Moxa Technologies PowerTrans PT-7728-PTP Manuel utilisateur

P/N: 1802072000011

*1802072000011*

PT-7728-PTP

Quick Installation Guide

Moxa PowerTrans Switch

Edition 5.0, February 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Package Checklist

The Moxa PowerTrans switch is shipped with the following items. If any of

these items are missing or damaged, please contact your customer

service representative for assistance.

•1 Moxa PowerTrans Switch

•RJ45 to DB9 console port cable

•Protective caps for unused ports

•2 rackmount ears

•CD-ROM with User’s Manual and SNMP MIB file

•Quick installation guide (printed)

•Warranty card

Panel Layout

1. System status LEDs

2. Interface Module mode LEDs

3. Interface Module port LEDs

4. Push-button switch to select mode for Interface Module

5. Model Name

6. Fast Ethernet Interface Modules with PPS (pulse per second) output

signal

7. Serial Console port

8. 10-pin terminal block for power inputs and relay output

9. Rackmounting kit

- 3 -

Dimensions (unit = mm)

Fast Ethernet Interface Modules (slots 1, 2, and 3)

- 4 -

Fast Ethernet Interface Modules (slot 4)

Gigabit Ethernet Interface Modules (slot 4)

Gigabit PRP/HSR Interface Modules (slot 4)

Rack Mounting

Use four screws to attach the PT switch to a standard rack.

NOTE

Two additional rackmount

ears can be ordered as an option. Use

them to secure the rear of the chassis in high

-vibration

environments.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa PowerTrans Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allow

ed for each wire size.

If the current goes above the

allowed

maximum, the wiring could

overheat, causing serious damage to your equipment.

- 5 -

Grounding Moxa PowerTrans Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface before connecting devices.

Wiring the Power Inputs

The PT series of switches supports dual redundant power supplies:

“Power Supply 1 (PWR1)” and “Power Supply 2 (PWR2).” The connections

for PWR1, PWR2 and the RELAY are located on the terminal block. The

front view of the terminal block connectors are shown below.

Wiring the Relay Contact

Each PT switch has one relay output. Refer to the next section for detailed

instructions on how to connect the wires to the terminal block connector

and how to attach the terminal block connector to the terminal block

receptor.

FAULT: The relay contact of the 10-pin terminal block connector is used

to detect user-configured events. The two wires attached to the RELAY

contacts form an open circuit when a user-configured event is triggered.

If a user-configured event does not occur, the RELAY circuit will be closed.

Wiring the Redundant Power Inputs

Each PT switch has two sets of power inputs: power input 1 and power

input 2.

STEP 1: Insert the dual set positive/negative DC wires into PWR1 and

PWR2 terminals (+ pins 1, 9; – pins 2, 10). Or, insert the L/N AC

wires into PWR1 and PWR2 terminals (L pins 1, 9; N pins 2, 10)

- 6 -

STEP 2: To keep the DC or AC wires from pulling loose, use a screwdriver

to tighten the wire-clamp screws on the front of the terminal block

connector.

NOTE

For dielectric strength (HIPOT) test, users must remove the

metal jumper located on terminals 3, 4, and 7, 8 of the terminal

block to avoid damage.

LED Indicators

LED

Color

State

Description

System LEDs

STAT GREEN On

System has passed self-diagnosis test

on boot-up and is ready to run.

Blinking

System is undergoing the self-diagnosis

test.

RED

System failed self-diagnosis on boot-up.

PWR1 AMBER On

Power is being supplied to the main

module’s power input PWR1.

Off

Power is not being supplied to the main

module’s power input PWR1.

PWR2 AMBER On

Power is being supplied to the main

module’s power input PWR2.

Off

Power is not being supplied to the main

module’s power input PWR2.

FAULT RED

On The corresponding PORT alarm is

enabled and a user-configured event

has been triggered.

Off

The corresponding PORT alarm is

enabled and a user-configured event

has not been triggered, or the

corresponding PORT alarm is disabled.

MSTR/

HEAD GREEN

This PT switch is set as the Master of the

Turbo Ring, or as the Head of the Turbo

Chain.

Blinking

The PT switch has become the Ring

Master of the Turbo Ring, or the

Head of

the Turbo Chain, after the Turbo Ring or

the Turbo Chain went down.

Off

The PT switch is not the Master of this

Turbo Ring,

or is set as a Member of the

Turbo Chain.

CPLR/

TAIL GREEN

The PT switch coupling function is

enabled to form a backup path, or it is

set as the Tail of the Turbo Chain.

Blinking

Turbo Chain is down.

Off

This PT switch disabled the coupling

function, or is set as a Member of the

Turbo Chain.

- 7 -

LED

Color

State

Description

Mode LEDs

LNK/ACT GREEN

The corresponding module port’s link is

active.

Blinking

The corresponding module port’s data is

being transmitted.

Off

The corresponding module port’s link is

inactive.

SPEED GREEN

Off

The corresponding module port’s data is

being transmitted at 10 Mbps.

The corresponding module port’s data is

being transmitted at 100 Mbps.

Blinking

The corresponding module port’s data is

being transmitted at 1000 Mbps.

FDX/HDX GREEN On

The corresponding module port’s data is

being transmitted in full-duplex mode.

Off

The corresponding module port’s data is

being transmitted in half-duplex mode.

RING/

CHAIN

PORT GREEN On

The corresponding module’s port is the

ring or chain port of this PT switch.

Off The corresponding module’s port is not

the ring or chain port of this PT switch.

COUPLER

PORT GREEN On

The corresponding module’s port is the

coupler port of this PT switch.

Off

The corresponding module’s port is not

the coupler port of this PT switch.

Specifications

Technology

Standards IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x,

802.1D, 802.1w, 802.1Q, 802.1p, 802.1X, 802.3ad

Flow control

IEEE 802.3x flow control, backpressure flow control

Interface

Fast Ethernet

10/100BaseT(X) or 100BaseFX (SC/ST connector or

SFP slot)

Gigabit Ethernet

10/100/1000BaseT(X), 1000BaseSX/LX/LHX/ZX

(SFP slot, LC connector)

System LED

Indicators

STAT, PWR1, PWR2, FAULT, MSTR/HEAD, CPLR/TAIL

Module LED

Indicators

LNK/ACT, FDX/HDX, SPEED, RING /CHAIN PORT,

COUPLER PORT

Alarm Contact

One relay output with current-carrying capacity of

3 A @ 30 VDC or 3 A @ 240 VAC

- 8 -

Optical Fiber (100BaseFX)

Distance

Multimode:

0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km)

0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km)

Single-mode:

0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km))

0 to 80 km, 1550 nm (9/125 um, 19 PS/(nm*km))

Min. TX Output

Multimode: -20 dBm; Single-mode: -5 dbm

Single-mode 80 km: -5 dBm

Max. TX Output Multimode: -10 dBm; Single-mode: 0 dbm

Single-mode 80 km: 0 dBm

RX Sensitivity

Multimode: -32 dBm; Single-mode: -34 dbm

Single-mode 80 km: -34 dBm

Power

Input Voltage

24 VDC (18 to 36V) or 48 VDC (36 to 72V) or

110/220 VDC/VAC (88 to 300 VDC and 85 to 264

VAC)

Input Current

Max. 2.38 A @ 24 VDC

Max. 1.12 A @ 48 VDC

Max. 0.59/0.30 A @ 110/220 VDC

Max. 0.49/0.26 A @ 110/220 VAC

Physical Characteristics

Housing

IP 30 protection, metal case

Dimensions

(W x H x D)

440 x 44 x 325 mm (17.32 x 1.73 x 12.76 in.)

Weight

5900 g

Installation

19” rack mounting

Regulatory Approvals

Safety

UL60950-1, CSA C22.2 No. 60950-1, EN60950-1

Power Automaton

IEC 61850-3, IEEE 1613

EMI

FCC Part 15, CISPR 32 class A

Environmental Limits

Operating Temp.

-40 to 85°C (-40 to 185°F)

Cold start of min. 100 VAC at -40°C

Storage Temp.

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity.

5 to 95% (non-condensing)

WARRANTY

5 years

Autres manuels pour PowerTrans PT-7728-PTP

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies TN-5308 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-600 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort S8458 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies IKS-6728 Series Manuel

Moxa Technologies

Moxa Technologies EDS-G4008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-2005-EL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE-P24-T Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel

Moxa Technologies

Moxa Technologies EOM-104 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-205A series Manuel

Moxa Technologies

Moxa Technologies PT-7528-24TX-HV Manuel utilisateur

Moxa Technologies

Moxa Technologies ICS-G7748A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G308-T Manuel

Moxa Technologies

Moxa Technologies EDS-408A Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G512E-8PoE Manuel

Moxa Technologies

Moxa Technologies ToughNet TN-5508 Series Manuel

Moxa Technologies

Moxa Technologies IKS-6700A series Manuel

Moxa Technologies

Moxa Technologies S9450I Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7728 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies UPORT 1200 series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7728 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-G7509 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur