Moxa Technologies EtherDevice EDS-510A-3GT Manuel

P/N: 1802005100015

EDS-510A

Hardware Installation Guide

Moxa EtherDevice™ Switch

Eighth Edition, April 2014

- 2 -

Package Checklist

The EDS-510A is shipped with the following items. If any of these items

are missing or damaged, please contact your customer service

representative for assistance.

•1 EDS-510A EtherDevice Switch

•Hardware Installation Guide (this guide)

•CD-ROM with user’s manual and Windows utility

•Moxa product warranty statement

•RJ45 to DB9 console port cable

•Protective caps for unused ports

•DIN-Rail mounting kit (attached to the EDS-510A’s rear panel by

default)

Optional Accessories

•SFP-1GSXLC: Small Form factor Pluggable transceiver with

1000BaseSX, LC, 0.5km, 0 to 60°C

•SFP-1GSXLC-T: Small Form factor Pluggable transceiver with

1000BaseSX, LC, 0.5km, 20 to 75°C

•SFP-1GLXLC: Small Form factor Pluggable transceiver with

1000BaseLX, LC, 10km, 0 to 60°C

•SFP-1GLXLC-T: Small Form factor Pluggable transceiver with

1000BaseLX, LC, 10km, -40 to 75°C

•SFP-1GLHXLC: Small Form factor Pluggable transceiver with

1000BaseLHX, LC, 40 km, 0 to 60°C

•SFP-1GLHXLC-T: Small Form factor Pluggable transceiver with

1000BaseLHX, LC, 40 km, -40 to 75°C

•SFP-1GZXLC: Small Form factor Pluggable transceiver with

1000BaseZX, 80 km, LC, 0 to 60°C

•ABC-01: Automatic Backup Configurator via RS-232 Console Port, 0

to 60°C

•DR-4524—DIN-Rail Power Supply (24 VDC, 45W/2A, with 85 to 264

VAC input)

•DR-75-24—DIN-Rail Power Supply (24 VDC, 75W/3.2A, with 85 to

264 VAC input)

•DR-120-24—DIN-Rail Power Supply (24 VDC, 120W/5A, with 88 to

132 VAC/176 to 264 VAC input by switch)

•EDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server

software and user’s manual

•WK-46—Wall Mounting Kit (will be shipped with the product)

•RK-4U—4U-high 19" rack mounting kit

- 3 -

Panel Views of EDS-510A

1. 1 to 7: 10/100BaseT(X) port

2. G1:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

10/100/1000BaseT(X) port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

3. G2:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

1000BaseSX/LX/LHX/ZX port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

4. G3:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

1000BaseSX/LX/LHX/ZX port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

5. G1, G2, G3: LED indicators for

1000 Mbps ports

6. PWR1: LED for power input 1

7. PWR2: LED for power input 2

8. FAULT: LED indicator

9. MSTR/HEAD: LED indicator

10.

CPLR/TAIL: LED indicator

11.

100M: LED indicator for TP port

12.

10M: LED indicator for TP port

13.

Model Name

- 4 -

Top Panel:

1. Ground screw

2. RS-232 console port

3. Heat dissipation orifices

4. DIP switches for Ring Master, Ring

Coupler, and Turbo Ring

5. 6-pin terminal block for

DI 1, DI 2,

and PWR 2

6. 6-pin terminal block for PWR1,

Relay 1, and Relay 2

Rear Panel:

1. Screw holes for Wall Mounting Kit

2. DIN-Rail Kit

Mounting Dimensions

Unit = mm (inch)

- 5 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS-510A when you take it out of the box. If you need

to reattach the DIN-Rail attachment plate to the EDS-510A, make sure

the stiff metal spring is situated towards the top, as shown by the

following figures.

STEP 1

—

Insert the top of the

DIN

-Rail into the slot just below the

stiff metal spring.

STEP 2

—

The DIN-Rail attachment

unit will snap into place as shown

the following illustration.

To remove the EDS-510A from the DIN-Rail, simply reverse Steps 1 and

2 above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa

EDS-510A on the wall, as shown in the following illustrations:

STEP 1—Remove the

aluminum DIN

-Rail

attachment plate from the

rear panel

of the EDS-510A

and then attach the wall

mount plates

with M3

screws

, as shown in the

figure

at the right.

STEP 2—Mounting the EDS-510A on the wall requires

4 screws. Use the

EDS-510A, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be less

than 3.5

mm in diameter, as shown in the figure on a

right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

- 6 -

STEP 3—Once the screws are fixed

the wall, insert the four screw

heads through the wide parts of the

keyhole

shaped apertures, and then

slide

the EDS-510A downwards, as

indicate

d in the figure at the right.

Tighten the four screws for

stability

ATEX Information

1. Certificate number DEMKO 08 ATEX 0810937x

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nA nC IIC T4 Gc)

4. Standards covered ( EN 60079-0:2012, EN60079-15:2010)

5. The conditions of safe usage:

•These products must be mounted in an IP54 enclosure.

•Install in an area of pollution degree 2 or less.

•Use a conductor wire of size 0.2 mm² or greater.

•PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE

APPARATUS, TO PREVENT THE RATED VOLTAGE BEING

EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE

THAN 40 %

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to

be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

afety Extra-Low V

oltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

afety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the

unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

- 7 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together

•You should separate input wiring from output wiring

•We advise that you label the wiring to all devices in the system.

Grounding the Moxa EDS-510A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

- 8 -

Wiring the Relay Contact

The EDS-510A has two sets of relay outputs—relay 1 and relay 2. Each

relay contact uses two contacts of the terminal block on the EDS-510A’s

top panel. Refer to the next section for detailed instructions on how to

connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor. In this section,

we illustrate the meaning of the two contacts used to connect the relay

contact.

FAULT:

The two sets of relay contacts of the

-pin terminal block connector are

used to detect user

-configured

events. The two wires attached to

the

fault contacts form an open

circuit when a user

configured event

is triggered. If a user

-configured

event does not occur, the

fault

circuit remains closed.

Wiring the Redundant Power Inputs

The EDS-510A has two sets of power inputs—power input 1 and power

input 2. The top two contacts and the bottom two contacts of the 6-pin

terminal block connector on the EDS-510A’s top panel are used for the

two digital inputs. The top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the negative/positive

DC wires into the V

-/V+ terminals,

respectively.

STEP 2:

To keep the DC wires from

pulling loose, use a small flat

blade

screwdriver to tighten the

wire

-clamp screws on the front of

the terminal block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on

the EDS-510A’s top

panel.

- 9 -

Wiring the Digital Inputs

The EDS-510A has two sets of digital inputs, DI 1 and DI 2. Each DI

consists of two contacts of the 6-pin terminal block connector on the

EDS-510A’s top panel, which are used for the two DC inputs. The top and

front views of one of the terminal block connectors are shown here.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴

/I1 terminals, respectively.

STEP 2:

To keep the DI wires from

pulling loose, use a small flat

blade

screwdriver to tighten the

wire

-clamp screws on the front of

the terminal block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on

the EDS-510A’s top

panel.

Communication Connections

Each EDS-510A switch has 3 types of communication port:

•1 RJ45 console port (RS-232 interface)

•7 10/100BaseTX Ethernet ports

•3 gigabit Ethernet ports:

3 10/100/1000BaseTX ports, or 1 10/100/1000BaseTX and 2

1000BaseSFP (mini-GBIC) ports, or 3 1000BaseSFP (mini-GBIC)

ports

In this section, we present two types of diagrams—Pinout Diagrams and

Cable Wiring Diagrams—that convey information about the ports and the

cables used to connect the EDS-510A to other devices:

Pinouts—The “Pinouts” diagrams display the type of signal passing

through each of the port’s pins.

Cable Wiring—The “Cable Wiring” diagrams present standard cable

wiring schemes for cables used to connect the EDS-510A’s ports to other

devices. These diagrams display three pieces of information:

1. When building your own cable, refer to the “pin-to-pin” cable

wiring information displayed between the two vertical dashed lines

to see which pin of the connector on the left should be connected to

which pin of the connector on the right.

2. The information to the left of the left vertical dashed lines gives the

pinouts of the relevant EDS-510A port.

3. The information to the right of the right vertical dashed line gives the

pinouts of the opposing device’s port.

NOTE

1. The pin numbers for male DB9 connectors and hole

numbers for female DB9 connectors are labeled on the

connector.

2. The pin numbers for 10-

pin RJ45 connectors (and ports) are

typically not labeled on the connector (or port). Refer to the

following Pinout and Cable Wiring diagrams to see how

10-pin RJ45 pins are numbered.

- 10 -

RS-232 Connection

The EDS-510A has one RS-232 (10-pin RJ45) console port, located on the

top panel. Use either an RJ45-to-DB9 (see the cable following wiring

diagrams) to connect the EDS-510A’s console port to your PC’s COM port.

You may then use a console terminal program, such as Moxa PComm

Terminal Emulator, to access the EDS-510A’s console configuration

utility.

RJ45 (10-pin) Console Port Pinouts

Description

---

DSR

RTS

---

TxD

RxD

GND

CTS

DTR

---

RJ45 (10-pin) to DB9 (F) Cable Wiring

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS-510A’s front panel are

used to connect to Ethernet-enabled devices. Most users configure these

ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are

adjusted automatically depending on the type of Ethernet cable used

(straight-through or cross-over), and the type of device (NIC-type or

HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7728 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manuel

Moxa Technologies

Moxa Technologies TN-5308 Manuel utilisateur

Moxa Technologies

Moxa Technologies ICS-G7 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-G7509 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-516A Series Manuel

Moxa Technologies

Moxa Technologies PT-510 Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel

Moxa Technologies

Moxa Technologies MDS-G4000-L3-4XGS Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7528 Manuel

Moxa Technologies

Moxa Technologies EDS-510E Series Manuel

Moxa Technologies

Moxa Technologies NPort 1220 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manuel

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manuel utilisateur

Moxa Technologies

Moxa Technologies S9450I Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE-P24-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-600 Series Manuel

Moxa Technologies

Moxa Technologies EDS-P308 Series Manuel

Moxa Technologies

Moxa Technologies IKS-G6524A Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-828 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PN Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur