National Instruments FieldPoint FP-1601 Manuel utilisateur

FieldPoint

1FP-1601 Quick Start Guide

National Instruments Corporation

FP-1601 FieldPoint Quick Start Guide

What You Need

to Get Set Up

• FP-1601 network module

• 35 mm DIN rail

• Two DIN rail locks (included)

• Terminal base(s)

• I/O module(s)

• 11–30 VDC power supply

• Accessories: Ethernet cable,

flathead screwdriver

• PC running Windows

• National Instruments FieldPoint

Software CD

Install the Network Module

Mount the module on a DIN rail.

A. Unlock rail clip.

322978c.qxd 4/4/2003 4:08 PM Page 1

FP-1601 Quick Start Guide ni.com

NOTE Do not use spliced DIN rails. Use only a single DIN rail.

B. Hook lip on back of module

onto top of DIN rail, press

down, and snap into place.

C. Slide module into position

and lock rail clip.

322978c.qxd 4/4/2003 4:08 PM Page 2

3FP-1601 Quick Start Guide

National Instruments Corporation

Install the Terminal Base(s)

CAUTION Connect the terminal bases to the network module before applying

power to the module. Do

not

connect or disconnect terminal bases while

power is applied to the network module.

A. Unlock rail clip.

B. Press base onto rail.

322978c.qxd 4/4/2003 4:08 PM Page 3

D. Repeat for each terminal base, up to nine for each network module in most cases.

You can use one or two extender cables (which you can order separately) if the

FieldPoint bank is too long for the available space. Make sure there are no gaps

between terminal bases.

E. You

must

install DIN rail locks at each end of the bank to ensure reliable

connections between terminal bases and network module. Two rail locks are

included with each network module. Place protective cover on last base.

C. Slide base into position and

lock rail clip. Be careful not

to bend any pins.

FP-1601 Quick Start Guide ni.com

322978c.qxd 4/4/2003 4:08 PM Page 4

5FP-1601 Quick Start Guide

National Instruments Corporation

Install the I/O Module(s)

It does not matter where you install each I/O module, except in the following cases:

• If you plan to cascade power between any I/O modules using the V and C terminals,

those modules should be grouped together.

• For more accurate measurements, place thermocouple modules away from heat

sources, including network modules and relay modules.

A. Align slots on module with guide rails

on base, and press module onto base

until terminal base latch locks module

in place.

B. Repeat for each I/O module.

CAUTION Cascading power defeats isolation.

Connect the FP-1601 to the Network

Connect the FP-1601 to an

Ethernet network by

connecting the RJ-45

Ethernet port of the

FP-1601 to an Ethernet

hub using a standard

Category 5 Ethernet cable.

Straight-Through

UTP Cable

Straight-Through

UTP Cable

322978c.qxd 4/4/2003 4:08 PM Page 5

FP-1601 Quick Start Guide ni.com

Wire Power to the FieldPoint System

A. Connect power supply leads to the V and C terminals of the network module. Use an

11–30 VDC, 15 W minimum power supply such as the NI FP-PS-4. Refer to the I/O

module operating instructions for the power requirements of each module. Refer to

the

Specifications

section of this document for instructions on calculating the

power requirement of the FieldPoint bank.

B Connect power to the I/O modules that require external power for outputs (examples

include output, counter, relay, PWM, PG, and QUAD modules). It is generally best to

power each such module by connecting an external power supply to the VSUP and

COM terminals. Refer to the I/O module operating instructions for power

requirements, detailed wiring diagrams, and safe wiring practices.

Optionally, you can connect an

FP-1601 directly to a computer using

an Ethernet crossover cable.

Do not use a cable longer than 100 m.

If you are using a 100 Mbps Ethernet,

National Instruments recommends using a Category 5 shielded twisted-pair cable.

If you need to build your own cable, refer to the

FP-1601 User Manual

specifications

section for cabling details.

Crossover Cable

322978c.qxd 4/4/2003 4:08 PM Page 6

7FP-1601 Quick Start Guide

National Instruments Corporation

FP-AI-100 FP-AO-200 FP-RLY-420 FP-TC-120

15 16 V

31 32 C

V132

C17 18

Separate Power Supply

(Recommended)

Cascaded Power

(Reduces Isolation)

No External

Power Required

Power supply connected to

VSUP and COM terminals

FP-1601

CAUTION Cascading power from neighboring bases or network modules

defeats isolation between cascaded modules.

CAUTION Cascading

power defeats isolation.

Shades of gray indicate

different voltage potentials.

322978c.qxd 4/4/2003 4:08 PM Page 7

Power Up the FieldPoint System

FP-1601 Quick Start Guide

Connect to Field Devices

Use the operating instructions for each I/O module to help you connect field devices.

ni.com

CAUTION Connect terminal bases to the FP-1601 before applying power.

Make sure the RESET DIP switch is

not on. Plug in each power supply to

the FieldPoint bank. You should see

the POWER and STATUS LEDs come

on. After about 5 seconds, the

STATUS LED begins flashing, one

flash at a time. This indicates that the

FP-1601 is ready to be configured. If

the LEDs do not follow this sequence,

refer to the

FP-1601 User Manual

troubleshooting appendix.

RESET

322978c.qxd 4/4/2003 4:08 PM Page 8

9FP-1601 Quick Start Guide

National Instruments Corporation

Install Software on the Host PC

A. Install the software packages you plan to use, such as LabVIEW, LabVIEW RT,

Measurement Studio, VI Logger, or LabWindows™/CVI™, before you install the

FieldPoint software. The FieldPoint software installation installs the LabVIEW VIs

and examples and the LabWindows/CVI instrument driver only if it finds the

corresponding development software installed.

B. Close all other applications.

C. Insert the National Instruments FieldPoint

Software CD into the CD-ROM drive of

your computer.

D. Follow the onscreen instructions to

complete the installation.

NOTE If the setup does not launch automatically, select Start»Run from

Windows, enter d:\setup, where dis the letter of the CD-ROM drive, and

select OK.

322978c.qxd 4/4/2003 4:08 PM Page 9

Configure the FP-1601

Launch NI Measurement & Automation Explorer (MAX) to configure the FP-1601. For

information about configuring the FP-1601 in software, refer to the

Measurement &

Automation Explorer Help for FieldPoint

(Start»Programs»National Instruments»

FieldPoint»FieldPoint Help).

FP-1601 Quick Start Guide ni.com

322978c.qxd 4/4/2003 4:08 PM Page 10

Table des matières

Autres manuels National Instruments Unité de contrôle

National Instruments

National Instruments NI 9760 Manuel utilisateur

National Instruments

National Instruments FieldPoint cFP-DI-304 Manuel utilisateur

National Instruments

National Instruments SCXI SCXI-1102 Manuel utilisateur

National Instruments

National Instruments Network Adapter NI PXIe-6672 Manuel utilisateur

National Instruments

National Instruments SCXI-1520 Manuel

National Instruments

National Instruments 9501 C Series Manuel utilisateur

National Instruments

National Instruments ISM-7400 Manuel utilisateur

National Instruments

National Instruments NI 9476E Manuel utilisateur

National Instruments

National Instruments PXIe-4310 Manuel utilisateur

National Instruments

National Instruments Module SCXI-1503 Manuel

National Instruments

National Instruments SCC-DO01 Manuel utilisateur

National Instruments

National Instruments 7340 Manuel utilisateur

National Instruments

National Instruments FlexRIO PXI-79 R Series Manuel utilisateur

National Instruments

National Instruments FBUS-HSE/H1 LD Manuel utilisateur

National Instruments

National Instruments TB-4304 Manuel utilisateur

National Instruments

National Instruments FIELDPOINT FP-1600 Manuel utilisateur

National Instruments

National Instruments PXIe-6594 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments Relay Module SCC-RLY01 Manuel utilisateur

National Instruments

National Instruments PXIe-4302 Manuel

National Instruments

National Instruments REM-11102 Manuel utilisateur

National Instruments

National Instruments NI 9246 Manuel

National Instruments

National Instruments NI 9503 Manuel utilisateur

National Instruments

National Instruments NI 9775 Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur