Nibe SMO 40 Guide de l'utilisateur

Installer manual

LEK

SMO 40

Control module

IHB GB 1546-3

231760

Quick guide

Navigation

Ok button (confirm/select)

Back button (back/undo/exit)

Control knob (move/increase/reduce)

A detailed explanation of the button functions can be found on page 34.

How to scroll through menus and make different settings is described on page 36.

Set the indoor climate

MY INSTALLATION

INDOOR CLIMATE HOT WATER

INFO

The mode for setting the indoor temperature is accessed by pressing the OK button twice, when in the start mode

in the main menu.

Increase hot water volume

1X INDOOR CLIMATE HOT WATER

MY INSTALLATION INFO

To temporarily increase the amount of hot water (if a hot water heater is installed to your SMO 40), first turn the

control knob to mark menu 2 (water droplet) and then press the OK button twice.

In event of disturbances in comfort

If a disturbance in comfort of any type occurs there are some measures that can be taken before you need to

contact your installer. See page 53 for instructions.

Table of Contents

41 Important information

4Safety information

72 Delivery and handling

7Mounting

7Supplied components

83 The Control Module Design

8Electrical components

94 Pipe connections

9General

10Docking alternatives

155 Electrical connections

15General

18Connections

21Optional connections

27Connecting accessories

286 Commissioning and adjusting

28Preparations

Commissioning with NIBE air/water heat

pump

Commissioning with additional heating

only

28Check the reversing valve

28Check AUX socket

28Cooling mode

29Start guide

30Setting the cooling/heating curve

32Setting hot water circulation

32Pool

33SG Ready

347 Control - Introduction

34Display unit

35Menu system

388 Control

38Menu 1 - INDOOR CLIMATE

39Menu 2 - HOT WATER

39Menu 3 - INFO

40Menu 4 - MY SYSTEM

41Menu 5 - SERVICE

509 Service

50Service actions

5310 Disturbances in comfort

53Manage alarm

53Troubleshooting

54Additional heating only

5511 Accessories

5712 Technical data

57Dimensions and setting-out coordinates

58Technical specifications

59Electrical circuit diagram

65Index

3Table of Contents |SMO 40

Safety information

This manual describes installation and service proced-

ures for implementation by specialists.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Chil-

dren shall not play with the appliance.

Cleaning and user maintenance shall

not be made by children without super-

vision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2015.

Symbols

NOTE

This symbol indicates danger to machine or

person.

Caution

This symbol indicates important information

about what you should observe when main-

taining your installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

SMO 40 is CE marked and fulfils IP21.

The CE marking means that NIBE ensures that the

product meets all regulations that are placed on it

based on relevant EU directives. The CE mark is obligat-

ory for most products sold in the EU, regardless where

they are made.

IP21 means that objects with a diameter larger than

or equivalent to 12.5 mm cannot penetrate and cause

damage and that the product is protected against

vertically falling drops of water.

Serial number

The serial number can be found on the upper side of

the cover on the control module.

LEK

Serial number

Caution

Always give the product's serial number when

reporting a fault.

Country specific information

Installer manual

This installer manual must be left with the customer.

SMO 40Chapter 1 | Important information4

1 Important information

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person. Fill in the page for information about installation data in the User

manual.

DateSignatureNotesDescription

✔

Electricity (page 15)

Communication, heat pump

Supply connected 230 V

Outside sensor

Room sensor

Temperature sensor, hot water charging

Temperature sensor, hot water top

Temperature sensor, external flow line

Temperature sensor, external return line

Charge pump

Shuttle valve

AUX 1

AUX 2

AUX 3

AUX 4

AUX 5

AUX 6

AA3-X7

Dipswitch

Miscellaneous

Checking additional heater

Checking the function of the reversing

valve

Checking charge pump function

Completed installation check of heat

pump and associated equipment

5Chapter 1 | Important informationSMO 40

......................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Contact information

KNV Energietechnik GmbH, Gahberggasse 11, 4861 SchörflingAT

Tel: +43 (0)7662 8963-0 Fax: +43 (0)7662 8963-44 E-mail: mail@knv.at www.knv.at

NIBE Wärmetechnik c/o ait Schweiz AG, Industriepark, CH-6246 AltishofenCH

Tel: (52) 647 00 30 Fax: (52) 647 00 31 E-mail: inf[email protected] www.nibe.ch

Druzstevni zavody Drazice s.r.o, Drazice 69, CZ - 294 71 Benatky nad JizerouCZ

Tel: +420 326 373 801 Fax: +420 326 373 803 E-mail: [email protected] www.nibe.cz

NIBE Systemtechnik GmbH, Am Reiherpfahl 3, 29223 CelleDE

Tel: 05141/7546-0 Fax: 05141/7546-99 E-mail: inf[email protected] www.nibe.de

Vølund Varmeteknik A/S, Member of the Nibe Group, Brogårdsvej 7, 6920 VidebækDK

Tel: 97 17 20 33 Fax: 97 17 29 33 E-mail: inf[email protected] www.volundvt.dk

NIBE Energy Systems OY, Juurakkotie 3, 01510 VantaaFI

Puh: 09-274 697 0 Fax: 09-274 697 40 E-mail: inf[email protected] www.nibe.fi

NIBE Energy Systems France Sarl, Zone industrielle RD 28, Rue du Pou du Ciel, 01600 ReyrieuxFR

Tel : 04 74 00 92 92 Fax : 04 74 00 42 00 E-mail: inf[email protected] www.nibe.fr

NIBE Energy Systems Ltd, 3C Broom Business Park, Bridge Way, Chesterfield S41 9QGGB

Tel: 0845 095 1200 Fax: 0845 095 1201 E-mail: inf[email protected] www.nibe.co.uk

NIBE Energietechniek B.V., Postbus 634, NL 4900 AP OosterhoutNL

Tel: 0168 477722 Fax: 0168 476998 E-mail: inf[email protected] www.nibenl.nl

ABK AS, Brobekkveien 80, 0582 Oslo, Postadresse: Postboks 64 Vollebekk, 0516 OsloNO

Tel. sentralbord: +47 23 17 05 20 E-mail: [email protected] www.nibeenergysystems.no

NIBE-BIAWAR Sp. z o. o. Aleja Jana Pawła II 57, 15-703 BIAŁYSTOKPL

Tel: 085 662 84 90 Fax: 085 662 84 14 E-mail: sekretariat@biawar.com.pl www.biawar.com.pl

Tel./fax +7 831 419 57 06 E-mail: [email protected] www.nibe-evan.ru

NIBE AB Sweden, Box 14, Hannabadsvägen 5, SE-285 21 MarkarydSE

Tel: +46-(0)433-73 000 Fax: +46-(0)433-73 190 E-mail: inf[email protected] www.nibe.se

For countries not mention in this list, please contact Nibe Sweden or check www.nibe.eu for more information.

SMO 40Chapter 1 | Important information6

Mounting

NOTE

For wall mounting, use the mounting adapted

for the base.

120

310 35

410

360

215

120

Use all mounting points and install SMO 40 upright flat

against the wall without any part of the control module

protruding out beyond the edge of the wall.

Leave at least 100 mm free space around the control

module to facilitate access and cable routing on install-

ation and service.

NOTE

Access the screws for installing the front cover

from underneath.

Supplied components

Room sensorOutside sensor

LEK

Temperature sensorInsulation tape

LEK

Cable tiesAluminium tape

LEK

Current sensorHeating pipe paste

Installatörshandbok

SMO 40

Tillbehörskort

Tillbehör

IHBSE 1345-1

331075

IHB SMO 40 Accessory

board

7Chapter 2 | Delivery and handlingSMO 40

2 Delivery and handling

L N 1 1 0 2 3 4PE

1 2 3 4

LEK

AA2

AA4-XJ3

SF1

AA5

PF3 AA4

AA3

AA7

AA4-XJ4

L N 1 1 0 2 3 4PE

1 2 3 4

LEK

AA2

FA1

AA7

UB2UB1

Electrical components

Base cardAA2

Input circuit boardAA3

Display unitAA4

AA4-XJ3 USB socket

AA4-XJ4 Service outlet (No function)

Accessory cardAA5

Extra relay circuit boardAA7

Miniature circuit-breakerFA1

Emergency mode relayK2

Terminal block, incoming electrical supplyX1

Terminal block, AUX4 - AUX6X2

SwitchSF1

Serial number platePF3

Cable grommet, incoming supply electricity,

power for accessories

UB1

Cable gland, signalUB2

Designations in component locations according to

standard IEC 81346-1 and 81346-2.

SMO 40Chapter 3 | The Control Module Design8

3 The Control Module Design

General

Pipe installation must be carried out in accordance with

current norms and directives. See manual for compat-

ible NIBE air/water heat pump for installation of the

heat pump.

Compatible NIBE air/water heat pumps

Compatible NIBE air/water heat pumps must be

equipped with a control card that has at least the

software version given in the following list. The control

card version is displayed in the heat pump's display (if

applicable) upon start-up.

Software versionProduct

55F2015

55F2016

118F2020

55F2025

55F2026

all versionsF2030

all versionsF2040

55F2300

Symbol key

MeaningSymbol

Shut-off valve

Trim valve

Shunt / shuttle valve

Safety valve

Temperature sensor

Pressure gauge

Circulation pump

Particle filter

Auxiliary relay

Temperature sensor installation on pipe

LEK

The temperature sensors are mounted with heat con-

ducting paste, cable ties (the first cable tie is secured

to the pipe in the middle of the sensor and the other

cable tie is mounted approx. 5 cm beyond the sensor)

and aluminium tape. Then insulate with supplied insu-

lation tape.

NOTE

Sensor and communication cables must not

be placed near power cables.

9Chapter 4 | Pipe connectionsSMO 40

4 Pipe connections

Docking alternatives

SMO 40 can be connected with other products from

NIBE in several different ways, some of which are shown

below (accessories may be required).

Further option information is available at www.nibe.eu

and in the respective assembly instructions for the ac-

cessories used. See page 55 for a list of the accessories

that can be used with SMO 40.

Installations with SMO 40 can produce heating and

hot water. Cooling can also be produced, but it de-

pends on the heat pump that is used.

On cold days of the year when the access to energy

from the air is reduced the additional heating can

compensate and help to produce heat. The additional

heating is also good to have as assistance if the heat

pump ends up outside its working range or if it has

been blocked for any reason.

NOTE

The heating medium side and the hot water

side must be fitted with the necessary safety

equipment in accordance with the applicable

regulations.

This is the outline diagram. Actual installations

must be planned according to applicable

standards.

Explanation

SMO 40AA25

Outdoor sensor1)

BT1

Temperature sensor, hot water charging1)

BT6

Temperature sensor, hot water top1)

BT7

Temperature sensor, external supply line1)

BT25

Room sensor1)

BT50

Temperature sensor, external supply line

after electric heater

BT63

Temperature sensor, external return line1)

BT71

Circulation pump, Heating mediumGP10

Reversing valve, Hot water/Heating medi-

um2)

QN10

Pool system 1 to 2CL11 to 12

Unit box with accessory card2)

AA25

Temperature sensor, pool2)

BT51

Exchanger, poolEP5

Circulation pump, poolGP9

Particle filter, poolHQ4

Three way valve, pool2)

QN10

Trim valveRN10

Additional heatEB1

Expansion vesselCM5

Immersion heaterEB1

Safety valveFL10

Auxiliary relay/Contactor2)

KA1

Trim valveRN11

Shut-off valveQM42 to 43

Heat pump systemEB101 to

104

Unit box with accessory card2)

AA25

Temperature sensor, return line3)

BT3

Temperature sensor, condenser supply

line3)

BT12

Heat pumpEB101 to

104

Safety valveFL10

External circulation pump, climate systemGP10

Charge pump2)

GP12

Particle filter3)

HQ1

Drain valve, Heating mediumQM1

Shut-off valve, Heating medium, FlowQM31

Shut off valve, Heating medium, ReturnQM32

Shut-off valveQM43

Non-return valveRM11

Climate system 2 to 3EP21 to 22

Unit box with accessory card2)

AA25

Temperature sensor, heating medium

supply2)

BT2

Temperature sensor, heating medium re-

turn2)

BT3

Circulation pump2)

GP20

SMO 40Chapter 4 | Pipe connections10

Autres manuels pour SMO 40

Table des matières

Autres manuels Nibe Unité de contrôle

Nibe

Nibe SMO 20 Manuel utilisateur

Nibe

Nibe RMU S40 Guide de l'utilisateur

Nibe

Nibe POOL 500 Guide de l'utilisateur

Nibe

Nibe SMO S40 Manuel utilisateur

Nibe

Nibe AXC 20 Guide de l'utilisateur

Nibe

Nibe SAM 41 Guide de l'utilisateur

Nibe

Nibe EME 20 Guide de l'utilisateur

Nibe

Nibe MODBUS 40 Guide de l'utilisateur

Nibe

Nibe VVM 325 Guide de l'utilisateur

Nibe

Nibe RMU S40 Guide de l'utilisateur

Nibe

Nibe VVM 225 UK 1x230V Manuel utilisateur

Nibe

Nibe VVM 310 EMK Guide de l'utilisateur

Nibe

Nibe HPAC 40 Guide de l'utilisateur

Nibe

Nibe EBV 200 Manuel utilisateur

Nibe

Nibe DEH 310 Guide de l'utilisateur

Nibe

Nibe MODBUS 40 Guide de l'utilisateur

Nibe

Nibe SMO 20 Guide de l'utilisateur

Nibe

Nibe VVM 320 Guide de l'utilisateur

Nibe

Nibe EME 20 Guide de l'utilisateur

Nibe

Nibe SMO 20 UK Guide de l'utilisateur

Nibe

Nibe MODBUS 40 Guide de l'utilisateur

Nibe

Nibe VCC11 Guide de l'utilisateur

Nibe

Nibe SMS 40 Guide de l'utilisateur

Nibe

Nibe SMO 20 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur