NXP Semiconductors IOTZTB-DK006 Manuel utilisateur

UM11393

IOTZTB-DK006 Development Kit User Guide

Rev.3.0 —9 March 2021

Document information

Info

Content

Keywords

IOTZTB DK, User Guide

Abstract

This document is a user guide for the IOTZTB Development Kit

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM1393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

2 of 23

Contact information

For more information, please visit: http://www.nxp.com

Revision history

Rev

Date

Description

1V0

20200420

Initial release

2V0

20200914

Second version

3V0

20210309

Third version –Added support for K32W041AM and K32W041A

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

3 of 23

1. Introduction

IOTZTB-DK006 is designed for evaluation and development of K32W061, K32W041AM,

K32W041A and JN5189 devices to conveniently evaluate the devices functions and

performance. There are also some useful peripherals, like GPIOs, and Arduino interface.

J-Link and J-Trace functions are all supported for debugging the devices. ISP download

function is also contained and very easy to use.

1.1 Purpose

This document introduces all functions of IOTZTB-DK006 and describes all parts of

IOTZTB-DK006 boards in detail.

1.2 Kit contents

IOTZTB-DK006 includes the following boards:

•Carrier Main Board (3)

•K32W061 upgrade module board (3)

•JN5189 upgrade module Board (3)

•K32W061 USB Dongle

•Generic expansion board

•Lighting expansion board

•Not included in the Kit, sold separately: K32W041A and K32W041AM upgrade

module boards

Figure 1 Board overview

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

4 of 23

2. Carrier Main Board

The OM15076 also called DK6 carrier main board provides a flexible development

system for NXP’s K32W061, K32W041, K32W041AM, K32W041A and JN5189/88(T)

ultra-low power, high performance wireless microcontrollers. It can be used with a wide

range of development tools, including NXP’s MCUXpresso IDE. It has been developed

by NXP to enable evaluation and prototyping with the JN518x and K32W0x IEEE

802.15.4 and Bluetooth LE 5.0 wireless microcontrollers.

The three carrier boards supplied in the development kit are physically identical. They

are all pre-fitted with an Arduino-compatible expansion board and a K32W061/041-based

module board with integrated antenna.

2.1 Feature summary

The carrier main board includes the following features:

•K32W061/041 upgrade module site

•NFC Tag with printed antenna

•On-board, high-speed USB based, Link2 debug probe with ARM’s CMSIS-DAP

and SEGGER J-Link protocol options.

•Link2 probe can be used with on-board K32W061/041 or external target.

•Support for external debug probes.

•Power, Reset, ISP and UART Tx/Rx LEDs.

•Target Reset, and User buttons.

•Expansion options based on Arduino R3, plus additional expansion port pins.

•On-board 3.3V from USB port, 4xAAA batteries, 2xAAA batteries (low-power

mode) or external power supply options.

Figure 2 Carrier Main Board

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

5 of 23

•Built-in power consumption measurement.

•UART, I2C and SPI port bridging from LPC4233 target to USB via the on-board

debug probe.

•8MB Macronix MX25R QSPI flash.

•FTDI USB connector.

2.2 Board layout and settings

This section provides a quick reference guide to the main board components,

configurable items, visual indicators and expansion connectors. The layout of the

components on the OM15076 Carrier Main Board is shown in Figure 3.

The function of each identified component is listed in Table 1

Table 1. Table Board interface components

Circuit ref

Description

Link2 LPC4322 BOOT0_LED indicator. Reflects the state of LPC43xx Link2 MCU

P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60 seconds.

After 60 seconds, the LPC4322 is reset.

DS1

K32W061/041 Power LED

DS2,

DS3

2x Red debug LEDs connected respectively to K32W061/041 PIO_0 (DS2) and

PIO_3 (DS3). LEDs are on anytime the PIO is low.

DS4

K32W061/041 Reset LED –LED is on anytime the Target RESET is pulled low.

DS5,

DS6

Green LEDs connected respectively to UART0_Tx (DS5) and UART0_Rx (DS6).

DS8

In System Programming (ISP) LED indicator. LED is ON when SW2 button is

pressed.

IC2

Link2 MCU

Figure 3 Carrier board layout

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

6 of 23

FTDI serial header. In addition to provide a serial output from K32W061/041, the

Target side of the board can be powered from the FTDI header. The

K32W061/041 supports serial ISP boot from the FTDI header.

32 pins Expansion header connector for debug. All the K32W061/41/041 IOs from

modules and more are available here.

J14

K32W061/041 VBAT current monitor V sense measurement. The V sense can be

measured with a volt meter. Pin 1 (square pad) is positive and pin 2 is negative.

K32W061/041 current is calculated by dividing the measured voltage at J14 by the

V sense resistance value of 3.3Ω.

J15

Link2 mini USB B-type connector. Powers both the Link2 side of the board and

depending on the JP3, J5 configuration, the K32W061/041 Target side of the

board. Power the board from this connector when using the on-board debug probe

to debug the K32W061/041 Target MCU.

JP1

K32W061/041 Target SWD disable –2-position jumper pins.

1. Jumper “ON” (default) the K32W061/041 Target SWD interface enabled.

Normal operating mode where the Target SWD is connected to either the

on-board

2. Link2 debug probe or an external debug probe. Jumper “OFF”, the

K32W061/041 Target SWD interface is disabled. Use this setting only

when the on-board Link2 debug probe is used to debug an off-board

Target K32W061/041.

JP2

SWD interface buffer power selection

JP3

K32W061/041 power source selection

1. Jumper fitted in position pin 1 - 2 (default -5V REG). Power source is

either 5V from mini USB connector or FTDI connector, or 4.5V from

3xAAA batteries or 5V from a 7-12V DC power supply connected on J4.

2. Jumper fitted in position pin 2 - 3 (BAT 6V). Power source is 4xAAA

batteries.

See details on Board power diagram Figure 5

JP4

Jumper to route LPC or FTDI to UART RX0 K32W061/041 (to change in pair with

JP7)

JP5

Link2 (LPC4322) force DFU boot –2 position jumper pins.

1. Jumper open (default) or shunted to boot mode for Link2 to follow the

normal boot sequence. The Link2 will boot from internal flash if image is

found there. With the internal flash erased the Link2 normal boot

sequence will fall through to DFU boot.

2. Jumper shunted to force the Link2 to DFU boot mode. Use this setting to

reprogram the Link2 internal flash with a new image or to use the

MCUXpresso IDE with CMSIS-DAP protocol.

JP6

JP6 is used to isolate the Link2 debug probe (SPI bridge function) from the

K32W061/041 target to prevent leakage current in power critical applications /

current consumption analysis. JP6 needs to be fitted in position 1 - 2 to use the

SPI bridging function between the K32W061/041 and Link2. This jumper is not

fitted by default

JP7

Jumper to shunt LPC to K32W061/041 or FTDI to UART TX0 K32W061/041 (to

change in pair with JP4)

CN1,

CN2,

CN3,

CN4

Expansion connectors, including Arduino Uno rev3 compatible connectivity.

JM1,

JM2

K32W061/041 module headers

10-pin SWD connector –The SWD connector is used to debug the K32W061/041

Target from an external debug probe. The same SWD connector can also be used

to connect the on-board Link2 debug probe to an off-board target MCU (for this

JP1 must be shunted).

BP1

User Interface button connected to IO1. Used in some Applications Notes.

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

7 of 23

SW2

In System Programming (ISP) button. K32W061/041 will enter ISP mode when

SW2 is pressed during hardware reset.

SW4

K32W061/041 Reset pushbutton.

To ease the board usage and any debug the connectors serigraphy is also copied on PCB bottom.

J7, J13, J12 & J11 battery slots are also here.

2.3 LED indicators

The DK6 board LED location are shown in Figure 3. A description of each on-board LED

indicator is shown in next table.

Table 2. LED indicator functions

LED reference

Description

Link2 MCU BOOT0_LED indicator. Reflects the state of Link2 MCU

P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60

seconds. After 60 seconds, the Link2 MCU is reset. It will be ON when

the Link2 MCU is Booting using DFU (See description for JP5).

DS1

K32W061/041 Power LED. This LED is on any time power is applied to

the K32W061/041 wireless MCU.

DS2, DS3

2x Red debug LEDs connected respectively to K32W061/041 PIO_0

(DS2) and PIO_3 (DS3). LEDs are on anytime the respective PIOs from

the K32W061/041 are pulled low.

DS4

K32W061/041 Reset LED –LED is on anytime the Target RESET is

pulled low.

DS5, DS6

2x Green LEDs connected respectively to UART0_Tx (DS5) and

UART0_Rx (DS6). LEDs will flash any time there is activity on the

UART0.

DS8

In System Programming (ISP) LED indicator. LED is ON when IO5_ISP

is pulled low and when SW2 button is pressed.

Figure 4 OM15076 DK6 PCB bottom view

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

8 of 23

2.4 ARDUINO connectors

ARDUINO compatible connectors are based on Arduino R3.

References on the DK6 board are CN1, CN2, CN3, CN4.

The Generic expansion board OM15082 can be plugged into these connectors.

2.5 Buttons

2.5.1 Reset button

This button (SW4) is used to reset the K32W061/041 (note that the Link2 is NOT reset by

this button)

2.5.2 ISP button

This button connects the K32W061/041_PIO5 (ISP_Entry) pin to ground. This should be

used to set the K32W061/041 in ISP mode to program a binary file into the chip memory.

To force entry into this ISP mode, hold down the ISP button (SW2), press and release

the Reset button (SW4), then release the ISP button (SW2). This is done automatically

when using the DK6 Production Flash programmer with J2 (FTDI USB interface).

2.6 User Interface button

This button (BP1) is connected to K32W061/041_PIO_1 and should be used as an input.

2.7 K32W061/041 Serial port

The K32W061/041 UART0 can also be connected through a virtual communication port

(VCOM) UART bridge Link2 function either to a host computer connected to the J2 USB

FTDI or to J15 USB Link2. By default, the DK 6 is configured to use the FTDI USB.

For Link2 USB: The factory default CMSIS-DAP Link2 image includes UART bridge

functionality (VCOM support), and this firmware is also available with the LPCScrypt

utility, available at https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES power connections and measurements.

For the USB FTDI, the PC driver is available on FTDI website (the FTDI chip is already

configured before the carrier board release).

2.8 Board power connections

A block diagram of the board power tree is shown in Figure 5. When the K32W061/041

Target is to be debugged from the on board Link2 probe, the USB mini B-type connector

(J15) must connected to a Host computer. When the K32W061/041 Target is to be

debugged from an external debug probe, instead of the on-board debug probe, the Link

USB connector (J15) must be disconnected.

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

9 of 23

The K32W061/041 Target VBAT selection is made at JP3, J5, with 3.3V from on-board

LDO set as the default.

2.9 Debug Configurations

The DK6 board has a built-in debug probe referred to as “Link2”. The K32W061/041

target wireless MCU can be debugged by the Link2 debugging probe, or from an external

debug probe installed at P1. On-board jumpers JP1 and JP2 must be correctly positioned

for each mode. The on-board Link2 debug probe is capable of debugging target MCU’s

with a VDDIO range of 1.6V to 3.6V. Check the sections below for the appropriate jumper

settings and how to properly power the board.

2.9.1 Debug using on-board debug probe

To use the on-board Link debug probe:

•The jumper JP2 must be fitted in position pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted in position 2 –3 to enable the target

K32W061/041.

•Connecting the mini USB J15 to a host computer will power the Link and

according JP3, JP5 position, the K32W061/041 sections of the board and

provide the USB link to the debug tool software.

2.9.2 Debug using external debug probe

To use an external debug probe:

•connect the probe to the SWD (P1) connector

•power the K32W061/041 Target section of the board from the FTDI header

(J1) or the Jack connector (J4)

•and fit a jumper to JP2 across pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted across pin 2 –3 to enable the target

Figure 5 Board power diagram

NXP Semiconductors

IOTZTB-DK006

IOTZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.3.0 —9 March 2021

10 of 23

K32W061/041.

•The on-board Link2 debug probe must be unpowered, by leaving USB mini

(J15) unconnected.

2.9.3 On-Board Link2 flash programming

To program the Link2 Flash the Link2 MCU must be in DFU mode. If the Link2 already

has a valid image in the flash, you will need to force it into DFU mode by placing a

jumper shunt on JP5 across pin 1 - 2, then power the board by connecting the mini USB

J15 to a host computer. Link2 MCU programming is performed using the LPCScrypt

utility (see https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES). Instructions for using the tool are located at the

same web page.

2.9.4 Using the DK6 to debug an off-board target

The DK6 board’s Link2 debug probe may be used to debug an off-board target MCU.

The on-board Link2 debug probe is capable of debugging target MCU’s with a VDDIO

range of 1.6V to 3.6V. To keep the on-board target K32W061/041 MCU from interfering

with the SWD interface:

•JP1 must be fitted across pin 1 - 2.

•The Link2 debug probe SWD is connected by a ribbon cable between the

P1 connector to the off-board target MCU SWD interface.

•Power the DK6 board from the Link USB connector J15,

•Fit jumper JP2 across pins 2 - 3 (External Target).

Table des matières

Autres manuels NXP Semiconductors Microcontrôleur

NXP Semiconductors

NXP Semiconductors S12VR32EVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors WB10-AT i.MX 8M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM10574 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors Freescale MC9S12XE Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UG10068 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors WPR1500-BUCK Manuel utilisateur

NXP Semiconductors

NXP Semiconductors PN7462 series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S32R27 Mode d’emploi

NXP Semiconductors

NXP Semiconductors A71CLARD-BA Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC29 Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors Freescale DEMOEM MCF51EM Instructions de fonctionnement

NXP Semiconductors

NXP Semiconductors KE17Z Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM2385 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors KE1xF Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MKL04Z8VFK4 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LEC-IMX8MM Manuel utilisateur

NXP Semiconductors

NXP Semiconductors M53015EVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S32G-VNP-GLDBOX Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC-Link2 Guide de démarrage rapide

NXP Semiconductors

NXP Semiconductors LPC1769 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors HCS12 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC824M201JHI33 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QN908 series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM5578 PN7150 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur