NXP Semiconductors IoT ZTB-DK006 Manuel utilisateur

UM11393

IoT_ZTB-DK006 Development Kit User Guide

Rev.1.0 —20 April 2020

Document information

Info

Content

Keywords

IoT_ZTB DK, User Guide

Abstract

This document is a user guide for the IoT_ZTB Development Kit

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM1393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

2 of 21

Contact information

For more information, please visit: http://www.nxp.com

Revision history

Rev

Date

Description

1V0

20200420

Initial release

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

3 of 21

1. Introduction

IoT_ZTB is designed for evaluation and development of K32W061 and JN5189 devices

to conveniently evaluate the devices functions and performance. There are also some

useful peripherals, like GPIOs, and Arduino interface. J-Link and J-Trace functions are all

supported for debugging the devices. ISP download function is also contained and very

easy to use.

1.1 Purpose

This document introduces all functions of IoT_ZTB DK. Descripts all parts of IoT_ZTB DK

boards in detail.

1.2 Kit contents

IoT_ZTB DK includes the following three boards:

•Carrier Main Board

•K32W061 Module board

•JN5189 Module Board

•K32W061 USB Dongle

•Generic expansion board

•Lighting expansion board

Figure 1 Board overview

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

4 of 21

2. Carrier Main Board

The OM15076 also called DK6 carrier main board provides a flexible development

system for NXP’s K32W061 and JN5189 ultra-low power, high performance wireless

microcontrollers. It can be used with a wide range of development tools, including NXP’s

MCUXpresso IDE. It has been developed by NXP to enable evaluation and prototyping

with the K32W061/041 IEEE 802.15.4 and BLE 5.0 wireless microcontroller.

The carrier boards (part number: OM15076) supplied in the development kit are

physically identical. They are all pre-fitted with an Arduino-compatible expansion board

and a K32W061-based module with integrated antenna.

2.1 Feature summary

The carrier main board includes the following features:

•K32W061 module site

•NFC Tag with printed antenna

•On-board, high-speed USB based, Link2 debug probe with ARM’s CMSIS-DAP

and SEGGER J-Link protocol options.

•Link2 probe can be used with on-board K32W061 or external target.

•Support for external debug probes.

•Power, Reset, ISP and UART Tx/Rx LEDs.

Figure 2 Carrier Main Board

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

5 of 21

•Target Reset, and User buttons.

•Expansion options based on Arduino R3, plus additional expansion port pins.

•On-board 3.3V from USB port, 4xAAA batteries, 2xAAA batteries (low-power

mode) or external power supply options.

•Built-in power consumption measurement.

•UART, I2C and SPI port bridging from LPC4233 target to USB via the on-board

debug probe.

•8Mb Macronix MX25R QSPI flash.

•FTDI USB connector.

2.2 Board layout and settings

This section provides a quick reference guide to the main board components,

configurable items, visual indicators and expansion connectors. The layout of the

components on the OM15076 Carrier Main Board is shown in Figure 3.

The function of each identified component is listed in Table 1

Table 1. Table Board interface components

Circuit ref

Description

Link2 LPC4322 BOOT0_LED indicator. Reflects the state of LPC43xx Link2

MCU P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60

seconds. After 60 seconds, the LPC4322 is reset.

DS1

K32W061 Power LED

DS2, DS3

2x Red debug LEDs connected respectively to K32W061 PIO_0 (DS2) and

PIO_3 (DS3). LEDs are on anytime the PIO is low.

DS4

K32W061 Reset LED –LED is on anytime the Target RESET is pulled low.

Figure 3 Carrier board layout

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

6 of 21

DS5, DS6

Green LEDs connected respectively to UART0_Tx (DS5) and UART0_Rx

(DS6).

DS8

In System Programming (ISP) LED indicator. LED is ON when SW2 button is

pressed.

IC2

Link2 MCU

FTDI serial header. In addition to provide a serial output from K32W061, the

Target side of the board can be powered from the FTDI header. The

K32W061 supports serial ISP boot from the FTDI header.

32 pins Expansion header connector for debug. All the K32W061 IOs from

modules and more are available here.

J14

K32W061 VBAT current monitor V sense measurement. The V sense can be

measured with a volt meter. Pin 1 (square pad) is positive and pin 2 is

negative. K32W061 current is calculated by dividing the measured voltage at

J14 by the V sense resistance value of 3.3Ω.

J15

Link2 mini USB B-type connector. Powers both the Link2 side of the board

and depending on the JP3, J5 configuration, the K32W061 Target side of the

board. Power the board from this connector when using the on-board debug

probe to debug the K32W061 Target MCU.

K32W061 Target SWD disable –2-position jumper pins.

1. Jumper “ON” (default) the K32W061 Target SWD interface enabled.

Normal operating mode where the Target SWD is connected to

either the on-board

2. Link2 debug probe or an external debug probe. Jumper “OFF”, the

K32W061 Target SWD interface is disabled. Use this setting only

when the on-board Link2 debug probe is used to debug an off-board

Target K32W061.

SWD interface buffer power selection

K32W061 power source selection

1. Jumper fitted in position pin 1 - 2 (default -5V REG). Power source

is either 5V from mini USB connector or FTDI connector, or 4.5V

from 3xAAA batteries or 5V from a 7-12V DC power supply

connected on J4.

2. Jumper fitted in position pin 2 - 3 (BAT 6V). Power source is 4xAAA

batteries.

See details on Board power diagram Figure 5

Jumper to route LPC or FTDI to UART RX0 K32W061 (to change in pair with

JP7)

Link2 (LPC4322) force DFU boot –2 position jumper pins.

1. Jumper open (default) or shunted to boot mode for Link2 to follow

the normal boot sequence. The Link2 will boot from internal flash if

image is found there. With the internal flash erased the Link2 normal

boot sequence will fall through to DFU boot.

2. Jumper shunted to force the Link2 to DFU boot mode. Use this

setting to reprogram the Link2 internal flash with a new image or to

use the MCUXpresso IDE with CMSIS-DAP protocol.

JP6 is used to isolate the Link2 debug probe (SPI bridge function) from the

K32W061 target to prevent leakage current in power critical applications /

current consumption analysis. JP6 needs to be fitted in position 1 - 2 to use

the SPI bridging function between the K32W061 and Link2. This jumper is

not fitted by default

Jumper to shunt LPC to K32W061 or FTDI to UART TX0 K32W061 (to

change in pair with JP4)

CN1, CN2,

CN3, CN4

Expansion connectors, including Arduino Uno rev3 compatible connectivity.

JM1, JM2

K32W061 module headers

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

7 of 21

10-pin SWD connector –The SWD connector is used to debug the K32W061

Target from an external debug probe. The same SWD connector can also be

used to connect the on-board Link2 debug probe to an off-board target MCU

(for this JP1 must be shunted).

BP1

User Interface button connected to IO1. Used in some Applications Notes.

SW2

In System Programming (ISP) button. K32W061 will enter ISP mode when

SW2 is pressed during hardware reset.

SW4

K32W061 Reset pushbutton.

To ease the board usage and any debug the connectors serigraphy is also copied on PCB bottom.

J7, J13, J12 & J11 battery slots are also here.

2.3 LED indicators

The DK6 board LED location are shown in Figure 3. A description of each on-board LED

indicator is shown in next table.

Table 2. LED indicator functions

LED reference

Description

Link2 MCU BOOT0_LED indicator. Reflects the state of Link2 MCU

P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60

seconds. After 60 seconds, the Link2 MCU is reset. It will be ON when

the Link2 MCU is Booting using DFU (See description for JP5).

DS1

K32W061 Power LED. This LED is on any time power is applied to the

K32W061 wireless MCU.

DS2, DS3

2x Red debug LEDs connected respectively to K32W061 PIO_0 (DS2)

and PIO_3 (DS3). LEDs are on anytime the respective PIOs from the

K32W061 are pulled low.

DS4

K32W061 Reset LED –LED is on anytime the Target RESET is pulled

Figure 4 OM15076 DK6 PCB bottom view

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

8 of 21

low.

DS5, DS6

2x Green LEDs connected respectively to UART0_Tx (DS5) and

UART0_Rx (DS6). LEDs will flash any time there is activity on the

UART0.

DS8

In System Programming (ISP) LED indicator. LED is ON when IO5_ISP

is pulled low and when SW2 button is pressed.

2.4 ARDUINO connectors

ARDUINO compatible connectors are based on Arduino R3.

References on the DK6 board are CN1, CN2, CN3, CN4.

The Generic expansion board OM15082 can be plugged into these connectors.

2.5 Buttons

2.5.1 Reset button

This button (SW4) is used to reset the K32W061 (note that the Link2 is NOT reset by this

button)

2.5.2 ISP button

This button connects the K32W061_PIO5 (ISP_Entry) pin to ground. This should be used

to set the K32W061 in ISP mode to program a binary file into the chip memory.

To force entry into this ISP mode, hold down the ISP button (SW2), press and release

the Reset button (SW4), then release the ISP button (SW2). This is done automatically

when using the DK6 Production Flash programmer with J2 (FTDI USB interface).

2.6 User Interface button

This button (BP1) is connected to K32W061_PIO_1 and should be used as an input.

2.7 K32W061 Serial port

The K32W061 UART0 can also be connected through a virtual communication port

(VCOM) UART bridge Link2 function either to a host computer connected to the J2 USB

FTDI or to J15 USB Link2. By default, the DK 6 is configured to use the FTDI USB.

For Link2 USB: The factory default CMSIS-DAP Link2 image includes UART bridge

functionality (VCOM support), and this firmware is also available with the LPCScrypt

utility, available at https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES power connections and measurements.

For the USB FTDI, the PC driver is available on FTDI website (the FTDI chip is already

configured before the carrier board release).

2.8 Board power connections

A block diagram of the board power tree is shown in Figure 5. When the K32W061

Target is to be debugged from the on board Link2 probe, the USB mini B-type connector

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

9 of 21

(J15) must connected to a Host computer. When the K32W061 Target is to be debugged

from an external debug probe, instead of the on-board debug probe, the Link USB

connector (J15) must be disconnected.

The K32W061 Target VBAT selection is made at JP3, J5, with 3.3V from on-board LDO

set as the default.

2.9 Debug Configurations

The DK6 board has a built-in debug probe referred to as “Link2”. The K32W061 target

wireless MCU can be debugged by the Link2 debugging probe, or from an external

debug probe installed at P1. On-board jumpers JP1 and JP2 must be correctly positioned

for each mode. The on-board Link2 debug probe is capable of debugging target MCU’s

with a VDDIO range of 1.6V to 3.6V. Check the sections below for the appropriate jumper

settings and how to properly power the board.

2.9.1 Debug using on-board debug probe

To use the on-board Link debug probe:

•The jumper JP2 must be fitted in position pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted in position 2 –3 to enable the target

K32W061.

•Connecting the mini USB J15 to a host computer will power the Link and

according JP3, J5 position, the K32W061 sections of the board and provide

the USB link to the debug tool software.

2.9.2 Debug using external debug probe

To use an external debug probe:

•connect the probe to the SWD (P1) connector

Figure 5 Board power diagram

NXP Semiconductors

IoT_ZTB

IoT_ZTB-DK006 Development Kit User Guide

UM11393

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —20 Apr 2020

10 of 21

•power the K32W061 Target section of the board from the FTDI header (J1)

or the Jack connector (J4)

•and fit a jumper to JP2 across pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted across pin 2 –3 to enable the target

K32W061.

•The on-board Link2 debug probe must be unpowered, by leaving USB mini

(J15) unconnected.

2.9.3 On-Board Link2 flash programming

To program the Link2 Flash the Link2 MCU must be in DFU mode. If the Link2 already

has a valid image in the flash, you will need to force it into DFU mode by placing a

jumper shunt on JP5 across pin 1 - 2, then power the board by connecting the mini USB

J15 to a host computer. Link2 MCU programming is performed using the LPCScrypt

utility (see https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES). Instructions for using the tool are located at the

same web page.

2.9.4 Using the DK6 to debug an off-board target

The DK6 board’s Link2 debug probe may be used to debug an off-board target MCU.

The on-board Link2 debug probe is capable of debugging target MCU’s with a VDDIO

range of 1.6V to 3.6V. To keep the on-board target K32W061 MCU from interfering with

the SWD interface:

•JP1 must be fitted across pin 1 - 2.

•The Link2 debug probe SWD is connected by a ribbon cable between the

P1 connector to the off-board target MCU SWD interface.

•Power the DK6 board from the Link USB connector J15,

•Fit jumper JP2 across pins 2 - 3 (External Target).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NXP Semiconductors Microcontrôleur

NXP Semiconductors

NXP Semiconductors KL25 Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MC9S12XS256 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MKL04Z8VFK4 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors P89LPC9321 UM10310 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC1549 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors SLN-VIZN3D-IOT Manuel utilisateur

NXP Semiconductors

NXP Semiconductors AN10815 Instructions d'installation et d'utilisation

NXP Semiconductors

NXP Semiconductors SLN-LOCAL2-IOT Manuel utilisateur

NXP Semiconductors

NXP Semiconductors freescale KV4 Series Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MRF300AN Manuel utilisateur

NXP Semiconductors

NXP Semiconductors AN11268 Guide de dépannage

NXP Semiconductors

NXP Semiconductors LPC1769 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MPC574xR Series Instructions d'installation et d'utilisation

NXP Semiconductors

NXP Semiconductors TWR-K60N512-IAR Manuel utilisateur

NXP Semiconductors

NXP Semiconductors TWR-K21F120M Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S32R274RRUEVB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors JN517x-DK005 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors A71CLARD-BA Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QN9020 mini DK Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM-SE051ARD Manuel utilisateur

NXP Semiconductors

NXP Semiconductors LPC55S0x Mode d’emploi

NXP Semiconductors

NXP Semiconductors NTAG I2C plus Manuel d'utilisation et d'entretien

NXP Semiconductors

NXP Semiconductors EdgeLock A5000 Instructions d'installation et d'utilisation

NXP Semiconductors

NXP Semiconductors MKL27Z128VFM4 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur