NXP Semiconductors LPC2880 Manuel utilisateur

UM10208

LPC2880/LPC2888 User manual

Rev. 02 — 1 June 2007 User manual

Document information

Info Content

Keywords LPC2880, LPC2888, LPC288x, ARM, ARM7, embedded, 32-bit,

microcontroller, USB 2.0, USB HS

Abstract LPC288x User manual

User manual Rev. 02 — 1 June 2007 2 of 362

Contact information

For additional information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

NXP Semiconductors UM10208

LPC288x User manual

Revision history

Rev Date Description

02 20070601 Various editorial and content updates to the following chapters:

•The format of this user manual has been redesigned to comply with the new identity

guidelines of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

•Universal Asynchronous Receiver-Transmitter (UART):

The UART baud rate is derived from the UART baud rate clock (UART_CLK).

•External Memory Controller (EMC):

SDRAM Usage notes added (Section 8–12).

•Clock Generation Unit (CGU) and power control:

CGU Usage notes added including a section on how to achieve low-power operation

(Section 7–5).

•USB Device controller:

–DMA mode transfer section was improved (Section 17–6.4).

–Endpoint configuration table added (Table 17–232).

–Section 17–8.6 on interrupt handling was further elaborated.

•I/O pinning:

Section 25–2.5 “Pin structure”added.

•DC-to-DC converter:

Section 6–2 “General operation”was improved.

•SD/MMC interface:

Status register contents were corrected (Table 23–345). Descriptions on bits 17 and 19

were swapped.

•General Purpose DMA controller (GPDMA):

(Table 15–196).

•Dual-channel 16-bit Digital-to-Analog Converter (DDAC):

–Description of Dual DAC was improved.

–Section 22–6.2 “Power-up procedure”was corrected.

•Dual-channel 16-bit Analog-to-Digital converter (DADC):

Bits 0-7 of Decimator Control register were corrected (Table 21–306).

•I2S output module (DAO):

DAO pin description was corrected (Table 20–292).

•Boot process:

Part Identification register (Table 3–4) was moved to this chapter from chapter “System

control ”.

•Chapter “System control” removed.

•Chapter “General Purpose I/O (GPIO)” added.

01 20060905 LPC288x User manual

User manual Rev. 02 — 1 June 2007 3 of 362

1. Introduction

The LPC288x is an ARM7-based microcontroller for portable applications requiring low

power and high performance. It includes a USB 2.0 High Speed device interface, an

external memory interface that can interface to SDRAM and Flash, an MMC/SD memory

card interface, A/D and D/A converters, and serial interfaces including UART, I2C, and I2S.

Architectural enhancements like multi-channel DMA, processor cache, simultaneous

operations on multiple internal buses, and flexible clock generation help ensure that the

LPC288x can handle more demanding applications than many competing devices. The

chip can be powered from a single battery, from the USB, or from regulated 1.8 and 3.3V.

2. Features

•ARM7TDMI processor with 8 kB cache operating at up to 60 MHz

•1 MB on-chip Flash Program Memory with 128-bit access for high performance

•64 kB SRAM

•32 kB ROM

•On-chip DC-DC converter can generate all required voltages from a single battery or

from USB power

•Multiple internal buses allow simultaneous GP DMA, USB DMA, and program

execution from on-chip Flash without contention.

•External memory controller supports Flash, SRAM, ROM, and SDRAM.

•Advanced Vectored Interrupt Controller, supporting up to 30 vectored interrupts

•Innovative Event Router allows interrupt, power-up, and clock-start capabilities from

up to 105 sources

•Multi-channel GP DMA controller that can be used with most on-chip peripherals as

well as for memory-to-memory transfers.

•Serial Interfaces:

–Hi-Speed or Full-speed USB 2.0 Device (480 or 12 Mbits/s) with on-chip PHYsical

layer

–UART with fractional baud rate generation, flow control, IrDA support, and FIFOs

–I2C Interface

–I2S (Inter-IC Sound) interface for independent stereo digital audio input and output

•Secure Digital (SD) / MultiMediaCard (MMC) memory card interface

•10 bit A/D Converter with 5-channel input multiplexing

•16 bit stereo A/D and D/A converters with gain control and optional DMA

•Advanced clock generation and power control reduce power consumption

•Two 32-bit Timers with selectable prescalers

•8-bit LCD interface bus

•Real Time Clock can be clocked by 32 kHz oscillator or another source

•Watchdog Timer with interrupt and/or reset capabilities

UM10208

Chapter 1: Introductory information

Rev. 02 — 1 June 2007 User manual

User manual Rev. 02 — 1 June 2007 4 of 362

NXP Semiconductors UM10208

Chapter 1: LPC2800 Introductory information

•180 pin TFBGA package

3. Applications

•Portable, battery powered devices

•USB devices

4. Architectural overview

The LPC288x includes an ARM7TDMI CPU with an 8kB cache, an AMBA Advanced

High-performance Bus (AHB) interfacing to high speed on-chip peripherals and internal

and external memory, and four AMBA Advanced Peripheral Buses (APBs) for connection

to other on-chip peripheral functions. The LPC288x permanently configures the

ARM7TDMI processor for little-endian byte order.

The LPC288x includes a multi-layer AHB and four separate APBs, in order to minimize

interference between the USB controller, other DMA operations, and processor activity.

Bus masters include the ARM7 itself, the USB block, and the general purpose DMA

controller.

Lower speed peripheral functions are connected to the APBs. Four AHB-to-APB bridges

interface the APBs to the AHB.

5. ARM7TDMI processor

The ARM7TDMI is a general purpose 32 bit microprocessor that offers high performance

and very low power consumption. The ARM architecture is based on Reduced Instruction

Set Computer (RISC) principles, and the instruction set and related decode mechanism

are much simpler than those of microprogrammed Complex Instruction Set Computers.

This simplicity results in a high instruction throughput and impressive real-time interrupt

response from a small and cost-effective processor core.

Pipeline techniques are employed so that all parts of the processing and memory systems

can operate continuously. Typically, while one instruction is being executed, its successor

is being decoded, and a third instruction is being fetched from memory.

The ARM7TDMI processor also employs a unique architectural strategy known as

THUMB, which makes it ideally suited to high-volume applications with memory

restrictions, or applications where code density is an issue.

The key idea behind THUMB is that of a super-reduced instruction set. Essentially, the

ARM7TDMI processor has two instruction sets:

•The standard 32 bit ARM instruction set.

•A 16 bit THUMB instruction set.

The THUMB set’s 16 bit instruction length allows it to approach twice the density of

standard ARM code while retaining most of the ARM’s performance advantage over a

traditional 16 bit processor using 16 bit registers. This is possible because THUMB code

operates on the same 32 bit register set as ARM code.

User manual Rev. 02 — 1 June 2007 5 of 362

NXP Semiconductors UM10208

Chapter 1: LPC2800 Introductory information

THUMB code be as little as 65% of the code size of ARM, and 160% of the performance

of an equivalent ARM processor connected to a 16 bit memory system.

The ARM7TDMI processor is described in detail on the ARM website.

6. On-Chip flash memory system

The LPC2888 includes a 1 MB Flash memory system. This memory may be used for both

code and data storage. Programming of the Flash memory may be accomplished in

several ways. It may be programmed In System via the USB port. The application

program may also erase and/or program the Flash while the application is running,

allowing a great degree of flexibility for data storage and field firmware upgrades.

The Flash is 128 bits wide and includes buffering to allow 3 out of 4 sequential read

operations to operate without wait states.

7. On-Chip Static RAM

The LPC288x includes 64 kB of static RAM that may be used for code and/or data

storage.

8. On-Chip ROM

The LPC288x includes 32 kB of Read Only Memory that may be used for code and/or

constant storage. Execution begins in on-chip ROM after a Reset.

Philips provides a standard boot code in this ROM that reads the state of the Mode inputs

and accordingly does one of the following:

1. starts execution in internal Flash,

2. starts execution in external memory,

3. performs a hardware self-test, or

4. downloads code from the USB interface into on-chip RAM and transfers control to the

downloaded code.

User manual Rev. 02 — 1 June 2007 6 of 362

NXP Semiconductors UM10208

Chapter 1: LPC2800 Introductory information

9. Block diagram

(1) LPC2888 only

Fig 1. LPC288x block diagram

MULTI-LAYER AHB

AIN[4:0]

Px.y

WATCHDOG

TIMER

SD/MMC CARD

INTERFACE

GENERAL

PURPOSE I/O

SYSTEM

CONTROL

EVENT

ROUTER

interface

DC-TO-DC

CONVERTER

START,

STOP

SCL, SDA

MCLK

MD[3:0], MCMD

DATI

BCKI, WSI

AOUTL,

AOUTR

AINL, AINR

DATO

BCKO, DCLKO,

WSO

+1.5 V

or +5 V

3.3 V,

1.8 V

XTALI

XTALO

X32I

X32O

CLOCK

GENERATION

UNIT

OSCILLATOR

AND PLLs

ARM7TDMI-S

JTAG DEBUG

INTERFACE

8 kB CACHE

JTAG_TRST

JTAG_TMS

JTAG_TCK

JTAG_TDI

JTAG_TDO

JTAG_SEL

FLASH

INTERFACE

1 MB

FLASH(1)

SRAM

INTERFACE

64 kB

SRAM

ROM

INTERFACE

BOOT

ROM

REAL-TIME

CLOCK

OSCILLATOR

FIFO FIFO I2S-BUS

INPUT

FIFO I2S-BUS

OUTPUT

DUAL ANALOG

INPUT

FIFO

DUAL ANALOG

OUTPUT

EXTERNAL

MEMORY

CONTROLLER

A[20:0],

D[15:0],

etc.

VECTORED

INTERRUPT

CONTROLLER

HS USB

WITH DMA

DP, DM, VBUS,

RREF, CONNECT

LPC2880/2888

AHB TO APB

BRIDGE 0

AHB TO APB

BRIDGE 3

AHB TO APB

BRIDGE 1

AHB TO APB

BRIDGE 2

GP DMA

CONTROLLER

10-BIT A/D

CONVERTER

UART WITH

IrDA

TXD, RTS

RXD, CTS

LCD

INTERFACE LCD bus

I2C-BUS

INTERFACE

32-BIT

TIMER 0

32-BIT

TIMER 1

002aac296

User manual Rev. 02 — 1 June 2007 7 of 362

1. Memory map and peripheral addressing

ARM processors have a single 4 GB address space. The following table shows how this

space is used on the LPC288x. Addresses not shown in this table are not used.

1.1 Memory map

The LPC2880/2888 memory map incorporates several distinct regions, as shown in

Figure 2–2. When an application is running, the CPU interrupt vectors are remapped to

allow them to reside in on-chip SRAM.

UM10208

Chapter 2: LPC2800 Memory addressing

Rev. 02 — 1 June 2007 User manual

Table 1. LPC288x memory usage

Address range General use Address range details and description

0x0000 0000 to

0x0FFF FFFF Cacheable area 0x0020 0000 - 0x0020 7FFF Internal ROM (32 kB)

0x0040 0000 - 0x0040 FFFF Internal RAM (64 kB)

(other addresses) Software can map other internal and external

memory into this area, to improve its effective

access time.

0x1000 0000 to

0x1FFF FFFF Internal Memory 0x1040 0000 - 0x104F FFFF Flash (1 MB)

0x2000 0000 to

0x5FFF FFFF External Memory 0x2000 0000 - 0x201F FFFF and

0x4000 0000 - 0x401F FFFF Static memory bank 0, 2 MB, STCS0

0x2400 0000 - 0x241F FFFF and

0x4400 0000 - 0x441F FFFF Static memory bank 1, 2 MB, STCS1

0x2800 0000 - 0x281F FFFF and

0x4800 0000 - 0x481F FFFF Static memory bank 2, 2 MB, STCS2

0x3000 0000-0x33FF FFFFand

0x5000 0000 - 0x53FF FFFF Dynamic memory bank 0, 64 MB

0x8000 0000 to

0x8FFF FFFF Peripherals See Table 2–2 Includes AHB Peripherals and 4 APBs

User manual Rev. 02 — 1 June 2007 8 of 362

NXP Semiconductors UM10208

Chapter 2: LPC2800 Memory mapping

Fig 2. Memory map

remapped area

0x0000 0000

0.0 GB

2.0 GB

4.0 GB

0x0FFF FFFF

0x2000 0000

0x8000 0000

0x7FFF FFFF

0x1FFF FFFF

0xFFFF FFFF

0x1000 0000

internal memory

external memory

(first instance)

peripherals

static memory bank 2, 2 MB 0x2800 0000 to 0x281F FFFF

reserved 0x2420 0000 to 0x27FF FFFF

dynamic memory bank 0, 64 MB 0x3000 0000 to 0x33FF FFFF

exception vectors 0x0000 0000 to 0x0000 001F

static memory bank 1, 2 MB 0x2400 0000 to 0x241F FFFF

static memory bank 0, 2 MB 0x2000 0000 to 0x201F FFFF

reserved 0x1050 0000 to 0x1FFF FFFF

internal ROM (32 kB) 0x0020 0000 to 0x0020 7FFF

reserved 0x0050 0000 to 0x0FFF FFFF

internal RAM (64 kB) 0x0040 0000 to 0x0040 FFFF

reserved 0x2020 0000 to 0x23FF FFFF

internal flash (1 MB) 0x1040 0000 to 0x104F FFFF

reserved 0x1000 0000 to 0x0000 003F

reserved 0x2820 0000 to 0x2FFF FFFF

reserved 0x3400 0000 to 0x3FFF FFFF

static memory bank 2, 2 MB 0x4800 0000 to 0x481F FFFF

reserved 0x4420 0000 to 0x47FF FFFF

dynamic memory bank 0, 64 MB 0x5000 0000 to 0x53FF FFFF

static memory bank 1, 2 MB 0x4400 0000 to 0x441F FFFF

static memory bank 0, 2 MB 0x4000 0000 to 0x401F FFFF

reserved 0x4020 0000 to 0x43FF FFFF

reserved 0x4820 0000 to 0x4FFF FFFF

reserved 0x5400 0000 to 0x7FFF FFFF

0x4000 0000

0x3FFF FFFF

0x9000 0000

0x8FFF FFFF

external memory

(second instance)

1.0 GB

includes AHB and 4 APB buses 0x8000 0000 to 0x8FFF FFFF

reserved 0x9000 0000 to 0xFFFF FFFF

002aac240

User manual Rev. 02 — 1 June 2007 9 of 362

NXP Semiconductors UM10208

Chapter 2: LPC2800 Memory mapping

2. Peripheral addressing

Peripheral devices on the LPC288x are distributed among the ARM High-speed Bus

(AHB) and four ARM Peripheral Buses (APBs). The following table indicates which bus

each device is connected to. Addresses not shown in this table are not used.

Table 2. LPC288x Peripheral devices

Address allocation Bus Register addresses (inclusive) Peripheral device

0x8000 0000 - 0x8000 1FFF APB0 0x8000 0000 - 0x8000 1C00 Event Router

0x8000 2000 - 0x8000 23FF APB0 0x8000 2000 - 0x8002 027C Real Time Clock (RTC)

0x8000 2400 - 0x8000 27FF APB0 0x8000 2400 - 0x8000 2430 10 bit Analog to Digital Converter (ADC)

0x8000 2800 - 0x8000 2BFF APB0 0x8000 2800 - 0x8000 283C Watchdog Timer (WDT)

0x8000 3000 - 0x8000 3FFF APB0 0x8000 3000 - 0x8000 31E8 I/O Configuration (IOCONF)

0x8000 4000 - 0x8000 4BFF APB0 0x8000 4000 - 0x8000 443C Clock Generation Unit (CGU) Switchbox

0x8000 4C00 - 0x8000 4FFF APB0 0x8000 4C00 - 0x8000 4CFC Clock Generation Unit (CGU)

0x8000 5000 - 0x8000 53FF APB0 0x8000 5000 - 0x8000 507C System Configuration Registers

0x8000 8000 - 0x8000 8FFF AHB 0x8000 8000 - 0x8000 8258 External Memory Controller (EMC)

0x8002 0000 - 0x8000 03FF APB1 0x8002 0000 - 0x8002 0010 Timer 0

0x8002 0400 - 0x8000 07FF APB1 0x8002 0400 - 0x8002 0410 Timer 1

0x8002 0800 - 0x8002 0BFF APB1 0x8002 0800 - 0x8002 082C I2C Controller

0x8004 0000 - 0x8004 1FFF AHB 0x8004 0000 - 0x8004 10B4 USB Controller

0x8010 0000 - 0x8010 0FFF APB2 0x8010 0000 - 0x8010 00BC Secure Digital / Multimedia Card

Interface (SD/MCI)

0x8010 1000 - 0x8010 1FFF APB2 0x8010 1000 - 0x8010 1034

0x8010 1FD4 - 0x8010 1FEC UART

0x8010 2000 - 0x8010 2FFF APB2 0x8010 2000 - 0x8010 201C

0x8010 2FD8 - 0x8010 2FEC Flash Programming Interface

0x8010 3000 - 0x8010 33FF APB2 0x8010 3000 - 0x8010 3080 LCD Interface

0x8010 3800 - 0x8010 3FFF APB2 0x8010 3800 - 0x8010 38FC

0x8010 3A00 - 0x8010 3A7C

0x8010 3C00 - 0x8010 3C10

GPDMA Controllers

0x8010 4000 - 0x8010 40FF APB2 0x8010 4000 - 0x8010 4058 ARM7 cache control

0x8020 0000 - 0x8020 007F APB3 0x8020 0000 - 0x8020 0078 Streaming Analog Input 1 (SAI1)

0x8020 0180 - 0x8020 01FF APB3 0x8020 0180 - 0x8020 01F8 Streaming Analog Input 4 (SAI4)

0x8020 0200 - 0x8020 027F APB3 0x8020 0200 - 0x8020 027C Streaming Analog Output 1 (SAO1)

0x8020 0280 - 0x8020 028F APB3 0x8020 0280 - 0x8020 02FC Streaming Analog Output 2 (SAO2)

0x8020 0380 - 0x8020 03FF APB3 0x8020 0380 - 0x8020 03BC I2S and Streaming Analog Converters

0x8030 0000 - 0x8030 0FFF AHB 0x8030 0000 - 0x8030 0474 Interrupt Controller

User manual Rev. 02 — 1 June 2007 10 of 362

1. Introduction

Upon reset, the LPC288x executes code from an internal ROM. This code allows four

possible types of startup. These are:

•Execute code from internal flash memory.

•Execute code from external memory bank 0.

•Download code from USB to memory.

•Test mode. Toggles a port pin to indicate basic device functionality.

2. Operation

Internal pulldowns on the P2.3 and P2.2 pins cause them to read as 0 when unconnected.

This results in the default startup mode being execution from internal Flash memory. One

or two external pullup resistors can cause startup to use one of the other modes, as

shown in Table 3–3.

3. Boot mode descriptions

The boot process is illustrated in figure 1. The following discussion describes each boot

mode in more detail.

Mode 0: Execute user program from internal flash memory

This is the default mode if the P2.3 and P2.2 pins are left unconnected. The Flash

memory begins at address 0x1040_0000. This is the address branched to in this mode.

In order to prevent accidental execution of an unprogrammed Flash, the ROM code

checks for a specific valid user program marker value in memory prior to branching into

the Flash memory. This marker is stored as address 0x104F_F800, 2K bytes below the

top of the 1MB Flash memory. The value expected here is 0xAA55_AA55. If Mode 0 is

selected and the valid user program marker value is not found in the Flash, control is

transferred to Mode 2 (USB download mode).

UM10208

Chapter 3: Boot process

Rev. 02 — 1 June 2007 User manual

Table 3. Boot flow chart

P2.3/Mode2 P2.2/Mode1 Mode selected

0 0 Execute user program from internal flash memory.

0 1 Execute user program from external memory on bank 0.

1 0 Download program from USB port to memory.

1 1 Test mode.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NXP Semiconductors Microcontrôleur

NXP Semiconductors

NXP Semiconductors UG10068 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors TWR-KL25Z Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S32R372141EVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MC9S08QL8 MCU Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors IOTZTB-DK006 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S12ZVML-MINIKIT Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MKL27Z128VFM4 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors KE1xF Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC1549 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors TWR-K21F120M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MPC5746R Mode d’emploi

NXP Semiconductors

NXP Semiconductors S12ZVMAEVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MC9S08SU16 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC11E Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QN9020 mini DK Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MPC5746R Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MC68HC16Z1 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC43 Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors i.MX 8M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC553 Series Mode d’emploi

NXP Semiconductors

NXP Semiconductors TWR-KM34Z50M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM10741 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MPC5748G Low Cost EVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors KITMPXA6115AEVB Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur