NXP Semiconductors TWR-K70F120M Instructions d'utilisation et d'entretien

Quick Start Guide

TWR-K70F120M

High-Performance MCUs with Graphics

LCD, Connectivity and Security

TOWER SYSTEM

Quick Start Guide

Get to Know the TWR-K70F120M

Primary

Connector

Infra-Red

General Purpose

Tower Plug-In

(TWRPI) Socket

SW3 (Reset)

Power/OSJTAG

Mini-B USB

Connector

Secondary

Connector

SW1

SW2

Touch TWRPI

Socket

LED/Touch

Buttons

E1–E4

MK70FN1M0VMJ12

Microcontroller

MMA8451

Accelerometer

1 Gb 16-bit wide

LPDDR2 Memory

Figure 1: Front side of TWR-K70F120M module (TWRPI devices not shown).

Figure 2: Back side of TWR-K70F120M module.

TOWER SYSTEM

TWR-K70F120M

Freescale Tower System

The TWR-K70F120M module is part of the Freescale Tower System, a modular

development platform that enables rapid prototyping and tool re-use through

reconfigurable hardware. The TWR-K70F120M can be used with a broad

selection of Tower System peripheral modules, including the new TWR-LCD-RGB

which accepts RGB data from the K70 MCU graphics LCD controller.

Potentiometer

MC9S08JM60

OSJTAG Circuit

Figure 2: Back side of TWR-K70F120M module.

SD Card

Socket

VBAT (RTC)

Battery

Holder

2 Gb NAND

Flash

Quick Start Guide

TWR-K70F120M Features

• MK70FN1M0VMJ12 MCU (120 MHz, 1 MB flash, graphics

LCD, Ethernet, USB OTG, tamper detection, encryption, NAND

flash and DDR controller, 256 MBGA)

• Interfaces to the new TWR-LCD-RGB Tower peripheral module

(accepts RGB data directly from the K70 MCU LCD controller)

• MC9S08JM60 open source JTAG (OSJTAG) circuit

• Micron MT47H64M16HR-25 1 Gb 16-bit wide LPDDR2 memory

• Micron MT29F2G16ABAEAWP 2 Gb NAND flash

• Four user-controlled status LEDs

• Four capacitive touch pads and two mechanical push buttons

• General-purpose TWRPI socket (Tower plug-in module)

• TWRPI-TOUCH-STR socket (touch-sensing Tower

plug-in module)

TOWER SYSTEM

Step-by-Step Installation Instructions

Install the

Software and Tools

Install the P&E Micro Kinetis Tower

toolkit. The toolkit includes the

OSJTAG and USB to serial drivers.

These can be found on the DVD

under Software.

Configure the

Hardware

Install the included battery into the

VBAT (RTC) battery holder. Then,

connect one end of the USB cable

to the PC and the other end to the

Power/OSJTAG mini-B connector

on the TWR-K70F120M module.

Allow the PC to automatically

configure the USB drivers if needed.

Tilt the

Board

Tilt the board side to side to see

the LEDs on E1–E4 light up as it is

tilted. While the board is held flat,

touch the pads on E1–E4 to

toggle the LEDs.

Play the

Memory Game

Press SW2 to play a memory recall

game using the touch pads E1–E4.

A sequence will light up, then press

the touch pads in the order flashed.

If an incorrect sequence is touched

or too much time has elapsed, all

the lights will blink rapidly and the

game will reset.

Press SW1 to return to the

accelerometer demo.

TWR-K70F120M Features

Quick Start Guide

TWR-K70F120M Jumper Options

The following is a list of all jumper options. The default installed jumper settings are

shown in white text within the red boxes.

Download the TWR-

K70F120M User Manual

and Demonstration Labs

Download the TWR-K70120M user

manual and demonstration labs at

freescale.com/TWR-K70F120M.

Jumper Option Setting Description

J8 MCU Power Connection ON Connect on-board 3.3-volt supply to MCU

OFF Isolate MCU from power

(connect an ammeter to measure current)

J20 MCU VDD_INT Power

Connection

ON Connect VDD and VDD_INT rails together

OFF Isolate MCU VDD_INT from power

(connect an ammeter to measure current)

J17 VBAT Power Selection 1-2 Connect VBAT to on-board 3.3-volt supply

2-3 Connect VBAT to the higher voltage between

on-board 3.3-volt supply or coin-cell supply

Download the Freescale

CodeWarrior IDE and

MQX™ RTOS

Download the Freescale

CodeWarrior IDE and MQX RTOS by

clicking on the relevant links on the

Software tab of the Tower Kit DVD.

TOWER SYSTEM

TWR-K70F120M Jumper Options (continued)

Jumper Option Setting Description

J8 MCU Power Connection ON Connect on-board 3.3-volt supply to MCU

OFF Isolate MCU from power

(connect an ammeter to measure current)

J20 MCU VDD_INT Power

Connection

ON Connect VDD and VDD_INT rails together

OFF Isolate MCU VDD_INT from power

(connect an ammeter to measure current)

J17 VBAT Power Selection 1-2 Connect VBAT to on-board 3.3-volt supply

2-3 Connect VBAT to the higher voltage between

on-board 3.3-volt supply or coin-cell supply

Jumper Option Setting Description

J18 Oscillator output enable OFF 50 MHz oscillator output enabled

ON 50 MHz oscillator output disabled

J10 OSJTAG Bootloader

Selection

ON OSJTAG bootloader mode

(OSJTAG ﬁrmware reprogramming)

OFF Debugger mode

J19 50 MHz Oscillator

Power

ON ON = on-board 50 MHz oscillator powered

OFF OFF = on-board 50 MHz oscillator not powered*

J12 JTAG Board Power

Connection

ON Connect on-board 5-volt supply to JTAG port

(supports powering board from JTAG pod

supporting 5-volt supply output)

OFF Disconnect on-board 5-volt supply to JTAG port

J2 IR Transmitter

Connection

ON Connect PTD7/CMT_IRO to IR transmitter (D1)

OFF Disconnect PTD7/CMT_IRO from IR transmitter (D1)

J16 IR Receiver Connection ON Connect DAC1_OUT/CMP2_IN3 to IR receiver

OFF Disconnect DAC1_OUT/CMP2_IN3 from IR receiver

J1 VREGIN Power

Connection

ON Connect USB0_VBUS from elevator to VREGIN

OFF Disconnect USB0_VBUS from elevator to VREGIN

*NOTE: This option must be selected whenever a Tower System module card that provides a clock on primary

elevator pin B24 is connected to the CPU module.

For more information, visit freescale.com/Tower

Join the online Tower community at towergeeks.org

Freescale, the Freescale logo and CodeWarrior are trademarks of

Freescale semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product

or service names are the property of their respective owners.

Doc Number: TWRK70F120MQSG REV 1

Agile Number: 926-78651 REV B

Visit freescale.com/TWR-K70F120M,

freescale.com/K70 or freescale.com/Kinetis

for information on the TWR-K70F120M module,

including:

• TWR-K70F120M user guide

• TWR-K70F120M schematics

• Tower System fact sheet

Support

Visit freescale.com/support for a list of phone

numbers within your region.

Warranty

Visit freescale.com/warranty for complete

warranty information.

Quick Start GuideQuick Start Guide

Autres manuels pour TWR-K70F120M

Table des matières

Autres manuels NXP Semiconductors Microcontrôleur

NXP Semiconductors

NXP Semiconductors USB-KW38 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM2NTA5KIT Manuel utilisateur

NXP Semiconductors

NXP Semiconductors PN7462 series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors IOTZTB-DK006 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QN9090-DK006 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UG10068 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM11483 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QN9020 mini DK Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MPC5748G Low Cost EVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S12ZVML-MINIKIT Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM11527 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors Freescale K22 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC1102 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors TWR-K21F120M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC11U3x Manuel utilisateur

NXP Semiconductors

NXP Semiconductors A71CLARD-BA Manuel utilisateur

NXP Semiconductors

NXP Semiconductors Freescale TWR-MECH Manuel utilisateur

NXP Semiconductors

NXP Semiconductors i.MX31 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors Freescale 56800TDC Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MTRCKTSPS5744P Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC5411 Series Manuel d'exploitation

NXP Semiconductors

NXP Semiconductors UM108 Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors NTAG I2C plus Manuel d'utilisation et d'entretien

NXP Semiconductors

NXP Semiconductors S32G-VNP-GLDBOX Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur