mount the base plastic on the wall by using the included mounting accessories in points 2

and 3 in figure 2.

4. Connect the battery`s cable with the appropriate terminal (figure 3).

5. Connect the mains cables to the terminal block as shown in figure 4.

6. Refit with care the removed plastic parts and power on the luminaire.

NOTE!!

After finishing the installation you must power the luminaire at least for 24 hours for

battery charging to perform the nominal autonomy.

Installation instructions

Connection terminal

block on the PCB

For fuce ratings

see text

Battery replacement.

It can be done only by a competent person and after the mains supply interruption.

1. Dismantle the device (step 1 of the installation instructions).

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 4 of the installation instructions) and

place it in the position of the old one.

4. Follow the step 6 of the installation procedure and power the device.

(*) Maintained operation: The luminaire lights its

illumination source, when it is powered by the mains

power supply or not.

Non Maintained operation: The luminaire lights its

illumination source, only in power supply’s failure.

Note!! The installer should fill in, on the specification label,

the letter G if the luminaire is used as a safety sign.

X1 1 8 0A G

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

180: 3 hours duration

Figure 2

Table des matières

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics OLY-500 Manuel utilisateur

olympia electronics

olympia electronics OLY-1004 Manuel utilisateur

olympia electronics

olympia electronics GR-290/WP/M Manuel utilisateur

olympia electronics

olympia electronics SLIM LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics LLB-26/90 Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP Manuel utilisateur

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-796/ST/DUO/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-900/30L/SC Manuel utilisateur

olympia electronics

olympia electronics GR-940/15L/MAR Manuel utilisateur

olympia electronics

olympia electronics Double Easy Light GR-391/L Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-579/L/90/WP Manuel utilisateur

olympia electronics

olympia electronics GRL-37/90/WP Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L Manuel utilisateur

olympia electronics

olympia electronics GR-1935/15L Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GRL-38/90/M Manuel utilisateur

olympia electronics

olympia electronics GR-938/15L Manuel utilisateur

olympia electronics

olympia electronics GR-292/M/HL Manuel utilisateur

olympia electronics

olympia electronics OLY-1004/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics Slim Light Series Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur

olympia electronics GR-2110 Manuel utilisateur

Manuels Lanterne populaires d'autres marques